Win 62A, Need Some Help

3StrikesNC · March 24, 2008, 07:03 PM

Posted elsewhere, trying to disassemble a Winchester 62A. Don't have a Manual, need one.

Stuck on removing the Foregrip as well as the Bolt.

Hawg · March 24, 2008, 07:24 PM

You have to remove the mag tube to remove the fore end. Can't help you with the bolt.

3StrikesNC · March 24, 2008, 07:26 PM

I took the pin out, but how do you get the tube out? Could it be rusted ?

Hawg · March 24, 2008, 08:08 PM

It's been a long time but if my memory is right it just slips in. Might be threaded but I really don't think so.

George R · March 25, 2008, 01:25 PM

HH is correct. It's just a slip fit. Maybe a little kroil or kerosene overnight will loosen it up. I can PM you an exploded view if that would help.

3StrikesNC · March 25, 2008, 05:08 PM

George; thanks, I have an exploded view from Steve's.

Am I correct, there is only one pin in the rear mag tube support?

3StrikesNC · March 25, 2008, 09:03 PM

I am redeemed!

Two days soaking in Liquid Wrench, an oak "drift" with a small hammer, and some courage supplied by TFL, .... and the mag tube came out without damage, the Foregrip is off, and the bolt is out.

Thanks. It is not threaded, just slips in.

Still looking for a Takedown Manual if anyone has one.

George R · March 26, 2008, 08:41 AM

I do have a receiver cross section that shows the relationship of the parts if you'd like that.

TEDDY · March 27, 2008, 08:15 PM

I just repaired one broken parts in carrier.every one should get the "GUN PARTS CAT"so many exploded parts prints.very useful.

-

---

March 24, 2008, 07:03 PM	#1
3StrikesNC Senior Member Join Date: October 22, 2007 Location: in a house Posts: 473	Win 62A, Need Some Help Posted elsewhere, trying to disassemble a Winchester 62A. Don't have a Manual, need one. Stuck on removing the Foregrip as well as the Bolt.

March 25, 2008, 01:25 PM	#5
George R Senior Member Join Date: December 17, 2004 Location: Boca Raton, FL Posts: 151	Win 62 HH is correct. It's just a slip fit. Maybe a little kroil or kerosene overnight will loosen it up. I can PM you an exploded view if that would help. __________________ http://www.gunblue.homestead.com

March 26, 2008, 08:41 AM	#8
George R Senior Member Join Date: December 17, 2004 Location: Boca Raton, FL Posts: 151	62A I do have a receiver cross section that shows the relationship of the parts if you'd like that. __________________ http://www.gunblue.homestead.com

March 27, 2008, 08:15 PM	#9
TEDDY Junior member Join Date: December 10, 2006 Location: MANNING SC Posts: 837	62a I just repaired one broken parts in carrier.every one should get the "GUN PARTS CAT"so many exploded parts prints.very useful.- ---

March 24, 2008, 07:24 PM	#2
Hawg Senior Member Join Date: September 8, 2007 Location: Mississippi Posts: 16,189	You have to remove the mag tube to remove the fore end. Can't help you with the bolt.

March 24, 2008, 07:26 PM	#3
3StrikesNC Senior Member Join Date: October 22, 2007 Location: in a house Posts: 473	I took the pin out, but how do you get the tube out? Could it be rusted ?

March 24, 2008, 08:08 PM	#4
Hawg Senior Member Join Date: September 8, 2007 Location: Mississippi Posts: 16,189	It's been a long time but if my memory is right it just slips in. Might be threaded but I really don't think so.

March 25, 2008, 05:08 PM	#6
3StrikesNC Senior Member Join Date: October 22, 2007 Location: in a house Posts: 473	George; thanks, I have an exploded view from Steve's. Am I correct, there is only one pin in the rear mag tube support?

March 25, 2008, 09:03 PM	#7
3StrikesNC Senior Member Join Date: October 22, 2007 Location: in a house Posts: 473	I am redeemed! Two days soaking in Liquid Wrench, an oak "drift" with a small hammer, and some courage supplied by TFL, .... and the mag tube came out without damage, the Foregrip is off, and the bolt is out. Thanks. It is not threaded, just slips in. Still looking for a Takedown Manual if anyone has one.