The Firing Line Forums

Go Back   The Firing Line Forums > The Conference Center > General Discussion Forum

Reply
 
Thread Tools Search this Thread
Old March 11, 2013, 11:30 AM   #1
Erich
Senior Member
 
Join Date: January 8, 1999
Location: Albuquerque, NM, USA
Posts: 2,542
Displeased with Federal's response after ammo problems

I don’t usually gripe about customer service -in fact, my experience with firearms-related customer service - and reloading related customer service in particular - have been very good. But I had a bad experience with Federal just now, and thought I’d share it, because it was so unusual in relation to the service I’ve gotten on other ammunition issues.

So, yesterday I had brought a brand-new silver box of Federal Classic ammo to the range to try in my new-to-me pre-Model 30 Improved I-frame. The Federal Classic ammo was 98-gr RNL .32 S&W Long, part no. C32LB, lot number 3 19J155. Federal ammo is more expensive in this caliber than Eastern European stuff, but I figured the good thing about using big maker ammo from Federal would be that I’d be able to reload the empties. Based on decades of past experience, I figured I’d get quality brass after firing the low-pressure .32 S&W Long factory loads.

The ammo shot well enough (group at 10 yards), though was pretty tame (M 667.8/ES 78.95/SD 32.31).



But wait! Upon firing, I noticed that one round did a very odd spurt of stuff out of the bbl/cyl gap, and was surprised to find that I had to hammer on the ejector rod to get the rounds out of the cylinder. Out of five rounds, four split - and one had its primer pop out the back.





This was NOT the fault of the gun - I fired four other loadings on the same outing (two handloads - ironically in Federal cases, and two factory loadings by S&B and Aguila) with no problems whatsoever.

So, since this ammo wasn’t going to give me the reloadable cases that I’d been after, I figured I’d contact ATK; on advice of friend, I went to their site and filled out a contact form:

Quote:
Four out of five cases split on a new silver box of Federal Classic .32 S&W Long ammo, part no. C32LB, lot number 3 19J155. One primer protruded. The cases had to be forcibly extracted by hammering the ejector rod. This was not a problem with the gun, as several other loadings performed flawlessly.

Here are some photographs:

i225.photobucket.com/albums/dd222/505Erich/Handguns/2013-03-10_11-34-34_709.jpg

i225.photobucket.com/albums/dd222/505Erich/Handguns/2013-03-10_11-34-51_820.jpg

I deliberately purchased what I thought to be quality Federal ammo because I wanted the spent cases for reloading. Please contact me about this.
I was really surprised when Federal wrote back a terse, “Go Away” email:

Quote:
You bought old ammo, it has been sitting on the shelf. The brass split due to stress corrosion cracking. It was manufactured in 2003.

Thanks
Federal Ammunition
I was pretty amazed by this, and responded:

Quote:
Are you kidding me, or are you just insulting me? I've been happily reloading much of the same brass since the '80s, and you're going to tell me that your new, never-fired brass from only ten years ago will split when fired in a low-pressure factory loading in the .32 S&W Long cartridge.
I’ve not heard back. I’m not pleased with Federal/ATK’s handling of the situation; I would have expected that Federal/ATK would stand behind its products or care more about its customers.
Erich is offline  
Old March 11, 2013, 11:57 AM   #2
Cheap 870
Junior member
 
Join Date: November 12, 2011
Location: Ohio
Posts: 159
I posted this in another forum & now I'm posting it in this one.
That's how aggravated this makes me.


That response would've made me mad all so.
In my eyes it doesn't matter if factory ammo is 10yrs. old or 20yrs. old it sure shouldn't have done that. So what they are saying is that Federal Ammo has a shelf life??? If that's the case they should put an experation date on all their ammo boxes & when it expires you should be able to send it back for a refund.
This is redictulous & the response you recieved back is a joke.
And if you want to copy & post my response in your next email you have my permission.
Cheap 870 is offline  
Old March 11, 2013, 12:23 PM   #3
F. Guffey
Senior Member
 
Join Date: July 18, 2008
Posts: 7,249
http://www.turkmauser.com/ammo.aspx

http://www.turkmauser.com/ammo/mhbTurk.aspx

I no longer shoot this ammo, I know it is old, I have pulled the bullets, saved the powder and bullets then formed 30/06 cases to 8mm57 cases, all the problems went away. Number one, I shake the case to detect loose powder, if the powder is loose it only means the powder is loose on the bullet end, it does not guarantee the powder is not caked on the primer end, with that old ammo I would not pull the trigger then immediately open the bolt if there was a failure to fire.

No one can imagine the effect of pulling the trigger on a case with caked powder next to the bullet, I was given one of those ,you bet, no problem, and he is one of the best reloaders in South Texas, three boxes of the ugliest reloads I have ever seen. Not much room for forgiveness when the rifle was a 30/40 Crag with one locking lug.

I epoxied the cases into case trays, at the time I had little concern for those that were desperate for cases.

F. Guffey

Last edited by F. Guffey; March 11, 2013 at 12:25 PM. Reason: add a t to be
F. Guffey is offline  
Old March 11, 2013, 12:40 PM   #4
sunaj
Junior member
 
Join Date: February 27, 2013
Location: California
Posts: 84
If the brass has been stored properly, and they are saying 2002 mfc is so old that explains the brass splits I think I would avoid Federal brass from here on out
sunaj is offline  
Old March 11, 2013, 01:04 PM   #5
NWPilgrim
Senior Member
 
Join Date: September 29, 2008
Location: Oregon
Posts: 2,340
Wow, that is one of the worse CS responses I've seen from an ammo manufacturer. They are basically stating their ammo is no good after 10 years? Designed obsolescence?

Sounds more like the ATK webmaster responding then an actual ammunition engineer. I would ask to be forwarded to a supervisor who is a grown-up.
__________________
"The ultimate authority ... resides in the people alone. ... The advantage of being armed, which the Americans possess over the people of almost every other nation ... forms a barrier against the enterprises of ambition."
- James Madison
NWPilgrim is offline  
Old March 11, 2013, 01:24 PM   #6
Sevens
Senior Member
 
Join Date: July 28, 2007
Location: Ohio
Posts: 11,755
I'm with NWPilgrim. That's an idiotic response. I'm still loading component brass that I picked up off the range of the shooting club I began my shooting at, in 1988.

There's no way that ammo is too old. I really have no idea what the problem is, almost looks like Federal had a bad run of brass. While I can see a company referring to it's age as some manner of an "answer", the response they sent stinks quite a bit.

I don't know if this will help much, but when you've got handloading questions, they get funneled to Ben Amonette at ATK and although he's not always come through with helpful answers, he does tend to get back in a timely fashion. I'm not sure if he'll help with factory ammo problems, but I don't think it can hurt to go from two or more angles.

Ben.Amonette <at> ATK.com will send a note directly to him.
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss.
Sevens is offline  
Old March 11, 2013, 02:19 PM   #7
hardworker
Senior Member
 
Join Date: August 4, 2010
Posts: 820
Or it could have been a bad batch of ammo. Sounds like they were aware of the problem and told you why it happened.
hardworker is offline  
Old March 11, 2013, 02:47 PM   #8
zincwarrior
Senior Member
 
Join Date: July 1, 2011
Location: Texas, land of Tex-Mex
Posts: 2,259
I'm not surprised about Federal's lack of concern about their efficacy for reloading, however, split shells that can't be ejected, etc. pose a real risk, depending on what you are using them for. What type of satisfaction were you looking for-replacement, some sort of credit, or other recourse?
zincwarrior is offline  
Old March 11, 2013, 03:06 PM   #9
LE-28
Senior Member
 
Join Date: September 24, 2012
Location: North Carolina
Posts: 759
Quote:
they get funneled to Ben Amonette at ATK and although he's not always come through with helpful answers, he does tend to get back in a timely fashion.
I've had one dealing with Ben Amonette at ATK and he came through for me in a heartbeat, It was my mistake but he made it right with me in a New York second. I thought he was the gun powder guy but maybe he does more than that. I can't imagine he was the one that told you to go away. He sounded like a straight shooter to me and I was impressed by his willingness to make me happy with my problem. (Again, My Fault Entirely).

If you are 100% accurate with what all took place with your corrospondance, I doubt Ben was involved.

Last edited by LE-28; March 11, 2013 at 03:13 PM.
LE-28 is offline  
Old March 11, 2013, 03:09 PM   #10
reynolds357
Senior Member
 
Join Date: December 10, 2012
Posts: 6,161
I wish you could get in a time warp and go deal with Ruger in the early 80's. You would appreciate Federal's helpfulness if you had ever had the pleasure of dealing with Ruger in that era. Federal is basically saying, its their low end ammo and they dont really care. Would tick me off as well if they told me what they told you.
reynolds357 is offline  
Old March 11, 2013, 03:11 PM   #11
reynolds357
Senior Member
 
Join Date: December 10, 2012
Posts: 6,161
Suna J, Federal brass has been on my avoid list for a very long time if it bears their and not Lake City markings.
reynolds357 is offline  
Old March 11, 2013, 03:24 PM   #12
LE-28
Senior Member
 
Join Date: September 24, 2012
Location: North Carolina
Posts: 759
I'd like to know who sent you that reply. Can you post the corrospondance so we can see it?
LE-28 is offline  
Old March 11, 2013, 04:21 PM   #13
maillemaker
Senior Member
 
Join Date: August 30, 2010
Posts: 1,635
I find this post disturbing. Ammunition that has been sitting on a shelf for 10 years should work just fine.

Steve
maillemaker is offline  
Old March 11, 2013, 04:24 PM   #14
Erich
Senior Member
 
Join Date: January 8, 1999
Location: Albuquerque, NM, USA
Posts: 2,542
No kidding.

You've seen all the correspondence, LE-28. The Federal email came from an anonymous address: Anoka Prodserv <[email protected]>

Thank you all for your kind replies. (reynolds357, you cracked me up.) Before I went to law school, I did my time behind the counter of a gun store and in customer service - I remember well the magic words, "I'm so sorry that happened to you. That is not at all the experience that we want for our customers. How can I make it right for you?" You know, the kind of response you get from pretty much any CS person involved in any way with the reloading hobby.

A friend on another forum knows people and offered to put me in touch with the bigwigs at ATK. That's not really the point, though: I'm not really looking to be made whole or to help Federal rehabilitate their image at this point, just wanting to let fellow 'loaders know what sort of response they can expect if they encounter such issues.
Erich is offline  
Old March 11, 2013, 09:08 PM   #15
SL1
Senior Member
 
Join Date: November 8, 2007
Posts: 2,001
Another place where ATK seems to be having case issues is with their SPEER nickeled 357 Sig brass. It often showes a web of cracks in the shoulder area when factory ammo is fired.

I also bought some Federal "Champion" .45 ACP ammo at Walmart (because it was cheap) and found that its "FMJ" bullets were actually thick-plated, with a LOT of small dents on their noses. And they turned-out to be several mils out-of-round when I pulled a few. But, those cases did not split.

Seems like maybe there are some general QC problems at ATK these days.

On the other hand, I bought a lot of Federal factory ammo in the 1970s and am still shooting a lot of those cases these days. So, I guess things have changed.

SL1
SL1 is offline  
Old March 11, 2013, 10:28 PM   #16
F. Guffey
Senior Member
 
Join Date: July 18, 2008
Posts: 7,249
You bought old ammo, it has been sitting on the shelf. The brass split due to stress corrosion cracking. It was manufactured in 2003.

----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Chain of possession, I have no clue how the box of ammo was stored, as to ‘it does not take me long to look at it’, after I experience a problem with a box of ammo, I stop, who knows what the story would have been had a few of the cases been saved.

A friend called and was asking about Remington ammo, seems a pound owner of a new Ruger rifle and two boxes of Remington 30/06 ammo that had 5 cases to fail to fire fire out of 20, long story, he brought the 15 fired and 5 failed to fire cases over, no new box and no way of contacting the proud owner. We tore the ammo down and measure everything to the grain and thousandths, I was impressed. The fired cases would chamber in my chamber gage, I removed the primers then installed them back in the same case they were installed in, I chambered all 5 cases in one of my M1917s and fired them one at a time. I believe the cases would have fired in any of of sever M1917s, there were 5 attempts to fire the failed to fire cases in 3 different 30/06 rifles at the range. At the range that day it was ‘bad old Remington ammo’. I was impressed with their primers, hammered 5 times then bang when fired in a rifle that does not have a bashful firing pin.

F. Guffey
F. Guffey is offline  
Old March 12, 2013, 03:34 AM   #17
Sevens
Senior Member
 
Join Date: July 28, 2007
Location: Ohio
Posts: 11,755
Quote:
I can't imagine he was the one that told you to go away. He sounded like a straight shooter to me and I was impressed by his willingness to make me happy with my problem.
I hope you didn't get from my post any suggestion that Ben Amonette might have been involved in the lousy response he got. My bringing in his name was a suggestion of who I would send an e-mail to, to get to the bottom of this.
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss.
Sevens is offline  
Old March 12, 2013, 06:30 AM   #18
10 Spot Terminator
Senior Member
 
Join Date: January 3, 2008
Location: Central Oregon
Posts: 348
In a situation like that when you spoke to them the first time and knew in your heart yor were being handed a line of bull you should have told them of your affiliation with this and other widely used shooting forums. You then could have explained to them you would be all too happy to post their position along with graphic pictures of the failed brass for all to see and form their own opinion as to weather their ammo was safe ( they love that word ) to fire . You realize of course what you have is the very thing recalls are made of right ? Their position was WAY off the grid of acceptability.

10 Spot
10 Spot Terminator is offline  
Old March 12, 2013, 06:49 AM   #19
TimSr
Senior Member
 
Join Date: March 8, 2013
Location: Rittman, Ohio
Posts: 2,074
Sounds to me like an entire corporation will be taking the rap for the idiotic email from one person. I would escalate this to several others until you get a satisfactory response, or enough support for his stupidity to determine its a companywide policy issue, and not just one underling who answers email in a way that his superiors are unaware of. If you were a Federal exec, you would want to know. I would foreward your email and his repsonse to a dozen or so corporate Federal email addresses.

That you wanted the cases for reloading is irrelevant. Something was obviously wrong for this ammo to to generate excessive pressure that is both dangerous to the shooter and his equipment.
TimSr is offline  
Old March 12, 2013, 09:10 AM   #20
Erich
Senior Member
 
Join Date: January 8, 1999
Location: Albuquerque, NM, USA
Posts: 2,542
Actually, I'm pretty sure there was no excessive pressure - look at the chrono numbers. Thanks for all the replies - I'm not really concerned at this point about getting myself made whole so much as letting the shooting fraternity know 1) that I had a brass issue and you might, too, and 2) the pretty astonishingly uncaring response about a product that is unfit for its intended purpose.
Erich is offline  
Old March 12, 2013, 09:49 AM   #21
Palmetto-Pride
Senior Member
 
Join Date: May 31, 2009
Location: Charleston, SC
Posts: 2,071
I would try to at least call them and see if you could talk to someone, it would be ashamed to chalk up a company due to one person that may have received the emails, but who may not care or is just incompetent.
__________________
“The problem with socialism is that you eventually run out of other people's money.”

-Margaret Thatcher-
Palmetto-Pride is offline  
Old March 12, 2013, 10:08 AM   #22
jcwit
Senior Member
 
Join Date: October 28, 2007
Location: Upper Indiana
Posts: 609
I believe Federal will survive your attempt to discredit them.
__________________
U.S. Army Veteran
NRA Certified Range Officer
jcwit is offline  
Old March 12, 2013, 10:19 AM   #23
Brian Pfleuger
Moderator Emeritus
 
Join Date: June 25, 2008
Location: Austin, CO
Posts: 19,578
Moved to General Discussion...
__________________
Nobody plans to screw up their lives...
...they just don't plan not to.
-Andy Stanley
Brian Pfleuger is offline  
Old March 12, 2013, 04:54 PM   #24
leprechaun50
Member
 
Join Date: December 11, 2011
Location: SW Minnesota
Posts: 32
The company can't fix it if they don't know its broken. Take it up the ladder. That will serve two purposes. Lets them know they have a bad batch of ammo out there, and they have a customer service rep that needs to be fired.
leprechaun50 is offline  
Old March 12, 2013, 08:06 PM   #25
Aguila Blanca
Staff
 
Join Date: September 25, 2008
Location: CONUS
Posts: 18,433
Quote:
The company can't fix it if they don't know its broken. Take it up the ladder. That will serve two purposes. Lets them know they have a bad batch of ammo out there, and they have a customer service rep that needs to be fired.
^^^ This.

2003 is only ten years old. People have dug M1911s out of attics and barn lofts that have been left loaded since Grandpa came back from WW2 and the ammo doesn't split when fired.
Aguila Blanca is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:03 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.10087 seconds with 8 queries