The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: General

Reply
 
Thread Tools Search this Thread
Old April 24, 2013, 07:39 AM   #1
trg42wraglefragle
Senior Member
 
Join Date: April 21, 2008
Location: new zealand
Posts: 856
Why heavy bullets in 308?

It seems as though a lot of people are using very heavy bullets in their 308 for long range shooting, generally 166-175gr to get the highest BC possible.

Now Berger's website claims a BC of .515 for their 175gr target bullets.
Sierra's website claims a BC of .504 for their 155gr Palma matchking bullets.

Now I know that Palma rifles have very long barrels to push the lighter bullets much faster, but with such close BC's of the bullets and the ability to push the 155gr bullets faster would it not be better to use the lighter bullets in any barrel length?
Hornadys website claims aBC under .500 for their 178gr A-Max, so wouldn't you be much better off with the lighter faster bullet?

I know that real life can be a lot different than numbers on a computer, but using a JBM ballistics calculator the 155gr doing 2800fps compared to the Berger 175gr doing 2600fps, the 155gr had less wind drift, less drop and retained more velocity.

Am I missing something important, or is it one of those cases when real life is a lot different than on paper?
trg42wraglefragle is offline  
Old April 24, 2013, 08:51 AM   #2
SauerJackson
Senior Member
 
Join Date: March 9, 2011
Location: Minneapolis
Posts: 119
Well, this is just my understanding of it....

But That depends on how far are you really trying to go with it. The lightweight bullets will spin a little faster, and hold a little tighter for a while. But when you really start pushing it out there, say 4, 5,6 hundred yards, it's really going to start getting pushed around in the wind.
A heavier bullet is more resistant to those downrange factors.
SauerJackson is offline  
Old April 24, 2013, 09:17 AM   #3
jmr40
Senior Member
 
Join Date: June 15, 2008
Location: Georgia
Posts: 10,792
Some bullet makers use different methods for measuring BC. If both of those bullets were tested in the same way I'd bet you will see a bigger difference. Compare bullets from the same manufacturer who used the same testing methods and I bet you always see a much higher BC on comparable heavier bullets.
jmr40 is offline  
Old April 24, 2013, 09:23 AM   #4
Old Grump
Member in memoriam
 
Join Date: April 9, 2009
Location: Blue River Wisconsin, in
Posts: 3,144
Depends on your gun too, mine has a fast twist and 185's are more accurate than the 150's. I like accurate and I happily sacrifice fps for retained energy and penetration.
__________________
Good intentions will always be pleaded for any assumption of power. The Constitution was made to guard the people against the dangers of good intentions. There are men in all ages who mean to govern will, but they mean to govern. They promise to be good masters, but they mean to be masters.
--Daniel Webster--
Old Grump is offline  
Old April 24, 2013, 09:45 AM   #5
btmj
Senior Member
 
Join Date: November 1, 2011
Location: Near St. Louis, Missouri
Posts: 864
It also depends on the composition of the bullet. A copper bullet can be the same length and shape as a jacketed lead bullet, but it will be lighter. I don't know if that is what is going on in this case, ..... just say'n....
btmj is offline  
Old April 24, 2013, 09:56 AM   #6
Art Eatman
Staff in Memoriam
 
Join Date: November 13, 1998
Location: Terlingua, TX; Thomasville, GA
Posts: 24,798
I'd load up a box of each and compare the results on Palma-distance targets. That lets me think about pretty girls instead of why manufacturers claim what they do.
Art Eatman is offline  
Old April 24, 2013, 04:20 PM   #7
trg42wraglefragle
Senior Member
 
Join Date: April 21, 2008
Location: new zealand
Posts: 856
Even on Sierras 175gr .30cal bullets have a BC of .505.

I know bullet shape, materials and construction all come into how a bullet will fly, but it would seem all of these things are summed up with one value which is the BC.

Yes barrel twist would come into it, but for some buying a new rifle, would it not be worthwhile getting one to shoot the lighter bullets?

Yes in general a heavier bullet will be better long distance, but its not the bullets weight alone, its that a heavier bullet generally will have a higher BC than a lighter one, but it doesn't automatically mean it'll have a higher BC.

I also plugged all the info into a JBM calculator and using the .505 BC Sierra 175gr compared to .504 BC Sierra 155gr even out to 2000yards the lighter bullet was better.
trg42wraglefragle is offline  
Old April 24, 2013, 06:07 PM   #8
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 18,486
The heavier bullet might be more accurate than the lighter. So if you can read the wind, the higher velocity is no advantage.

Most bullet makers advertise the G1 BC. It is not a great fit for boat tail spitzers but is a larger number than other charts give. Sierra uses the kluge of a "variable" BC by velocity range. Berger also shows the G7 which is a better fit even though a smaller number.
Calculations must be verified by shooting.

Most proficient LR shooters gravitate to the heavier bullets, there must be SOME advantage not apparent from calculations. I have been shooting Scenar 155s and have a hard time telling them from Sierra 175s on the range. But then I am a scratch Sharpshooter and pretty casual competitor.

Of course you are limited to a 156 gr maximum for actual Palma competition.
Jim Watson is offline  
Old April 24, 2013, 06:38 PM   #9
Brian Pfleuger
Moderator Emeritus
 
Join Date: June 25, 2008
Location: Austin, CO
Posts: 19,578
I'm a big fan of light, fast bullets. I almost always use the lightest bullet that will do the job.

Folks talk about 55+ grain 22-250 bullet being "flat shooting". You ain't seen flat until you've seen a 35gr Nosler LF at 4,435fps.

There's another consideration too. Twist rate effects velocity. It's harder to push a bullet in tight rifling. The difference between really tight, like 1:8, versus 1:12 could be a hundred fps.
__________________
Nobody plans to screw up their lives...
...they just don't plan not to.
-Andy Stanley
Brian Pfleuger is offline  
Old April 24, 2013, 09:07 PM   #10
JimPage
Senior Member
 
Join Date: February 21, 2010
Location: Rome, NY
Posts: 941
Generally speaking, the higher the BC the better. But you also have to figure the muzzle velocity. If (exaggerated here) you had a BC of 600 it would be better than the BC 500. But if you can't get the BC 600 going fast enough to start with, the lower BC 500 may be better. So each comparison is different.

Personally for the 30-06 and .308 rifle I have found the BC477 165 grain spire point boat tail bullet to be the most effecient out to about 400 yards, much further than the average hunting shot; but adequate for a long (400yd) shot. That's the max I have ever shot at a deer. Other than a few jump shots close in I have never missed a deer.

Shooter discipline is much more important than BC!!!!!
__________________
Jim Page

Cogito, ergo armatum sum
JimPage is offline  
Old April 25, 2013, 06:31 AM   #11
Bart B.
Senior Member
 
Join Date: February 15, 2009
Posts: 8,927
OK, folks go do some math.

Use ballistic software to compare a Sierra 30 caliber 190 HPMK leaving at 2550 fps (typical NRA match rifle use) against a Sierra 155 Palma HPMK going out at 3000 fps (typical Palma rifle use) then look at the wind drift difference at 1000 yards.

Use some high school trigonometry to figure out the rifling angle different twists present to bullets in different calibers. Most folks are really surprised to learn a 22 caliber 1:8 twist has the same rifling angle to its bullets as a 30 caliber 1:11 twist has to theirs.

Then compare the range of bore and groove dimensions to all the bullet diameters and you my well think there's a greater spread in peak pressure and velocity caused by this than small changes in the rifling's angle to the bullet. I think this is the most common cause.

Last edited by Bart B.; April 25, 2013 at 08:45 AM.
Bart B. is offline  
Old April 26, 2013, 02:16 PM   #12
Tempest 455
Senior Member
 
Join Date: November 17, 2011
Location: TN
Posts: 118
On Sierra's website, they have a PDF charts that shows the BC changes with velocity. They say the 175 SMK have a .505 at 2,800 but less for example if you are at 2650.

http://www.sierrabullets.com/bullets...ient-rifle.pdf

They say the 168's closer to sea level will start to tumble at 1,000 yards and is why most people use the 175's for 1,000 yards.

Last edited by Tempest 455; April 26, 2013 at 02:22 PM.
Tempest 455 is offline  
Old April 26, 2013, 04:29 PM   #13
MTSCMike
Senior Member
 
Join Date: March 15, 2011
Location: Middle TN
Posts: 164
168's go sub-sonic at extreme ranges (900-1000 yards) but the 175's don't. The disruption caused when going sub-sonic can affect accuracy.
__________________
IDPA Member A00640
Founding Charter Member - Middle Tennessee Shooter's Club
MTSCMike is offline  
Old April 26, 2013, 04:45 PM   #14
Jimro
Senior Member
 
Join Date: October 18, 2006
Posts: 7,097
Why don't you go back to JBM ballistics and use the (Litz) data?

That will explain why so many shooters still choose 175 SMKs and heavier VLDs for long range loads.

One of the ways bullet manufacturers sell bullets is by publishing G1 data. G1 data is really useful in comparing flat based spitzer bullets. G7 data is much more useful comparing hollowpoint boat tail bullets. Use the (Litz) data for the Sierra 155 Palma 0.214 G7 and 175 Match King 0.243 G7.

Things make more sense that way.

Jimro
__________________
Machine guns are awesome until you have to carry one.
Jimro is offline  
Old April 26, 2013, 08:07 PM   #15
trg42wraglefragle
Senior Member
 
Join Date: April 21, 2008
Location: new zealand
Posts: 856
Jimro;
That is a very good point, and exactly the answer I was hoping for.
I forgot about G7 BCs as mostly G1's are thrown around.

BUT, Just done a bit of research and with JBM comparing Berger 185gr with G7 of 0.291 doing 2550fps, compared to 155gr Berger G7 0.247 doing 2950fps.
The 155gr will buck the wind better and have less drop out to 1100 yards, and will also have more energy out to 800yards.
After 1100yards the 185gr will buck the wind better, but the 155gr will still have much less drop.

Tis all very interesting this ballistics stuff.
trg42wraglefragle is offline  
Old April 26, 2013, 08:11 PM   #16
trg42wraglefragle
Senior Member
 
Join Date: April 21, 2008
Location: new zealand
Posts: 856
Quite interesting that the G7 of that Berger 155gr Match Hybrid Target is a lot better than the G7's of many 165/168/175gr bullets.

And with G1 numbers how certain light bullets will be a lot higher in a few 155gr bullets than other companies higher grain bullets.

Edit to add:
Also the G7 BC of the .224 90 gr Match VLD Target is 0.281, which according to the data given buy other forums from other shooters is you could get one to around 3000+ fps from a 22-250.

I can't be bothered looking up ballistics at the moment but I imagine it'd be pretty good in the wind.

Last edited by trg42wraglefragle; April 26, 2013 at 08:18 PM.
trg42wraglefragle is offline  
Old April 26, 2013, 09:35 PM   #17
Metal god
Senior Member
 
Join Date: April 10, 2012
Location: San Diego CA
Posts: 6,872
Here is the normal 155gr MK , the BC never gets over .450
http://www.sierrabullets.com/index.c...5&bullettype=0

Here is the 155gr palma MK the BC tops out at .504
http://www.sierrabullets.com/index.c...6&bullettype=0

Clearly there is a design difference in these bullets . I have to assume the palma bullet is longer and that is what gives it the better BC

In the picture of the two bullets next to each other the palma looks a tad longer . You may have to scroll down to the 155gr bullets
http://www.sierrabullets.com/index.c...1&displayAll=1

EDIT : Does anybody know where to find the specs for the OAL of each of these bullets
Metal god is offline  
Old April 27, 2013, 01:06 AM   #18
natman
Senior Member
 
Join Date: June 24, 2008
Posts: 2,604
Quote:
Now I know that Palma rifles have very long barrels to push the lighter bullets much faster, but with such close BC's of the bullets and the ability to push the 155gr bullets faster would it not be better to use the lighter bullets in any barrel length?
Velocity comes and goes, but BC is forever.

In other words, a bit more initial velocity is helpful at first, but after a few hundred yards it's BC that matters in the long run.
natman is offline  
Old April 27, 2013, 05:39 AM   #19
taylorce1
Senior Member
 
Join Date: November 18, 2005
Location: On the Santa Fe Trail
Posts: 8,209
Quote:
Originally Posted by Metal god
EDIT : Does anybody know where to find the specs for the OAL of each of these bullets
JBM Bullet Lengths

0.308 155.0 HPBT MatchKing™ 1.133
0.308 155.0 HPBT Palma MatchKing™ 1.194"
0.308 155.0 Palma [2155] (Litz) 1.131"
0.308 155.0 Palma [2156] (Litz) 1.210"
__________________
NRA Life Member
taylorce1 is offline  
Old April 27, 2013, 09:02 AM   #20
Jimro
Senior Member
 
Join Date: October 18, 2006
Posts: 7,097
trg42wraglefragle,

Ok, here is the "rest of the story" as Mr. Harvey might say...

Those high BC 155gr bullets have a secant ogive to obtain "VLD" numbers, (Very Low Drag). The traditional tangent ogive isn't as "slippery" in the air, but because of how it interfaces with the rifling in the throat is usually much less picky about seating depth.

Everyone I know who is pushing VLDs is pushing them from a custom chamber. Everyone I know shooting a SAAMI spec chamber is pushing a tangent ogive bullet (175 or 190 Match kings).

For example, a 210 VLD with secant ogive has a better BC than the 220 SMK. So why did Crane NSWC choose the 220 with less velocity as the newest 300 Win Mag sniper bullet? Because of how the bullet performs across the entire range of ballistics. The tangent ogive insures that the bullet will perform well in a variaty of chambers across the DOD, and the heavier bullet goes through the transonic range much better than the VLD.

I realize that you are asking about the 308 Win, but Crane NSWC did the same comparitive testing with the new Mk316 Mod 0 version of M118LR, testing multiple bullets looking for accuracy across multiple platforms (m24, M110, M14/21, etc). They stayed with the 175 because it was the most consistent performer as far as accuracy went.

Anyways, Berger recognized that they had a problem with SAAMI spec chambers and came out with their new "hybrid" ogive, which is secant for the bulk of it and then transitions to tangent before getting to the full diameter body of the bullet. This, in theory, allows the benefits of a VLD for high BC with the benefits of a normal BTHP with regard to not being seating depth sensitive. http://www.accurateshooter.com/balli...ogive-bullets/

I hope this explains why a lot of people are sticking with heavier bullets.

Jimro
__________________
Machine guns are awesome until you have to carry one.
Jimro is offline  
Old April 27, 2013, 11:15 AM   #21
JD0x0
Senior Member
 
Join Date: January 30, 2013
Posts: 1,037
Also take into effect the weather conditions. BC becomes much more important as the air gets denser (colder)
JD0x0 is offline  
Old April 27, 2013, 11:29 AM   #22
Metal god
Senior Member
 
Join Date: April 10, 2012
Location: San Diego CA
Posts: 6,872
thanks taylorce1

Your link shows that the 155gr Palma MK is in fact longer then the normal 155gr MK . So it seems we are not comparing apples to apples

EDIT : well I just looked at the 175gr MK and it's longer then the Palma .

Normal 155gr HPBT MK OAL 1.133 - Max BC .450
Palma 155gr HPBT MK OAL 1.194 -Max BC .504
Normal 175gr HPBT MK OAL 1.240 -MAX BC .505

Last edited by Metal god; April 27, 2013 at 11:48 AM.
Metal god is offline  
Old April 27, 2013, 05:24 PM   #23
trg42wraglefragle
Senior Member
 
Join Date: April 21, 2008
Location: new zealand
Posts: 856
Jimro,

That makes a lot of sense, and I can see why the DOD would want to go with the bullet/ammo that will shoot well in any rifle its put into.

That link you gave was very interesting, and I also watched a video that explained a bit more about the new hybrid design, was very informative.

Am I correct in thinking that what you are saying wouldn't really apply to your average shooter who develops a load for one particular rifle and only uses that ammo for that gun?

And the problems you listed with a Secant Ogvie VLD can be solved by using a Berger hybird instead? Or do the Bergers still give up something?
trg42wraglefragle is offline  
Old April 27, 2013, 05:46 PM   #24
Jimro
Senior Member
 
Join Date: October 18, 2006
Posts: 7,097
The average shooter doesn't develop a load for a particular gun. The average handloader will do that, and not every handloader has the skill to really make a rifle sing with a bullet that is really picky about seating depth. Even if a handloader does have the skill, the rifle itself can be an issue if you want other functions like being able to load from the magazine.

I knew a Presidents 100 tab holder who had to change his seating depth every 500 rounds in his service rifle to keep the jump to the lands consistent with the bullets he used for the 600 yard line. That is not a "single load for a single rifle" that is continual load development to ensure maximum accuracy from a rifle as it ages.

Most High Power shooters aren't that picky, but when you are competing for the Presidents 100 tab, then you are competing against other people who are that picky. So then it pays off to use the best bullets perfectly loaded for your rifle. That being said, the AMU is using the 185gr Berger's for their M110 loads for service rifle 1000 yard High Power shooting.

Heck, some top competitors use a meplat uniforming tool which is advertised to take 2% off of the bullet BC, but give much more uniform BC as a result. For those shooters looking to drop from .6 MOA to .5 MOA this is a good thing. For the "average shooter" 0.1 MOA is meaningless.

Anyways, look at the loads that win matches. The only people I know who routinely use the 155gr bullets are Palma shooters for whom the bullet was designed based on international shooting competition rules.

Jimro
__________________
Machine guns are awesome until you have to carry one.
Jimro is offline  
Old April 27, 2013, 07:30 PM   #25
Bart B.
Senior Member
 
Join Date: February 15, 2009
Posts: 8,927
Some years ago, an interesting test comparing Sierra's 30 caliber 190 HPMK against Berger's 185 VLD shooting at 1000 yard target. A chronograph was set up 15 feet from the muzzle of a match rifle and alternate loads of each was fired. 10 feet in front of the 1000 yard target was another chronograph.

Both bullets left the muzzle at about 2570 fps. Their downrange velocity was compared to the velocity at the firing line. At the target, the Berger lost about 50 fps more than the Sierra did.

Go figure that out.
Bart B. is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:21 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.11896 seconds with 10 queries