|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
December 26, 2010, 01:46 PM | #1 |
Senior Member
Join Date: February 24, 2010
Posts: 498
|
Walnut stock: free float or full-length bed?
I'm fitting a replacement walnut stock to a rifle. What is the general consensus (if there is one) on which method is most accurate? Should I bed the action and float the barrel, or should I bed the entire length?
Thanks for any info. |
December 26, 2010, 01:52 PM | #2 |
Senior Member
Join Date: December 19, 2008
Location: milton, wv
Posts: 3,640
|
Like mine Floating
__________________
Desert Eagle Alliance Group Launcher Extraordinaire ______ ----Get Busy Live'n.....Or....Get Busy Die'n......Red -------They call me Dr. Bob,,,, I have a PhD in S&W |
December 27, 2010, 06:09 PM | #3 |
Senior Member
Join Date: March 11, 2010
Location: South East Pa.
Posts: 3,364
|
It has been my experience that free-floating a standard weight barrel in a wood stock will cause more problems than it solves. Also, if you bed the whole thing, use a good solid epoxy. Some "bedding" material that is sold turns out like hard rubber when cured.
|
December 27, 2010, 07:28 PM | #4 |
Senior Member
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
|
Use good bedding material, and free float the barrel.
__________________
Never try to educate someone who resists knowledge at all costs. But what do I know? Summit Arms Services |
December 27, 2010, 08:29 PM | #5 |
Senior Member
Join Date: July 27, 2009
Location: Ft. Polk
Posts: 883
|
A properly bedded rifle is the most accurate, its also the most expensive way to go, which is why free floating became so popular. But with a wooden stock its going to move and shift with temperature and humidity changes... So free floating might be best if you plan on using this rifle year round. But even free floating has problems if not properly done. Without proper clearance down the length of the stock you can have pressure points along the barrel where it touches the stock, which can throw off accuracy. Some people use the credit card trick when this happens. To adjust the pressure point. Mcmillian does full length epoxy glass bedding, and they're pretty renown for their stock work, might want to look them up because there used to be a lot of good info on their site, been awhile since I've checked it out though.
__________________
Freedom's just a word. If I'm gonna die for a word, my word is jello... |
December 28, 2010, 05:07 AM | #6 |
Senior Member
Join Date: June 24, 2008
Posts: 2,607
|
Bed and float.
|
December 28, 2010, 09:09 AM | #7 |
Senior Member
Join Date: June 14, 2004
Location: NY State
Posts: 6,575
|
Mine are all fully bedded receiver +2" of barrel , with the rest of the barrel floated. This is what we were taught in gunsmithing school. Accuracy and POI are the same 35 years later !!
__________________
And Watson , bring your revolver ! |
December 31, 2010, 11:00 AM | #8 |
Member
Join Date: October 11, 2010
Location: SE Michigan
Posts: 68
|
I've always free floated my rifles where possible. That said, I glass the entire barrel channel and have a couple layers of masking tape applied to the barrel, back to about 2" in front of the chamber. The full length glassing in of the barrel channel keeps the wood from warping. Looks good, shoots even better.
__________________
"It is the province of knowledge to speak and it is the privilege of wisdom to listen".... Oliver Wendell Holmes |
January 1, 2011, 02:45 PM | #9 |
Senior Member
Join Date: March 11, 2010
Location: South East Pa.
Posts: 3,364
|
Best to think what you are going to do with that rifle before deciding how to bed it. I suspect most of the people for floating a barrel are open country hunters or out west hunters. If you hunt mountainous, thick areas where you are constantly getting grit and dirt under the barrel, I would think about solid bedding that barrel. Old model 70's are so tight that it looks like the tree grew around the barrel and most shot quite well. If you do go with a solid bed, it is best to have a screw in the fore arm attaching it to the barrel.
|
|
|