The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: General

Reply
 
Thread Tools Search this Thread
Old September 17, 2011, 07:01 AM   #651
Eghad
Senior Member
 
Join Date: May 28, 2005
Location: Texas
Posts: 6,231
Dayum...this thread still lives and more goodness from HUBEL!
__________________
Have a nice day at the range

NRA Life Member
Eghad is offline  
Old September 18, 2011, 01:56 AM   #652
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
Thankyou, Eghad. You have a neat handle.
But it isn't only me, much of it is the
work and help others have done also...Ed
__________________
ED HUBEL
HUBEL458 is offline  
Old September 22, 2011, 02:11 AM   #653
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
10ga FH ideas..Ok I think the most stylish guns in the world
are nicely built over/unders. And there is a heavy duty
10ga over under made by Armi San Marco, imported by
Cape Outfitters. That is one brand I've lately
seen some sold on GB. Others just as strong are Armsport
shown in the picture below, also
American Arms, and Richland Arms.
And probably a few more.

I'll be trying to get one I can afford, I could
ream one chamber for 4.05 brass case
for slugs, and leave other for 3.5" magnum shot and slug
loads in plastic cases. But if we left both 3.5" you'd
still have a hairy gun. You can buy 3.5" new plastic cases,
with hot Fed 239 primers for 22 cents each.
Make a real great combo gun.For slugs with
the right weight slugs.Don't go real heavy.

For slugs use the hollow base hard cast lead
900gr in brass case, at 1900 fps,that the
guy in AZ makes.In plastic about 1750.
Those are not a full bore loads,needing real thick
barrel, but that heavy O/U has barrels ok for that,
keeping pressures at mag shotshell levels.14,000 psi.

These modern O/U actions can take pressures like the
heavy duty NEF SB2 10-12ga frame, if barrels were thick
enough.20,000 in 10ga. IE the actions are real strong.
Ruger has made O/U rifles on their O/U frames,
and others have made big bore rifles
using modern over/unders. I like idea of O/U
double ten slug gun knowing the speed we have
gotten with our slow powder slug loads....Ed

__________________
ED HUBEL
HUBEL458 is offline  
Old September 28, 2011, 12:16 AM   #654
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
Some newer slug ideas coming around. First is Brenneke,
a locked on base ounce slug in sabot at factory speed of
16-1700 or so in 3" plastic.Really go in our 3.5" loads.

Second is Federal Deep Penetrator, 1 oz, copper plated
and a harder lead alloy, than Federals regular slugs.

Third is Dupleks, steel slug riding on a plastic band,
penetrates very well. About 1 1/8 oz.

Seeing the slug base attached deal from Brenneke,
in a sabot I figured out the following.
The idea is the new BPI blue sabot, being undersize for
12ga, is a perfect fit in a 10ga bpi wadcup, The blue has no
cushion on it so it sits in cup ok and a roll crimp works.
Just shaved bottom edge corner and fits bottom ok.
In 32" heavy barrel NEF 10ga, and 10ga 3.5" plastic case,
gets over 2300 at less than mag shotgun pressures
with 440gr slug in blue sabot.I plan on in future to
make a 10ga with rifled barrel, which these would be best in.

If I can find thin wall 10ga wadcup the 12ga bpi AQ slug
would work even better, as it is for smooth bores....Ed




__________________
ED HUBEL

Last edited by HUBEL458; September 28, 2011 at 11:35 PM.
HUBEL458 is offline  
Old October 6, 2011, 11:52 PM   #655
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
Here are pictures of the full bore Lee Key Slug
I had a guy cast. He took Lee Key mold and machined
it out to cast a .729" full bore slug. In picture
is a regular soft lead Foster style to compare with.
Slugs are hard alloy and can be speeded up ok.
In 2nd picture is two MRC 2 5/8" brass cases with
slugs in them. These slugs with those brasscases are
being tested first in rifled barrels in a guys 1887 WIN.
The slugs have real good shoulder to
roll crimp against when used in plastic cases.
These first ones are 500 gr. We are going to
work on another die to get the weight about 600gr,
that the brass case guys want to use.
Lee molds are not real high price so it isn't
a bad deal to get them and machine them.Ed.



__________________
ED HUBEL
HUBEL458 is offline  
Old October 16, 2011, 11:14 PM   #656
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
The first full bore Lee Key slugs were 490 gr,
that we had made. Good for 2300 in 3.5" plastic
and 27-2800 in 3.5" RMC brass cases in the
long barrel NEF.

For the 8ga Hubel Falling Block pictured
above; For now using 3.3" swaged kiln cases. We swage
them to fit the 8ga chamber in falling block.
The barrel is real thick so we can run 50-60,000 psi
if we want in that action. The heavy duty 8ga plastic will
take about 23000 psi. A MRC turned brass would do
35,000 psi. But the plastic does so great,for now I'm
staying with 70 cent 3.3" plastic, primed with 239 primers,
good for 4 shots or more.

And I have the REM wadcup, on left in picture, with
its own seal, that they use for the kiln slug, which works
for various other slugs and shot loads.

In the 8ga HFB - 3.3" plastic cases-
1020gr 2000 -- 900gr to 2200 ---- 770gr to 2400---
and triple ought buckshot load---
9 - 70 gr 000 buckshot, in wadcup. 630 gr total-- 2600.Ed

__________________
ED HUBEL
HUBEL458 is offline  
Old October 29, 2011, 02:46 AM   #657
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
Remember these from above-Well 2nd picture is penetration tests with
them. Over 2000 for 320 gr weight in plastic cases..
3rd picture is an all aluminum version without brass center
from penetration tests. 198gr at about 2500 in plastic cases.
Now the locked on bases are not burnt and the reason I understand
is they use a thin card between seal and powder, up inside the
seal cup.This info and testing by US-S group in the EU.
The plastic cup seal out there might benefit from that, like
card disc inside the cup of the BPGS and similiar seals.Ed




__________________
ED HUBEL
HUBEL458 is offline  
Old October 29, 2011, 09:52 AM   #658
Eghad
Senior Member
 
Join Date: May 28, 2005
Location: Texas
Posts: 6,231
Quote:
Thankyou, Eghad. You have a neat handle.
But it isn't only me, much of it is the
work and help others have done also...Ed

thanks to the team.....

No you just need to come up with a team name

Team: Hell Rifle ?
__________________
Have a nice day at the range

NRA Life Member
Eghad is offline  
Old November 3, 2011, 11:42 PM   #659
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
In the early days; in my Greener's book he states that rifled,
choke bored 12ga paradox shotguns with slugs, heavier powder
charges than shot loads, could hold what amounted to
about 5 inch pattern at 100 yds.

And still had 1800 ft lbs energy at 100yds.
And that is with guns with lighter, weaker barrels
than we have today, so our work in a good extension
of what the early big bore guys did.

And then the 4bore for guys liking a big challenge, 3rd picture...Ed





__________________
ED HUBEL
HUBEL458 is offline  
Old November 5, 2011, 12:49 AM   #660
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
Thanks to rattler on 24hr for the old time pictures,
and the guys really like them.
Some info about the early days of slug guns;
In my Greener's book he states that rifled,
choke bored 12ga paradox shotguns with slugs, heavier powder
charges than shot loads, could hold what amounted to
about 5 inch pattern at 100 yds.

And still had 1800 ft lbs energy at 100yds.
And that is with guns with lighter, weaker barrels
than we have today, so our work is a good extension
of what the early big bore guys did.

Many have success with all kinds of high-power slug designs and
with extra power, have pushed the reliable range of 12ga slugs/bullets
from 75 yds to over a 150 yds. Here is picture from a 1926
Manton catalog showing many brass case old slug loads.
Notice the 20bore/gauge one, seems as hotrod 20s are old hat....
Both Pictures from lancaster and CptCurl on Nitroexpress.

2nd picture are saboted slugs, called the SAGA, from Spain,
next to a Brenekke on the right..AS far as I can find only
sold as loaded rounds. They look great to reload with.Ed



__________________
ED HUBEL

Last edited by HUBEL458; November 5, 2011 at 12:07 PM.
HUBEL458 is offline  
Old November 8, 2011, 05:18 AM   #661
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
Here is a picture of 8bore elephant guns from
my Greener book.ED

__________________
ED HUBEL
HUBEL458 is offline  
Old November 9, 2011, 10:10 AM   #662
Budda
Senior Member
 
Join Date: November 7, 2011
Location: Earth
Posts: 446
Any video of that CANNON going off? that would put you ass in the dirt for sure!
Budda is offline  
Old November 13, 2011, 08:47 PM   #663
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
You can see videos of various 4bores, etc on Youtube.Ed
__________________
ED HUBEL
HUBEL458 is offline  
Old November 19, 2011, 08:51 PM   #664
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
Here is picture of an early falling block for big bores
called the Field I think. Looks like some other
side levers, looks like lever works forward.

And speaking of falling blocks next picture is the
start or 'fixins' so to speak for the next step
up, for my 2bore. Same design as the 4 and 8
bores only wider.

I am now getting 2.25" OD barrel reamed
out to the two bore size.
And a square hole for breach block done
in that hunk of 4130 steel.

Other experimenting, a while back, when I made
my 585 Short HE from Gibbs cases, I also made a
620 Short HE from Nyati case, of the same design,
IE, head spacing on the mouth and extractor.
Using 600NE .620" diameter bullet and 2.7" long case.
Case could be shorter or longer like the 585 one.
Didn't do much with it as its sides were very straight
only .010" taper of both sides together. Whereas the
585 Short HE had .027" total taper both sides. And any
Nyati brass I got, went to make my 585HE cases..Ed





__________________
ED HUBEL
HUBEL458 is offline  
Old November 29, 2011, 12:26 AM   #665
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
First is picture sectioned Explora case and slug, showing how
they kept weight down so that it could be stepped up in
speed in older doubles, with just short rifling section at muzzle,
that didn't have real heavy barrels. Second picture from Greener
book here, is of older 4 and 8 gauges.

Third picture shows steps of making 4bore case, one inch bore,
from 20mm. 2nd in picture is case with base turned and swaged
to size which leaves base smaller than rim, for rimmed case.
Then 3rd case has top expanded to take 1" diameter slug.
last shows the thickness and strength of finished case.

Testing factory 20ga Hastings sabot slug 3.5" hotrod loads, and
reloaded with 20ga SPW identical slugs, 390gr, goes about 2200
from 30" heavy barrel. Load was 75gr of 4759.
Factory is about 1900. For regular modern barrels you could
do with 65 gr and get about 2000.Ed





__________________
ED HUBEL
HUBEL458 is offline  
Old December 3, 2011, 09:21 PM   #666
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
Some info about our slower powder reloads in plastic and
brass cases with shotgun primers for modern 12ga guns.
I now prefer the IMR 4759 over 4227 as we have had
some delayed firing problems when the loaded cases get
real cold with 4227..And with slower powder loads use
magnum primers.

A side note,in same vein, you know I now use FED239
mag primers in my 8ga and 4ga, but we find they they really
solve the real cold gun, ignition problems, in muzzle loaders
using black powder substitutes, with shotgun primer
inline guns. We tested 50cal and a primer sold especially
for ML when fired,no powder, only saw a tip of the flame
out the barrel, a FED209 mag about 4" flame, buta Fed 239
Mag primer about a foot of flame.

Some more info from the old days, here is picture of
a variety of slugs being promoted and used a century ago.
And 2nd picture Paradox cases old and new.Bottom one is a
modern version sold by H&H for slug hunters.Ed



__________________
ED HUBEL
HUBEL458 is offline  
Old December 3, 2011, 10:37 PM   #667
checkmyswag
Senior Member
 
Join Date: January 29, 2011
Location: Texas
Posts: 1,328
Had to post just to change the thread due to attached image!

Interesting stuff about the shotgun ammo too.
Attached Images
File Type: png 2011-12-03_2135.png (9.7 KB, 43 views)
checkmyswag is offline  
Old December 14, 2011, 03:03 AM   #668
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
We are always looking for way to shoot 8 and 10s
using easy to get components,cheap, without buying
loaded rounds for big bucks, if available at all.

In 8ga falling block, plastic got 930gr hollowbase
slug to 2300, It is a slug for 10 ga that we expanded
base a little to fit tight in 8ga wadcup. On the left in
picture. At 30 yds 3" group. Just with open sight,
About like the 10ga sight bead. There is enough hollow in
the base it flies pretty good from 8ga smooth barrel.

Along same line, in my 10ga 32" smooth bull barrel with a
750 gr .69cal hollowbase Dixie MZ slug in VP100
10ga wadcup about same speed and same accuracy.
Nice to just get a box of slugs that is in stock,
and a 2cent cent wadcup and Fed 3.5" 10ga plastic cases
and be shooting cheap.And the cases roll crimp nice
down to these slugs.

And also the hotrod 20 ga 3.5" Hastings factory loads in
a smooth barrel moderate weight 20ga shoots about
same accuracy even though they say for rifled, but that
SPW slug/wad combo has enough plastic and seal on the back
and to shoot like aBrenekke. The new 28ga Brenekkes
out of 28ga NEF modified choke barrel shoots same at 30yds.
Scoped guns and good eyes would shrink groups.Ed

__________________
ED HUBEL
HUBEL458 is offline  
Old December 21, 2011, 01:34 AM   #669
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
A different, interesting style, of 12ga slug, from Russia.
First picture loaded round, in plastic, roll crimped.
Second, two types of slugs they have on the same base.
Base for rifled barrel, little smaller diameter than the front.
Looks like the roll crimp locks against
the edge of the base. Neat idea, and it could have a
flat meplat slug on the front of the base like
the US-S brass slugs fron Greece are on the
plastic bases that I have here. They must use a crimping
die with a deep hollow up in the middle. We have thought
of taking a roll crimper and putting a deeper recess
in middle to load longer nose slugs further out so as to
have more room for our slower powders.ED



__________________
ED HUBEL
HUBEL458 is offline  
Old December 28, 2011, 12:38 PM   #670
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
Here is picture of 4 long cases of
RIP's on the AR forum.
Top being a Rocky Mtn Cartridge
3.5" turned brass 20ga. In 20ga
getting these and lengthening chambers
allows use of the 3.5" 20ga plastic also.
Some factory guns are 3.5"

Next a RMC 3.5" turned brass 12ga.
Chambered for these you can use
3.5" 12ga plastic also.Some guns are
3.5" from the factory.

3rd down our 3.85" 12ga FH we made from BMG brass.
Bottom a RMC 3.85" turned brass 12ga FH case.




Next picture shows one of the old ways they locked slugs
into paper cases. Many old slugs had a wide deep groove
which made it possible to crimp that way.You can
see one of those slugs in the picture.




Testing 490gr 12ga full bore Lee style slugs in 3.5"
plastic at 2200. Works in the long barrel rifled NEF and
the Khan 12ga 3.5" auto smooth bore.

In same guns the 570gr US-S brass slug with
locked on base at 1900 in 3.5" plastic worked also.
It is great to see a smooth bore slug like the US-S
that is as accurate as most fullbore slugs from
rifled barrels.Maybe they will be imported soon
from European Cartridge.Ed
__________________
ED HUBEL
HUBEL458 is offline  
Old January 5, 2012, 03:23 AM   #671
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
Here are couple more pictures of longer bullets
in sabots, loaded in plastic cases, with the
roll crimp down against the sabot. Both are
ideas tested by European Cartridge in Greece,
who make the US-S slugs. Both longer bullets
pictured have the locked on base that their
other US-S slugs have, for smooth bore accuracy.
2nd picture shows a deep hollow roll crimper
for doing slugs like these.Ed



__________________
ED HUBEL
HUBEL458 is offline  
Old January 10, 2012, 07:36 PM   #672
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
This picture of an RC4 brand slug I see is available
down under. It has locked base like Brenekke.
And locked on without discarding petals, like US-S.

And 2nd picture is a group fired with RC4 slugs
by fellow on NitroExpress forums from
double 12ga, 2 left and 2 rights at 25yds.

3rd picture is a discarding sabot base, and with
four discarding sabot carriers, with centered
penetrating solid bullet, from France.







__________________
ED HUBEL
HUBEL458 is offline  
Old January 17, 2012, 11:39 PM   #673
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
Some more slug and sabot ideas folks are doing.

First is a long pointed slug with locked on base,
It goes to target with base,can work smoothbore.



Second is picture of Hexolit sabot base slug
with petals expanded, sure would make bad wound.



Third shows a variety of Gualandi slugs you can
get for reloading, and we're finding that these
locked base slugs, Brenekke/USS style slugs, are
giving good accuracy in smooth barrels which can
save when doing heavy barrels.Weights shown in
grams, get our weights in grains multiply by 15.4..Ed

__________________
ED HUBEL
HUBEL458 is offline  
Old January 19, 2012, 11:22 PM   #674
HUBEL458
Senior Member
 
Join Date: March 8, 2000
Posts: 751
Here are some more sabot/slug and loading concepts.

First is Alcan 2.75" paper case with Dixie 600gr slug,
with the side of the case crimped into the relief/lube
groove of the Dixie slug.The groove in the Dixie isn't
quite as deep as the groove in the Fosbury slug shown
in earlier post, but still seems to crimp fairly tight.



Next are various slugs in 12ga REM sabots that take
57 cal slugs and bullets.Those sabots are from the REM
Accutip loadings. In picture you can see one of the
REM 385gr jkt bullets they use. Also is sabot
with 20ga cast Lyman. On right sabot with hardcast 585 cal
640gr lead bullet, the ones I use in my 585HE wildcat
case. I sized it down a little, perfect fit.
Also the .575 cal Dixie Gunworks lead slugs will do.

Also shown is a long pointed 55 Boys bullet in one,
fairly tight fit.We cut back .3" of bullet off so it
fit for length in sabot and is 750gr.



Third are 3.5" brass and plastic with the REM sabot and
the 750gr pointed slugs in them.In all the sabot work we
and others have done, trying to get accuracy and high
speeds together, maybe there is such a thing as too
much plastic. IE, sabots too thick on the sides if doing
50cal or smaller in 12ga sabots, for heavier slugs
at high speeds. Thinner sides may discard more evenly at
the greater pressures and violence of high speeds.
Thin sides may have less give so that sabot grips slug
better to impart spin in rifled use. Example in
smoothbore use is the USS slugs, where the brass slug
is .629" with thin discarding petals that have proven to
be very accurate. And with both reasonable priced sabot
offerings the last few years being undersize, accuracy
problems, etc, maybe time to try something else.

Got to find whole bunch of these sabots. Are these pictured
12ga REMs the only 58cal ones around? I can't find others,
and maybe we can find where these are made. As I have
huge numbers of the 585 slugs, which by the way I think
is best hunting combination, without extremely heavy slugs
which suffer for the speeds needed for longer range use.
It is hard lead, good for big game.And my guy can make many,
many more if needed whether for 585HE rifles
or in sabots if we can find some.ED

__________________
ED HUBEL
HUBEL458 is offline  
Old January 20, 2012, 04:16 AM   #675
FrankenMauser
Senior Member
 
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,390
Some of these slugs are just wicked.
Thanks for the update, Hubel.
__________________
Don't even try it. It's even worse than the internet would lead you to believe.
FrankenMauser is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:08 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.15592 seconds with 9 queries