handloading the 7.62X25 Tok

wolfz · February 24, 2001, 10:52 AM

I want to reload the 7.62X25 Tok. I've found .30 Mauser dies (will these work?) from Lee and RCBS. I've found brass from Starline, and a conversion kit for my Dillon 550B. But I can not find .30cal (.308") 85gr(?) bullets. Any help on any of
these questions and any load data will be greatly appreciated. wolfz

Gewehr98 · February 24, 2001, 12:57 PM

Is it the original Tokarev pistol, Czech CZ-52, the latest batch of PPsh 41 semiauto clone carbines? I'm assuming the Czech CZ-52 pistol. Here's a good place to start, I use the Accurate Arms No.5 data in my Czech CZ-52, with Starline brass and either Sierra 85gr softpoints, or Hornady 90gr XTP hollowpoints. Click on the URL below, hope this helps!

http://users.supernet.com/roo67/reloading.htm

Troy · February 24, 2001, 01:42 PM

Lee has the correct 7.62x25 Tok dies.

http://www.wideners.com carries them, plus the bullets mentioned above.

-Troy

[Edited by Troy on 02-26-2001 at 09:14 PM]

wolfz · February 24, 2001, 03:04 PM

Thanks a lot guys!!

MysDeMeanor · December 4, 2004, 04:36 PM

I have found oodles of load datum for the 30 TOK...all of which give an fps of between 1000 to 1500. Does anyone have any data for the CZ 52 pistol? this gun was made to handle a 'hot' load with a fps of 1400 to 1800. Since I do not have access to a chronograph I have had to resort to 'trial and error' and have had good results with Alliant Power Pistol & Blue Dot powders. Have also used both Speer 100g SPRN and Hornady 90g XTPHP. Prefer the Hornady as they supply the same style bullet in 124g for the 9mm Largo barrel I also use in the CZ 52. (rechambered 9mm Luger barrel from Fed.Arms)

February 24, 2001, 12:57 PM	#2
Gewehr98 Senior Member Join Date: June 30, 2000 Location: Token Creek, WI Posts: 4,067	What gun are you reloading it for, Wolfz? Is it the original Tokarev pistol, Czech CZ-52, the latest batch of PPsh 41 semiauto clone carbines? I'm assuming the Czech CZ-52 pistol. Here's a good place to start, I use the Accurate Arms No.5 data in my Czech CZ-52, with Starline brass and either Sierra 85gr softpoints, or Hornady 90gr XTP hollowpoints. Click on the URL below, hope this helps! http://users.supernet.com/roo67/reloading.htm

December 4, 2004, 04:36 PM	#5
MysDeMeanor Junior Member Join Date: December 4, 2004 Posts: 4	CZ 52 loads I have found oodles of load datum for the 30 TOK...all of which give an fps of between 1000 to 1500. Does anyone have any data for the CZ 52 pistol? this gun was made to handle a 'hot' load with a fps of 1400 to 1800. Since I do not have access to a chronograph I have had to resort to 'trial and error' and have had good results with Alliant Power Pistol & Blue Dot powders. Have also used both Speer 100g SPRN and Hornady 90g XTPHP. Prefer the Hornady as they supply the same style bullet in 124g for the 9mm Largo barrel I also use in the CZ 52. (rechambered 9mm Luger barrel from Fed.Arms)

February 24, 2001, 10:52 AM	#1
wolfz Senior Member Join Date: October 13, 1998 Location: Chandler, Az, USA Posts: 125	I want to reload the 7.62X25 Tok. I've found .30 Mauser dies (will these work?) from Lee and RCBS. I've found brass from Starline, and a conversion kit for my Dillon 550B. But I can not find .30cal (.308") 85gr(?) bullets. Any help on any of these questions and any load data will be greatly appreciated. wolfz

February 24, 2001, 01:42 PM	#3
Troy Member Join Date: January 29, 2000 Posts: 96	Lee has the correct 7.62x25 Tok dies. http://www.wideners.com carries them, plus the bullets mentioned above. -Troy [Edited by Troy on 02-26-2001 at 09:14 PM]

February 24, 2001, 03:04 PM	#4
wolfz Senior Member Join Date: October 13, 1998 Location: Chandler, Az, USA Posts: 125	Thanks a lot guys!!