March 28, 2013, 08:24 AM | #1 |
Senior Member
Join Date: January 12, 2012
Location: Upstate SC
Posts: 223
|
Mauser question w/pics
I just bought a Mauser .308 cal with a turned down bolt. I know it's a conversion I just need to know what model it is. It has no markings that I can find yet. There is a large bolt through the fore-end like Ive seen on other rifles. The shop where I got it didn't know what model as they had 2 in 308 and both were different. The magazine follower has a taper at the rear so that after the last round you can still close the bolt without depressing the follower, the other mauser didn't have that. The rear sights were both different wood hand guard in front and behind the rear sight and no bolt at the rear of the stock and the other didn't have the bolt through the stock and the magazine bases were different. The Front sight on mine has a circular guard open on the top. Any idea what it is? Or how I can tell what it is.
Last edited by gasmandave; March 28, 2013 at 07:03 PM. |
March 28, 2013, 09:37 AM | #2 |
Senior Member
Join Date: May 27, 2007
Posts: 5,261
|
Will need pictures.
Go to a free internet picture site, like Photobucket, get an account and upload the pictures. If this was a car site your post would read: "I have a car, it has four wheels, the trunk is big, it has been repainted, tapered in the front, can you tell me what model it is?" Ah, no.
__________________
If I'm not shooting, I'm reloading. |
March 28, 2013, 09:46 AM | #3 |
Senior Member
Join Date: January 12, 2012
Location: Upstate SC
Posts: 223
|
"I have a car, it has four wheels, the trunk is big, it has been repainted, tapered in the front, can you tell me what model it is?" So can you help me with my car too! Cool you guys are great! Seriously This post is useless without pix...The rifle is at home and I'm not. Will have to post a picture later.
|
March 28, 2013, 11:10 AM | #4 |
Member
Join Date: February 20, 2013
Posts: 16
|
Measure the bolt If its 7&1/2 inches long you have a Yugo M48bo
|
March 28, 2013, 07:27 PM | #5 |
Senior Member
Join Date: January 12, 2012
Location: Upstate SC
Posts: 223
|
Bolt is a tad over 6 3/4"
|
March 28, 2013, 08:09 PM | #6 |
Senior Member
Join Date: June 22, 2009
Location: South Carolina
Posts: 203
|
Looks like a Chilean 308 conversion a little bit. Is there writing on left side of receiver like Modelo ??????
Don't change a thing on it, leave it just like it is. Nice condition to boot.
__________________
Distinguished Rifleman High Power & Smallbore Prone President's Hundred (Rifle) US Palma Teams(2) US Dewar Team (2),4 Man Natl.Champ Team SB Prone Cert Test Dir. Sm Arms and Ammo,Aberdeen Pr Ground, Firefighter I, AC4HT |
March 28, 2013, 08:17 PM | #7 |
Member
Join Date: February 20, 2013
Posts: 16
|
Appears to be a small ring mauser Spain when they joined NATO had there 7mm mausers redone to use NATO 7.62x51 rounds or .308 Years ago I had a sporterized one and killed many a hog with it Hopes this may help
|
March 28, 2013, 08:20 PM | #8 |
Senior Member
Join Date: November 27, 2005
Posts: 1,419
|
Just don't shoot standard commercial .308 through it, the small ring Mauser can't handle the pressure very well.
|
March 28, 2013, 08:32 PM | #9 |
Senior Member
Join Date: January 12, 2012
Location: Upstate SC
Posts: 223
|
What do you mean "Don't shoot standard 308 through it...they don't handle it well" Does it mean it will blow up or just rattle loose? I have 4 boxes of mil sup ammo and 3 boxes of Winchester power points.
|
March 28, 2013, 08:38 PM | #10 |
Senior Member
Join Date: September 19, 2012
Location: Near Gainesville Fl.
Posts: 224
|
Site
__________________
Criminals obey gun laws in the same way politicians follow their oaths to office - Anonymous It's better to be silent and called a fool, than to speak and remove all doubt |
March 28, 2013, 08:43 PM | #11 |
Senior Member
Join Date: November 27, 2005
Posts: 1,419
|
I'm just saying the small ring Mausers were originally chambered in cartridges like 6.5x55 and 7mm mauser, the 7.62x51 has a good bit more pressure than those old cartridges, and commercial ammo is loaded even hotter than the Nato.
On top of that the small ring Mausers don't have a reputation of being very strong and pressure friendly, there are several cases of small Mauser actions blown up by commercial .308. Collectors shooting this rifle mostly use their own slightly downloaded reloads, and that would be my advice as well. |
March 28, 2013, 08:56 PM | #12 | |||||
Senior Member
Join Date: May 27, 2007
Posts: 5,261
|
I agree it is a small ring Mauser and if it is in 308 it has been converted.
The problems with these 308 conversions is that the 308 operates at much higher pressures than original, and I mean pre 1898, 7mm Mauser cartridges. Also the date of your receiver is unknown if the ring stampings have all been ground off. Ludwig Olsen was a real Mauser expert and described the proof loads for pre WW1 Mauser M98 actions in “Rifle Magazine” Issue 159 May 1995 Dear Editor pg 10 What you notice is even these early M98 mausers were proofed at pressures that are about equal to the normal operating pressures of 308 Winchesters. Constant shooting of full power 308 loads would be a severe strain on an early receiver. Ludwig Olsen Mauser 98 actions produced by Mauser and DWM were proofed with two loads that produced approximately 1000 atmosphere greater pressure than normal factory rounds. That procedure was in accordance with the 1891 German proof law. Proof pressure for the Mauser 98 in 7 X57 was 4,050 atmospheres (57, 591 psi). Pressure of the normal 7 X 57 factory load with 11.2 gram bullet was given in Mauser’s 1908 patent boot as 3,050 atmosphere, or 43, 371 pounds. While many Mausers in the 1908 Brazilian category will likely endure pressures considerably in excess of the 4,050 atmospheres proof loads, there might be some setback of the receiver locking shoulder with such high pressures. http://www.riflemagazine.com/magazin...159partial.pdf Spanish Mausers gained an unfortunate reputation because enough accounts have surfaced about the inconsistent metallurgy and heat treatment of these actions. It is a gamble when dealing with Spanish Mausers: Excessive Headspace in M1916 Mauser http://www.thehighroad.org/showpost....9&postcount=10 Quote:
Quote:
http://dutchman.rebooty.com/1895Chile.html Even the vaunted small ring Swedish actions have issues: http://castboolits.gunloads.com/show...low-up-project Variation in M96 Swede Actions Quote:
Quote:
I doubt the military barrel will shoot as well as my Krieger, but my recommended load is very accurate. Twenty shots for record in a 100 yard reduced Highpower match, iron sights, prone with a sling.
__________________
If I'm not shooting, I'm reloading. Last edited by Slamfire; March 29, 2013 at 08:31 AM. |
|||||
March 28, 2013, 09:10 PM | #13 |
Member
Join Date: December 1, 2010
Posts: 66
|
Your Mauser
Looks like a Spanish Mauser. I bought one imported by Samco that was rebarreled at the factory in Spain. The "Numrich Military Firearms Reference Guide" will have a lot of Mauser info. The guide comes with their Commercial Firearms Reference Guide. (a 3 catalog set that gives a lot of info, pictures and parts available.) The book says the 308 is a model 1916
|
March 28, 2013, 09:39 PM | #14 |
Junior member
Join Date: February 2, 2010
Posts: 6,846
|
It is a "1916" Mauser. I've seen these with both 93 and 95 bolts. Another quirk noticed is that some of the actions had been cut back at the front ring. Apparently, this was done to facilitate rechambering/reboring the 7x57 to 7.62x51(.308). I've found a couple of these actions with this front ring cut back while others were not. I have one laying on the shelf that the customer brought in to be rebarrelled with a ready to install barrel. Unfortunately, the threaded barrel shank is about .1" longer than the threads inside the front action ring.
|
March 30, 2013, 08:05 AM | #15 |
Senior Member
Join Date: January 12, 2012
Location: Upstate SC
Posts: 223
|
Well thanks for all the info, wish I had this before I bought the rifle. Went back to the place where I got it and asked the guy if he knew about what it was and about the ammo issue. He said he did. He never mentioned it to me the time of purchase. He took the rifle back no questions about it. He knows me pretty well and was going to give me my money back. I do business there a lot so I just took a store credit to use later.
|
March 30, 2013, 09:54 AM | #16 |
Senior Member
Join Date: September 19, 2008
Posts: 4,678
|
That dealer is certainly an upstanding gentleman - my hat's off to him.
So many dealers are bad-mouthed, that I would suggest you post the name of his business here, even though he might well have advised before the sale that the rifle was a "handloading only" proposition. FWIW, if you're looking for a Mauser, in a modern chambering that has a higher operating pressure than the original design chambering, I would suggest only looking at "cock-on-opening" Mauser 98's, and forget any "cock-on-closing" earlier Mauser designs. . |
March 30, 2013, 09:58 AM | #17 |
Senior Member
Join Date: November 27, 2005
Posts: 1,419
|
I don't know, I think it was quite irresponsible to sell this milsurp gun without warning the buyer of the danger of shooting regular ammo through it.
|
March 30, 2013, 10:00 AM | #18 |
Senior Member
Join Date: September 19, 2008
Posts: 4,678
|
Maybe - I was cutting the dealer some slack, on the premise that he might have thought the OP a buyer knowledgeable in that area.
. |
March 30, 2013, 06:27 PM | #19 | |
Senior Member
Join Date: September 10, 2007
Location: Racoon City
Posts: 934
|
Quote:
__________________
_____________________________________________ Questions about 7.62 NATO and 308 Winchester? Click here. |
|
March 30, 2013, 08:47 PM | #20 |
Senior Member
Join Date: January 12, 2012
Location: Upstate SC
Posts: 223
|
The gun shop owner is a good man, never gouges anyone always fair in his dealings. When I asked him about the rifle if he knew about the ammo issue I got the impression that he just forgot to tell me. I've done business with Lee for about 16 years and he has always been fair. Not to just me but everyone. His name is Lee Barrett and he owns Barretts trading post in Westminster SC.
|
March 31, 2013, 10:47 PM | #21 |
Senior Member
Join Date: August 13, 2011
Location: Seattle area
Posts: 661
|
I think when those mausers were converted, it was for 7.62 CETME (or something like that) which was a lower pressure than the NATO stuff.
I believe the CETME round is about 45,000 psi = 37,000 cup which is in the same category as the original 7x57 mauser pressures; I think the 7.62 NATO/308 Winchester is in the 60,000 psi = 52,000 cup, which is certainly to high for one of those Spanish mauser actions, it might not blow up, but high pressure use, could set the lugs back or stretch the action and/or chamber. Someone who knows for sure will chime in. Last edited by tahoe2; April 3, 2013 at 05:28 PM. |
March 31, 2013, 11:35 PM | #22 | |
Senior Member
Join Date: July 10, 1999
Location: High Desert NV
Posts: 2,850
|
Quote:
.308 Win is rated at 62,000 psi. 7.62x51 is rated at 60,200 psi. Not a lot hotter, but hotter it is. If it passed headspace, I would not be afraid of it, but I would also reload to middle of the road 300 Savage pressures, which would be on par with the original 7X57 pressure the rifle was built for. |
|
April 1, 2013, 03:20 AM | #23 | |
Senior Member
Join Date: September 10, 2007
Location: Racoon City
Posts: 934
|
Quote:
__________________
_____________________________________________ Questions about 7.62 NATO and 308 Winchester? Click here. |
|
April 1, 2013, 08:28 AM | #24 | ||
Senior Member
Join Date: May 27, 2007
Posts: 5,261
|
Quote:
__________________
If I'm not shooting, I'm reloading. |
||
April 1, 2013, 11:54 AM | #25 | |
Senior Member
Join Date: July 10, 1999
Location: High Desert NV
Posts: 2,850
|
Quote:
So do you want to use ammo that is ~4000PSI (~7%) over the design max, or ~5500PSI (~10%) over the design max? Me, I would load down to the ~50Kpsi range. Still plenty to kill just about anything in North America. |
|
|
|