The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools Search this Thread
Old October 19, 2012, 09:24 PM   #1
joneb
Senior Member
 
Join Date: December 10, 2005
Location: Central , OR
Posts: 1,888
Colt Trooper 357 magnum

I was tempted by one today with a 4" barrel. The seller wanted $429, I offered $275 because there was major bluing issues, I would rate its condition at 80-85%.
It did appear to have the original grips that appeared to be in good condition with silver Colt medallions.
The lock up was tight, further inspection didn't happen as the seller would not go below $350. So I walked
Should I go back with a offer of $300 or just forget about it ?

Thanks jj
joneb is offline  
Old October 19, 2012, 11:51 PM   #2
22-rimfire
Senior Member
 
Join Date: February 19, 2005
Location: Tennessee
Posts: 5,323
I think I answered your question over at that other place.

You are talking about a Trooper manufactured after 1962 in 357 caliber (Blue Book says 1961 when the 3-5-7 Mag model was discontinued) and prior to the introduction of the Trooper Mark III. I would offer $400 if it is an original Trooper. I passed on one that was as new in 357 magnum that the seller was asking a firm $650 with pachmayr stocks. I offered $500 on that one.

Last edited by 22-rimfire; October 20, 2012 at 12:06 AM.
22-rimfire is offline  
Old October 20, 2012, 12:38 AM   #3
joneb
Senior Member
 
Join Date: December 10, 2005
Location: Central , OR
Posts: 1,888
With all do respect 22-rimfire demographics play a big part in the value of such things. The seller could put this item on Gun Broker but that would add additional costs, perhaps 50-75 dollars for shipping and transfer fees.
joneb is offline  
Old October 20, 2012, 12:41 AM   #4
joneb
Senior Member
 
Join Date: December 10, 2005
Location: Central , OR
Posts: 1,888
To add clarity to this thread;
http://www.thehighroad.org/showthread.php?t=681879
joneb is offline  
Old October 20, 2012, 12:42 AM   #5
22-rimfire
Senior Member
 
Join Date: February 19, 2005
Location: Tennessee
Posts: 5,323
You're right. My $400 may be a tad high since they were asking $429. Prices do vary from area to area. I would have taken the $350 and smiled if I wanted a shooter. The reason I did not buy the other Trooper mentioned was the lack of original stocks. They would have cost me $150-$200 to replace plus my time and effort. No box either.

Added: I am generally not interested in shooters anymore. I have that covered. I ALMOST bought that other Trooper. I was within a breath of saying ring it up. This was earlier this year. I still think about that one as I really do like the original Troopers. In the case of your revolver, I would only buy for resale and $400 is too high for that.

Last edited by 22-rimfire; October 20, 2012 at 12:49 AM.
22-rimfire is offline  
Old October 20, 2012, 02:02 AM   #6
DPris
Member Emeritus
 
Join Date: August 19, 2004
Posts: 7,133
Jibjab has correctly identified the model he's refering to.
In that condition I'd go $350, IF I wanted one bad enough.

And as mentioned on the other forum just be aware that there are limited service options for those older Colt actions if needed.
Denis
DPris is offline  
Old October 20, 2012, 08:01 PM   #7
Winchester_73
Senior Member
 
Join Date: December 20, 2008
Location: Pittsburgh PA
Posts: 2,863
Always offer the $300. Maybe he will take it, maybe he will say $350, which you already know. Very few of the Colt DA guns, esp in cals bigger than 38 special can be found for this kind of money. Look around - they are in demand.

I'm not sure why this same question was posted more than once on various threads. These troopers are not often seen in my neck of the woods, and for $350, with original finish and stocks, its a buy. Be sure to check it for lock up with the hammer back on each chamber AND then AGAIN with the trigger held back but the hammer down. If you are able to move the cylinder out of lockup at any point, the gun needs re-timed by Colt. Call them and make sure they will do the work. Many of the old models they don't work on anymore.
__________________
Winchester 73, the TFL user that won the west
Winchester_73 is offline  
Old October 20, 2012, 09:32 PM   #8
joneb
Senior Member
 
Join Date: December 10, 2005
Location: Central , OR
Posts: 1,888
Thanks for the advise.
Quote:
Be sure to check it for lock up with the hammer back on each chamber AND then AGAIN with the trigger held back but the hammer down. If you are able to move the cylinder out of lockup at any point,
With the hammer cocked there was rotational movement and end play in all six positions. With the hammer down and the trigger held lock up was tight in all six positions.
joneb is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:33 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.04989 seconds with 10 queries