November 26, 2012, 08:16 AM | #1 |
Senior Member
Join Date: February 15, 2011
Location: Gods waiting room.
Posts: 103
|
M&P Trigger job
I'm not sure if this is the right spot for this. but here it goes.
A little backstory on me. I've always been into taking things apart and putting them back together. I would say I have a 99.9% success rate on all things. 100% on firearms. I have dissemblance almost every firearm I own, more than once. Including a Sig Sauer Mosquito! I'm a computer tech by trade and I'm used to pulling laptops apart. So the small and intricate parts of a firearm are nothing new. Now, on with my question Someone asked me if I'd swap out a ghost trigger on his M&P9. I happen to have one at home. This weekend I did take out the trigger assembly and found the sear and all that jazz. So I have a good idea of what a 'trigger job' has in store but whats the going rate for such a job? I know I wouldn't be able to charge was a 20+ year exp gunsmith would, but I'm not going to do this for free either. Hell, I may be barking up the wrong tree all together. Either way, let me know what your experiences have been. Thanks guys.
__________________
Glock 26 | Glock 36 | Glock 17L | Ruger LCP | Llama .38spc | NEF 10 gauge | NEF 20 gauge pump | Savage Mark II GL |Remington 770 | Remington 30/30 | Remington 25/35 | |
November 26, 2012, 08:50 AM | #2 |
Senior Member
Join Date: August 27, 2011
Location: western Iowa
Posts: 205
|
Sorry if I seem a bit harsh here but there is no way I would pay you anything to do your first trigger job on MY gun. I also work on computers, computers are plug and play, replace broken components, etc. No "smithing" involved. Matter of fact, I won't let the local "gunsmith" touch my gun (sorry Bubba), but I'm less than 100 miles to Cylinder & Slide.
I may back off my assessment if you can list here both the steps and the tools (Brownell cat. numbers a bonus) to do a trigger job on an M&P9. Work on your own guns if you must but from the perspective of liability alone I would not touch another person's pistol without training, tools and insurance (that's why a smith charges so much, not because he can but because he must, to stay in business). I do work on my own guns, doing a sight swap and Wolfe spring swap on my Sig Sauer P6 this week, but that's a far cry from a "trigger job". |
November 26, 2012, 04:33 PM | #3 |
Senior Member
Join Date: February 15, 2011
Location: Gods waiting room.
Posts: 103
|
By working "On computers" Do you mean your work is ON computers. Like, say, a modern day photographer?
No cupcake. Computers are not as plug and play as you might think. Try replacing a hdd on a netbook or a the cooling fan on a laptop. Or a motherboard on any computer. Ever dive into an iMac? The guy asked me if I was a gunsmith. I said no. But I said I had a M&P at home and I would take that down and see what all was involved and I'd get back with him. He seemed ok with the notion. I would, of course, have him sign a waiver saying that neither me nor the range I work for would be responsible in any way if something were to happen to him or his firearm. That being said, I did take mine down. I did take the trigger group out. I did remove everything as well as getting it all back together. Guess what? It still works. This is not my first trigger job. Like I said, I have already disassembled my m&p and I've worked on quiet a few glocks. Granted, glocks are mindlessly simple. Point is, its not my first time taking a gun apart. Some people are afraid to take things apart. I can understand them to a point. So its ok if you're not comfortable working on things. But I'm just wondering. You wouldn't do your own trigger, but you also wouldn't let a gunsmith do one either. So how would you possible give me any insight? Either way, your triggers will never be touched from the inside. I'm not going to be forging my own parts in a kiln. The guy is going to bring me a drop in trigger kit. There's no "smithing" involved. Take out pins, remove take down lever, remove trigger assembly. Replace parts. Reassemble. 080-000-651wb 080-000-019wb 956820
__________________
Glock 26 | Glock 36 | Glock 17L | Ruger LCP | Llama .38spc | NEF 10 gauge | NEF 20 gauge pump | Savage Mark II GL |Remington 770 | Remington 30/30 | Remington 25/35 | |
November 26, 2012, 05:05 PM | #4 |
Senior Member
Join Date: July 1, 2011
Location: Texas, land of Tex-Mex
Posts: 2,259
|
I would not put a trigger into another person's firearm, for liability reasons alone.
Firearms are an extremely target rich environment for risk. You're setting yourself up for a lawsuit for no real reason. Let the professionals do such. I'd politely back track and denote you're not comfortable with this as you're not skilled in the area and you don't want anything to happen to the guy. |
November 26, 2012, 06:48 PM | #5 |
Senior Member
Join Date: February 15, 2011
Location: Gods waiting room.
Posts: 103
|
Sound advice, ill most likely take you up on that. thank you.
__________________
Glock 26 | Glock 36 | Glock 17L | Ruger LCP | Llama .38spc | NEF 10 gauge | NEF 20 gauge pump | Savage Mark II GL |Remington 770 | Remington 30/30 | Remington 25/35 | |
November 26, 2012, 08:08 PM | #6 |
Senior Member
Join Date: August 27, 2011
Location: western Iowa
Posts: 205
|
Working on computers
No "cupcake". I build computers, replace harddrives, upgrade memory, and have replaced the lcd's, cooling fans, cpu fans, etc. in laptops. I built/restored a Mac from the motherboard up from components I acquired from several different sources, without a schematic. I have taken two different Laser printers using the same engine and made a working Apple Laserwriter II from parts of a Laser Writer and an HP Deskjet (both use the same Canon engine). I have been inside computers for more than twenty years, I've cracked the case on more than one Mac Classic to replace drives and memory.
I also work on computers, Photoshop mostly. I was a level two tech support at Gateway. The only thing more difficult than troubleshooting a computer on the bench in front of you is troubleshooting a computer over the phone. I have machines at home running different dialects of Linux and Microsoft Windows. All of that is infinitely easier than stoning the sear on a trigger group just enough to smooth the trigger without turning it full auto. I still wouldn't let you or my local bubba work on my pistols. Swapping out a trigger group is not smithing. My point was and is, I consider the local "smith" to be incompetent, I've seen his work and I'm less than 100 mines from Cylinder and Slide, Bill and his crew know what they are doing. |
November 26, 2012, 09:03 PM | #7 |
Senior Member
Join Date: June 24, 2012
Posts: 1,055
|
" but I'm not going to do this for free either"
You must have an FFL to perform gunsmithing services,no mention of that well known fact. |
November 26, 2012, 09:35 PM | #8 |
Senior Member
Join Date: November 24, 2010
Location: Spring, TX
Posts: 1,552
|
http://www.burwellguns.com/misc/M&Ptriggerjob.pdf
This will probably help you out immensely. You owe me $10 |
November 27, 2012, 07:59 AM | #9 | |||
Senior Member
Join Date: February 15, 2011
Location: Gods waiting room.
Posts: 103
|
Quote:
So? Computers are plug~n~play, right? lol Moooo. Either way, no hard feelings, cupcake Quote:
Quote:
__________________
Glock 26 | Glock 36 | Glock 17L | Ruger LCP | Llama .38spc | NEF 10 gauge | NEF 20 gauge pump | Savage Mark II GL |Remington 770 | Remington 30/30 | Remington 25/35 | |
|||
November 27, 2012, 08:20 AM | #10 |
Senior Member
Join Date: June 24, 2012
Posts: 1,055
|
Federal Firearms License,Persons operating a gunsmith business have to be federally licensed,if you charge for services you're running a business.
|
November 27, 2012, 08:32 AM | #11 | |
Senior Member
Join Date: February 15, 2011
Location: Gods waiting room.
Posts: 103
|
Quote:
I will have to esquire as to whether or not this place has this Federal Firearms License thingie. Thanks man.
__________________
Glock 26 | Glock 36 | Glock 17L | Ruger LCP | Llama .38spc | NEF 10 gauge | NEF 20 gauge pump | Savage Mark II GL |Remington 770 | Remington 30/30 | Remington 25/35 | |
|
November 27, 2012, 10:24 AM | #12 | |
Senior Member
Join Date: October 19, 2008
Posts: 635
|
Quote:
|
|
November 27, 2012, 11:57 AM | #13 |
Senior Member
Join Date: July 15, 2006
Location: Fern Creek ,KY and Metro Louisville at large
Posts: 430
|
As mentioned a FFL is needed for gunsmithing.
If you are doing on your own , for pay as a means of livelihood then that is required. If your are doing it as a employee of the range , then they have the FFL.
__________________
Republic Arms and Armaments 07 1-502-231-1118 Machine Shop and Finishing Services to the trade and public |
November 27, 2012, 11:59 AM | #14 |
Senior Member
Join Date: June 14, 2004
Location: NY State
Posts: 6,575
|
In NY state ,if things are still the same , you would also have to have a NYS pistolsmithing license !!
__________________
And Watson , bring your revolver ! |
November 27, 2012, 12:00 PM | #15 |
Senior Member
Join Date: July 15, 2006
Location: Fern Creek ,KY and Metro Louisville at large
Posts: 430
|
A Apex kit is not really a "traditional" trigger job but a parts replacement.
But it is well within the scope of somebody who is not all thumbs. And I like cupcakes
__________________
Republic Arms and Armaments 07 1-502-231-1118 Machine Shop and Finishing Services to the trade and public |
November 27, 2012, 01:06 PM | #16 | |
Senior Member
Join Date: October 19, 2008
Posts: 635
|
Quote:
|
|
Thread Tools | Search this Thread |
|
|