|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
November 14, 2015, 09:11 AM | #1 |
Junior Member
Join Date: November 24, 2014
Posts: 2
|
Federal shells versus others
I have a chart from an older magazine that shows case capacities for 7 brands of shells. Federal shells have the thickest walls next to military ones. I bought 500, once fired Federal shells for $50.00 from a police sniper friend that I want to reload. Does anyone have recommendations on load reductions when using Federal in place of Remington or Winchester shells. My loads would be towards the lower velocities listed in reloading books. Examples: 150gr at 2600fps
|
November 14, 2015, 09:41 AM | #2 |
Senior Member
Join Date: August 23, 2014
Location: Nevada/Ariz/CA
Posts: 1,753
|
It sounds like you are talking about once fired .30-06 Federal cases, my favorite, and at a good buy. From a loading manual you could start by splitting the difference between start and max loading (or lower yet). The thicker brass on the Feds provides tighter case neck tension than most other brands but some report, myself included, that primer pockets may tend to loosen sooner than other brands. That would depend on the loading and may not occur with reduced loads of course. I consider the heavier Feds to be preferable over most others, whether rifle or handgun.
__________________
Ouch, the dreaded "M-1 thumb", you just know it will happen eventually, so why not do it now and get it over with?? Last edited by condor bravo; November 15, 2015 at 10:57 PM. |
November 14, 2015, 10:56 AM | #3 |
Senior Member
Join Date: January 5, 2009
Location: Just off Route 66
Posts: 5,067
|
Here is an idea from Greek history. With an eye dropper fill both a Federal case with water and another brand such as Winchester the same way. Then put the water from each into a test tube and measure the VOLUME difference.
As an example if the volume of the Winchester case is 0.55 ml and the volume of the Federal case is 0.51 ml then the volume difference would be 7.28 %. A 10 % reduction of powder with the Federal case should give an approximately same pressure as the Winchester case. Hope that helps. Jim http://www.amazon.com/Piece-Pyrex-Gl...rds=test+tubes
__________________
Si vis pacem, para bellum Last edited by Jim243; November 14, 2015 at 11:15 AM. |
November 14, 2015, 11:26 AM | #4 |
Senior Member
Join Date: September 15, 2005
Location: Oregon
Posts: 1,033
|
Federal is my preference as well for my bolt rifles. You won't need to reduce a starting load found in a load book, if that is what you're asking. The difference isn't usually that great, but does matter if you had an upper end load you had worked up in one brand case then switched to another. In that instance I would back off a couple grains and work it back up like I did initially. But if you're starting an initial workup for a load that will use a Federal case, you don't need to change anything.
|
November 14, 2015, 02:23 PM | #5 | |
Senior Member
Join Date: July 18, 2008
Posts: 7,249
|
I have Federal cases, I have military surplus cases, I have Federal military cases, I have Federal cases that are stamped TW.
Quote:
Caution: I am so a fan of Federal primers, and I do like the big trays Federal uses. And I heard the story about the Fred Rex driver that blew his tail gate off with those most powerful primers. F. Guffey Last edited by F. Guffey; November 15, 2015 at 11:45 AM. Reason: replace a g with a t |
|
November 14, 2015, 02:58 PM | #6 |
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
|
Your magazine must be really old. Federal brass is well known for being softer than other brands. Case capacity has nothing to do with hardness though. And Federal being softer only means it doesn't last as long. No need to reduce the load for Federal brass
TW is Twin Cities Ordnance Plant, Minneapolis, MN. Federal operated it until 1946.
__________________
Spelling and grammar count! |
November 14, 2015, 04:17 PM | #7 |
Senior Member
Join Date: April 10, 2012
Location: San Diego CA
Posts: 6,876
|
When I'm starting a new I start at minimum charge regardless of what case I'm using . If I'm changing from one head stamp to another in a load I already have . I drop the charge 1.5gr and work back up . Maybe if you're using a large magnum case you drop the charge 2.5gr . I don't weigh my cases because after reading many things about case capacity . It seems there is no direct correlation to case weight and case volume . It just seems easier to drop the charge some and work back up then doing all those weighing and water test .
If you do the water test I've read you should use fully fire formed case to your chamber . Also be sure all case are trimmed to the same length . This give you a true volume value to the particular chamber the case will be fired in.
__________________
If Jesus had a gun , he'd probably still be alive ! I almost always write my posts regardless of content in a jovial manor and intent . If that's not how you took it , please try again . Last edited by Metal god; November 14, 2015 at 04:23 PM. |
November 14, 2015, 05:04 PM | #8 | |
Senior Member
Join Date: September 6, 2013
Location: JAX, FL
Posts: 377
|
Federal brass is junk???
just for ghee-whiz info I recall reading something Dan Newberry wrote about brass choices in his explanation of his OCW (Optimal Charge Weight) load development process. As I recall he described Federal brass as undesirable for truely accurate loads.
just looked into my favorites and found the link to his site. As it turns out his mention of Federal brass was not in his discussion or instruction pages but rather a note for his personal pet loads. http://optimalchargeweight.embarqspa...pes/4533485759 Quote:
__________________
“Some people spend an entire lifetime wondering if they made a difference in the world. But, the Marines don't have that problem.” ― Ronald Reagan |
|
November 14, 2015, 05:08 PM | #9 |
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,424
|
Don't overthink the perceived problem.
Just start low and work up. Standard starting loads should be perfectly safe and sane in anything but lathe-turned cases. --- Like some other members, and a few comments here... I also don't consider most Federal rifle cases to be suitable for reloading. The brass doesn't play nicely, and the primer pockets are often toast after the first firing (factory load). I think the most loadings I've ever gotten with Federal rifle cases was three (factory, plus two reloads) with .270 Win and a mild load. Some reloaders claim much better luck with Federal brass, but it hasn't worked out for me. *.223 Rem / 5.56x45mm is an exception. It seems to be drawn with a different alloy than Federal's other cartridge cases. Don't be afraid to use the brass, but be aware that you may encounter loose primer pockets, or other issues that result in having to throw away a portion of what you bought.
__________________
Don't even try it. It's even worse than the internet would lead you to believe. Last edited by FrankenMauser; November 14, 2015 at 05:14 PM. |
November 14, 2015, 07:22 PM | #10 |
Senior Member
Join Date: April 10, 2008
Location: Alaska
Posts: 7,014
|
Like he said
|
November 14, 2015, 08:46 PM | #11 |
Senior Member
Join Date: August 23, 2014
Location: Nevada/Ariz/CA
Posts: 1,753
|
I've never encountered a single once fired Fed '06 case with a loose primer pocket so I don't think the OP has any concerns about losing part of his investment, especially since he seems to be favoring mild loads. Yes loose pockets can show up after a few loadings, certainly more than just one or two, but when used with the Garand most of your cases have been lost before loose primer pockets become an issue. At 500 per $50 I would take all I could get even if I could get only two loads from them. Loose primer pockets with Fed '06 brass not hardly a concern. When encountered during reloading, I deprime and put the cases aside for metal recycling.
__________________
Ouch, the dreaded "M-1 thumb", you just know it will happen eventually, so why not do it now and get it over with?? Last edited by condor bravo; November 14, 2015 at 08:52 PM. |
November 14, 2015, 11:01 PM | #12 | |
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,424
|
Quote:
(I use quotation marks around .30-06 because .270 Win and .280 Win are both derivatives of .30-03, not .30-06. Like .35 Whelen, they require the longer neck of .30-03. So, they're more 'brothers' to .30-06 than offspring.)
__________________
Don't even try it. It's even worse than the internet would lead you to believe. |
|
November 14, 2015, 11:31 PM | #13 |
Junior member
Join Date: April 22, 2014
Location: Washington
Posts: 1,549
|
I use mixed head stamp cases for everything but I separate my cases and then weigh the cases. Once I have established the head stamp that is the heaviest meaning the least volume I use those cases to work up my load using that minimum volume case as the standard. If I pick up some cases of a different head stamp which is unlikely I weigh them so I know if I am dealing with a lesser case volume or not. As long as the case volume is the same or larger then I am good to go with the load{s} that I have worked up.
|
November 15, 2015, 07:59 AM | #14 |
Senior Member
Join Date: July 26, 2015
Posts: 526
|
I had some 243W Fed brass that I reloaded a couple times. Firing the 3rd reload (factory load+3 reloads so 4 loadings) on those cases made me think I had shot my barrel out, accuracy was heading downhill...FAST. Later, at home, I looked down my barrel and all appeared normal. I inspected the cases and found the inside of the necks looked like someone filed them out with a rasp . I've got Hornady brass that doesn't show any deterioration like that in a similar # of reloads. Perhaps the Federal brass produced 30+ years ago was better. The current production is only good for that one loading IMO.
|
November 15, 2015, 11:50 AM | #15 |
Senior Member
Join Date: July 18, 2008
Posts: 7,249
|
And no one measures the diameter of the case head before firing.
I have fired cases once and got all the use out of them that was possible. F. Guffey |
November 15, 2015, 12:17 PM | #16 |
Senior Member
Join Date: November 5, 2000
Location: Wyoming
Posts: 1,761
|
I cannot speak directly to Federal 30-06 cases because I haven't used them, but I did use Federal 308 cases, and for the most part they did okay so long as I didn't firewall the load. When I did load at max charges, the cases lasted 3-4 firings before the primer pocket was noticably looser.
These days I am not much on once fired cases for my rifles, just a personal preference. With brand new cases I take careful measurements of the case head, length and such so I can keep track of them closely. |
November 15, 2015, 04:28 PM | #17 |
Senior Member
Join Date: September 2, 2010
Location: Plainview , Long Island NY
Posts: 3,863
|
I like federal brass. Drop your load by 1.0 grains from listed load tables. I also reload on the light side. 308 cal using a 168 gr. Sierra HPBT bullet over 40.5 - 41.5 gr. over IMR 4064 200 yard zero very accurate with a .001 jump with .001 headspace. That's for a bolt action Remington 700 trued setup.
|
November 15, 2015, 10:47 PM | #18 | |
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,424
|
I fixed this for you, F. Guffey:
Quote:
__________________
Don't even try it. It's even worse than the internet would lead you to believe. |
|
November 16, 2015, 09:23 AM | #19 | |
Senior Member
Join Date: July 18, 2008
Posts: 7,249
|
Quote:
F. Guffey |
|
November 16, 2015, 11:23 AM | #20 |
Senior Member
Join Date: July 8, 2013
Location: Littleton, Colorado
Posts: 1,121
|
So, if Federal cases are slightly thicker, is there a concern about pressure like we've heard about 5.56 cases?
|
November 16, 2015, 02:23 PM | #21 |
Senior Member
Join Date: September 2, 2010
Location: Plainview , Long Island NY
Posts: 3,863
|
Full sizing your brass the round will fit your chamber, the inside of the case has less volume, so lower your listed charge by one grain & you'll be safe.
|
November 16, 2015, 11:42 PM | #22 | |
Senior Member
Join Date: September 15, 2005
Location: Oregon
Posts: 1,033
|
Quote:
|
|
|
|