April 30, 2011, 01:36 AM | #26 |
Senior Member
Join Date: January 5, 2009
Location: Just off Route 66
Posts: 5,067
|
i hate trimming brass
Welcome to the Club.
Jim
__________________
Si vis pacem, para bellum |
April 30, 2011, 02:01 AM | #27 | |
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,426
|
Quote:
My gunsmith is the same way. He is a machinist by trade, makes his "bread money" off his day job, makes the "good" money off custom machining, and is just a gunsmith on the side (turned a hobby into a slightly profitable venture). He sells a few "machinist's" tools (primarily assembly jigs, from what I understand) for extra cash, but he never created them with the intent to make money. He made them for himself first, and decided to make the product available to others some time later.
__________________
Don't even try it. It's even worse than the internet would lead you to believe. |
|
April 30, 2011, 06:31 AM | #28 |
Member
Join Date: April 27, 2011
Location: Joplin MO
Posts: 33
|
Has anyone used the RCBS x-dies and do they really work the way the manufacturer advertises?
|
April 30, 2011, 07:05 AM | #29 |
Senior Member
Join Date: August 3, 1999
Location: Houston, Texas
Posts: 2,991
|
I just gutted it up and bought an RCBS power trimmer with the 3 way cutters. It is expensive but works great. No regrets.
__________________
10mm and 357sig, the best things to come along since the 38 super! |
September 8, 2012, 09:29 AM | #30 |
Senior Member
Join Date: January 10, 2012
Posts: 3,881
|
I have the Lee case trimmer that I chuck in a cordless drill, but the cases keep coming loose no matter how much I tighten them. What could be wrong or what am I doing wrong ?
|
September 8, 2012, 10:14 AM | #31 |
Senior Member
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,930
|
Rebs there is nothing wrong with trimmer. I would lay a hefty wager on bent, and/or thin weak rims. For .223 Rem I have found AR fired Remington brass to be the worst about doing this. In fact if I see a head stamp of R-P on .223 I scrap it for just such reason. Some others will do this as well I just scrap them due to the fact that I have so much .223 brass anyway.
If your cordless drill has a setting for lower speed try it on the lower speed it helps to prevent some of the wobble effect from badly bent rims.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you. |
September 8, 2012, 11:40 AM | #32 |
Senior Member
Join Date: January 15, 2012
Location: Western New York
Posts: 466
|
I don't know anyone who enjoys trimming brass
__________________
Lock and load, the zombies (democrats) are coming (to take your guns)! |
September 8, 2012, 11:46 AM | #33 |
Senior Member
Join Date: March 21, 2012
Location: Connecticut
Posts: 2,378
|
Lee case trimmer, would be nice if they beefed up the shell holder, or just put a handle on the lock ring.
|
September 8, 2012, 12:40 PM | #34 |
Senior Member
Join Date: December 4, 1999
Location: WA, the ever blue state
Posts: 4,678
|
When I started handloading I got an RCBS rockchucker press kit that came with an RCBS case trimmer.
I was resizing .223 and 308 by having the die touch the shell holder [ lots of should push back, for those in Rio Linda]. That is enough to make anyone quit reloading, let alone trimming. ------------------ Then I put an RCBS Pro 3-way cutter in a vertical mill and a Lee Lock stud in the mill vise, pair of long nosed vise grips were used to turn the Lee shell holder like a handle. I could trim, inside chamfer, and outside chamfer in 5 to 10 seconds per round. ------------------------------- I now collet neck size where possible, and if I have to push a shoulder back, I do the absolute minimum I can get away with. The higher the pressure, the more a case shrinks when fired, and them more it grows when the shoulder is pushed back by a full length sizer die. I have fired 223 at 66kpsi for 20 times without trimming. ------------------ Then there is always being lazy and just buying new brass, but you may still have to chamfer the inside of the neck.
__________________
The word 'forum" does not mean "not criticizing books." "Ad hominem fallacy" is not the same as point by point criticism of books. If you bought the book, and believe it all, it may FEEL like an ad hominem attack, but you might strive to accept other points of view may exist. Are we a nation of competing ideas, or a nation of forced conformity of thought? |
September 8, 2012, 12:42 PM | #35 |
Senior Member
Join Date: February 5, 2012
Location: Southwest WA Coast
Posts: 559
|
For most hand crank trimmers you can simply remove the shaft, grind off the handle and turn down the end of the shaft to a quarter inch. Replace the shaft and attach any variable speed drill motor and you have an inexpensive conversion to a power trimmer. Remember to lube as it runs a lot faster.
|
September 8, 2012, 03:36 PM | #36 |
Senior Member
Join Date: July 18, 2008
Posts: 7,249
|
My favorite method, the forming/trim die, something like sizing a case except the reloader uses one of the ‘man’ tools, the file, I have the electric case trimmer for 223, not a problem but the design trims from the shoulder, if case length is important the reloader must learn to add A + B to get C or adjust the die (Dillon) to compensate for the length of the case from the head of the case to its shoulder, OR do as everyone else and disregard A and full length size all of the cases to minimum length.
F. Guffey |
September 8, 2012, 05:50 PM | #37 |
Senior Member
Join Date: October 18, 2006
Posts: 7,097
|
A Possum Hollow trimmer chucked into a hand drill saved my sanity when processing 2k of 223 brass.
Jimro
__________________
Machine guns are awesome until you have to carry one. |
September 8, 2012, 06:21 PM | #38 | |
Senior Member
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,720
|
Quote:
The WFT trimmer also looks interesting. http://www.littlecrowgunworks.com/wft.html
__________________
"Everything they do is so dramatic and flamboyant. It just makes me want to set myself on fire!" —Lucille Bluth |
|
September 8, 2012, 09:31 PM | #39 |
Senior Member
Join Date: January 6, 2011
Location: Thornton, Texas
Posts: 3,998
|
I use that RCBS trimmer with the 3 way cutter. It's pretty fast, at maybe 6 or 8 seconds to the case, or maybe less. The big reason I'm a fan of that setup is that I can do all 3 trim functions to the same degree in one pass. Even with that, the thought of doing 2000 cases makes me cringe. A big day for me might be 300 cases.
|
September 9, 2012, 03:19 AM | #40 |
Senior Member
Join Date: March 21, 2012
Location: Connecticut
Posts: 2,378
|
I like the lee over the wft, only handle the case once and I can trim it, chamfer inside and out, polish and brush the inside of the neck. I think if you drill and tap the lock ring and thread some small handle on it, it would be just about perfect.
|
September 9, 2012, 08:09 AM | #41 | ||
Senior Member
Join Date: July 8, 2012
Location: so cal
Posts: 246
|
Quote:
Quote:
cases still need chamfer (it does a passable job deburring). |
||
September 9, 2012, 08:52 AM | #42 |
Senior Member
Join Date: June 2, 2011
Posts: 177
|
|
September 9, 2012, 08:38 PM | #43 | |
Senior Member
Join Date: May 25, 1999
Location: Too close to Houston
Posts: 4,196
|
Quote:
Just trim the cases you want to load today. The rest can wait until you want to load them. Have you already sized all of the cases?
__________________
Proud member of the NRA and Texas State Rifle Association. Registered and active voter. |
|
September 9, 2012, 08:41 PM | #44 |
Senior Member
Join Date: December 19, 2008
Location: milton, wv
Posts: 3,640
|
do like at least one of the members here does...
.. send them to someone else and have them trim em for ya.. . does cost a bit.. but saves you the hassle.
__________________
Desert Eagle Alliance Group Launcher Extraordinaire ______ ----Get Busy Live'n.....Or....Get Busy Die'n......Red -------They call me Dr. Bob,,,, I have a PhD in S&W |
|
|