March 23, 2011, 10:40 PM | #1 |
Senior Member
Join Date: February 16, 2008
Location: Michigan, Upper Pennsula
Posts: 396
|
What is fire lapping?
I have a rifle that is fairly new and the bore is has a dull finish. I have cleaned it with Hoppes 9, Rem Oil, CLP and the bore is still dull and the patched continue to come out with some black. So will fire lapping polish the bore. ( the lands or groves have a dull shine). The rifle is and M1 carbine by Auto Ordince.
__________________
CarpriverShOOter Finch, I don't like guns. Reese, Me either but if someone has to have guns I'd rather it be me. (Person of Interest). No trees were destroyed in the posting of the this message |
March 23, 2011, 11:25 PM | #2 |
Junior member
Join Date: October 6, 2010
Location: Michigan
Posts: 1,080
|
Hello, carprivershooter. Fire lapping is done by forcing an abrasive grit into the surface of a bullet, either lead or jacketed, and firing a with a VERY light charge of fast burning powder. I have done this with an original 1898 Krag rifle, & 1903 Sprgf. The problem is that if not careful..the throat can be lengthened. Also, groove dia. can increase. In my case, the bore was loose about 6" forward of chamber..this was common with turn of century military arms from powder erosion. F.L. cured problem, brightened up bore, even grooves, very very slight taper..measured in tenths of thousand. Accuracy greatly improved.
That said, I don't think you need, or should use such a drastic procedure on your rifle. Have you tried JB compound on a tight patch as per instructions? And after that, some JB Bore Bright..this usually will brighten things up nicely. Just be sure to use a good quality cleaning rod and rod guide. Best of luck! |
March 24, 2011, 01:10 AM | #3 |
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,401
|
Fire Lapping shouldn't be done for cleaning purposes.
Scrub. Scrub. Scrub. As long as the patches are coming out black, that bore is dirty.
__________________
Don't even try it. It's even worse than the internet would lead you to believe. |
March 24, 2011, 02:22 AM | #4 |
Senior Member
Join Date: January 29, 2011
Location: south indiana
Posts: 555
|
it might be that your gun has had molly bullets shot through it or the bore is molly coated
if so its going to take a lot of cleaning |
March 24, 2011, 08:33 AM | #5 |
Senior Member
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
|
How does it shoot? If good, leave alone.
If not accurate, re-read the post by Ideal Tool and follow advice given. |
March 24, 2011, 08:47 AM | #6 |
Senior Member
Join Date: February 18, 2009
Location: SE Michigan
Posts: 558
|
I've done this procedure to a new .22 and a new .50 caliber muzzleloader - they both shoot really great. (The .22 is rediculously accurate at 50 yards). I have a new .204 that I will do this to as soon as I get a small enough rod - good luck.
http://www.centerfirecentral.com/lapbore1.htm
__________________
What direction did that last shot at Kennedy come from? |
March 24, 2011, 09:14 AM | #7 |
Senior Member
Join Date: February 16, 2008
Location: Michigan, Upper Pennsula
Posts: 396
|
thanks for the help
I thank everyone for their comments. I will first try the J B Bore Bright. TFL is a great place to ask questions. There is such wealth of information in this group of people thank you again.
__________________
CarpriverShOOter Finch, I don't like guns. Reese, Me either but if someone has to have guns I'd rather it be me. (Person of Interest). No trees were destroyed in the posting of the this message |
March 24, 2011, 04:17 PM | #8 |
Senior Member
Join Date: June 5, 2000
Location: Job hunting on the road...
Posts: 3,827
|
Doesn't sound like moly...
I'd soak it with a good penetrating oil, and patch it out once a day for a bit... Thing is, it's probably not going to ever be a "shiny" bore unless you screw in a new barrel.
__________________
Job hunting, but helping a friend out at www.vikingmachineusa.com - and learning the finer aspects of becoming a precision machinist. And making the world's greatest bottle openers! |
Thread Tools | Search this Thread |
|
|