December 25, 2008, 03:13 PM | #1 |
Senior Member
Join Date: October 11, 2008
Location: Dublin VA
Posts: 105
|
Brass Conversions
I have seen on the web where someone had asked a rabbi about taking a 30-06 brass and cutting it then trimming to size of a .45 acp. Has anyone here heard of this or even went further and have done this? From my understanding, after using hacksaw and cutting the brass then trimming it to size, nothing else except chamfer and deburring is needed. They also say you still have to use the large pistol primer. Would be intresting to find out if this practice is used.
Thanks |
December 25, 2008, 03:15 PM | #2 |
Junior member
Join Date: December 10, 2001
Location: Burbs of Minneapolis
Posts: 676
|
Not quite that simple, you would have to ream the case to accept the bullet.
There are much better uses of my time then to cut down 06 brass to make 45ACP brass. The 44 Auto Mag was made in such a way till brass was made in that cartridge. |
December 25, 2008, 03:28 PM | #3 |
Senior Member
Join Date: January 29, 2005
Location: Up Nort
Posts: 419
|
So what is the benefit of making 45 acp from 3006?
__________________
JSF "Is your rifle interesting? -Larry Potterfield |
December 25, 2008, 03:48 PM | #4 |
Senior Member
Join Date: January 18, 2006
Posts: 124
|
Nothing! I believe it's called "much ado about nothing!"
|
December 25, 2008, 05:42 PM | #5 |
Senior Member
Join Date: June 16, 2008
Location: Wyoming
Posts: 11,061
|
Anything is possible if not practical. You can do it, get a trim die, cut it off, put it in a case trimmer for the finish cut. Then you need a reamer for the inside of the case, the web is too thick on ''06 cases. Its time consuming, and a pain in the butt.. I did it making .41 Datonics cases. I have a reamer for the Datonics but its a bit too big for the ACP.
The question is, since 45 brass is so much cheaper the '06 brass is WHY. If the answer to save money, YOU WONT. If the answer is just to see if you can do it I'd say GO FOR IT. I could write a book on the crap I've done or tried to do, things that made no sinse what so ever, I mean some really dumb ideals, but I've enjoyed every minute of it. PS: When you're through with that project try making your own reloading dies, or whats more fun, cast bullet molds. Don't ever stop experimenting, but do be careful, Nothing says safty like a Lead Sled and a long string. If people were a afraid to try stuff, we'd still be throwing rocks.
__________________
Kraig Stuart CPT USAR Ret USAMU Sniper School Distinguished Rifle Badge 1071 |
December 26, 2008, 11:28 AM | #6 |
Senior Member
Join Date: October 11, 2008
Location: Dublin VA
Posts: 105
|
The reason for my asking is information and education. I am all new to reloading so when I find the chance to learn something new, I will ask questions on it. As far as why would I want to convert 06 to 45 acp, well, I can find tons of 06 cases at ranges and in the national forest when hunting. I do not have an 06 rifle. I have a 270. I was looking at if I were to stock pile the 06 and ever have a moment to where in the unlikely event that I run out of 45 acp and I am in a pinch, then this would be like a last ditch effort to load some 45's. I understand all of the too time consuming and so on. I would love to find a book on all brass converstions and such. I appreciate everyone's response. It does help me out.
|
December 26, 2008, 11:49 AM | #7 |
Senior Member
Join Date: February 20, 2006
Location: Oklahoma
Posts: 381
|
If you are finding all kinds of brass at the range and the forest floor, you better check first to see if it is boxer brass or Berdan. That presents an entire nuther level of difficulty in reloading if one is not set up for it. Most shooters pick up their boxer brass and leave their berdan stuff lay for others to pick up. If you have a .270, why not convert the '06 brass to shoot in your rifle. That is a much easier task, and just involves necking down a bit. Not a hard job to do even for the most inexperienced.
If I were in possession of that much '06 brass, and it was boxer, you could likely exchange it for 45 ACP brass, which is still very easy to find, for at least a 2 to 1 exchange, and maybe even 3 to 1. ACP brass can still be had for a nickel very easily. Stock up now. |
December 26, 2008, 12:18 PM | #8 |
Senior Member
Join Date: October 11, 2008
Location: Dublin VA
Posts: 105
|
I always check the brass to make sure they are reloadable. I am not running short on any brass by no means. This thread was basically for education purposes for myself. I am just running diffrent scenarios in my head such as what if I ran out of this and I had this then could this work for this and so forth. I knew that 06 could be formed for 270. I knew that you could form one rifle to another. I had no idea that a person could form a rifle to a pistol and found it interesting. I always check for boxer primer pockets and make sure the brass at first glance does not look spit and so forth. Then after polishing using calipers and inspection to make sure I can use unknown brass. I believe one can not get too much information. I really do appreciate your reply. Take care.
|
December 26, 2008, 03:50 PM | #9 |
Senior Member
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
|
Short answer, yes it can be done. The process is cut to length in a trim die, neck ream, finish trim, then develop load data since the book data will not be appicable to your cases. As pointed out repeatedly above, it would be exceedingly time consuming and not worth the effort, since 45 ACP brass is about as common a case as you can find. The same process can be used to make all sorts of brass cases for obsolete cartridges, if you have the form/trim/load dies available.
__________________
Never try to educate someone who resists knowledge at all costs. But what do I know? Summit Arms Services |
December 26, 2008, 06:36 PM | #10 | |
Senior Member
Join Date: June 30, 2000
Location: Token Creek, WI
Posts: 4,067
|
Short answer?
Quote:
Now, if you're just making .45 ACP shotshells, that's a different story. |
|
December 29, 2008, 03:04 PM | #11 |
Member
Join Date: December 10, 2007
Posts: 72
|
Sure.
Yep, it can be done. The "primer end" of a 30-06 (.308, 7mm-08, and a host of others) is the same as the 45 ACP. It's a pain, and certainly not cost effective, but it can be done.
This is the sort of thing you'd resort to if there were, oh, say, an AMMUNITION BAN :barf: or something like that going on. This rates way up there, just short of swaging empty 22 brass around a lead core to make jacketed .224 bullets. That sort of thing was done by enterprising shooters during the Depression and WWII, when components were both expensive and scarce. It could never happen here. Could it? |
December 29, 2008, 09:57 PM | #12 |
Senior Member
Join Date: December 16, 2004
Location: Grand Forks, ND
Posts: 5,333
|
Sell the 30-06 brass, buy 45 ACP brass.
__________________
I don't carry a gun to go looking for trouble, I carry a gun in case trouble finds me. |
December 30, 2008, 01:59 PM | #13 |
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,424
|
One thing that was missed here.....
Large Pistol primers and primer pockets are shorter than their Large Rifle counter-parts. Seating a large pistol primer in a large rifle pocket leads to a recessed primer. Some pistols would probably have trouble detonating the primers. On the flip side- Using a large rifle primer in a cut down '06 / .45 Auto, would cause a noticeable increase in pressure, due to the lower case volume. That is.... IF your firing pin could get past the thicker (harder) primer cup on the LR primer. |
|
|