super black hawk

rustyshoe · January 23, 2013, 06:22 PM

The pin that holds the cylinder in place, backs out after a couple of rounds, took it to a smith, no better, whats next ??

Tatume · January 23, 2013, 06:55 PM

Install a Belt Mountain locking base pin. They are available from Brownells, among other places. It is a drop in replacement with one exception. You must remove the locking set screw, and using a drill press and a jig (you can make your own from wood and clamps) drill a shallow depression in the underside of the barrel. That will give the set screw a place to go. It is really very easy. Don't drill deep, just a tiny depression.

FrankenMauser · January 23, 2013, 10:32 PM

Tell the 'smith you want your money back, or have them send it to Ruger.

ChiefTJS · January 23, 2013, 11:00 PM

You can also install a heavier latch spring.

oldgunsmith · January 24, 2013, 12:17 AM

I've always kept an eye on the bearing surface around the underside of the screw head. The older & blinder you get the more magnification helps. It usually gets to looking pretty beat up visibly before it starts letting the base pin get by. I have several old models and always keep a couple of spare latch ass'ys around. Being sure to keep it tight helps. When the notch (or groove) on the base pin starts looking beat up it gets replaced as well. The 41's & .44's seem to be the worst offenders, but .357 can do it, too.

Pathfinder45 · January 24, 2013, 01:37 AM

My .45 Colt Vaquero did the same thing when it was new. I took the cylinder pin out and used a small chainsaw file to file the locking groove just a little deeper. End of problem. Many thousands of rounds later it has never recurred.

GeauxTide · January 24, 2013, 09:02 PM

I have Belt Mountain Base pins in my six Blackhawks. They are cheap and they work.

Northrider · January 24, 2013, 10:33 PM

I had the same issue with mine. Tried replacing the pin and spring both but it still kept coming out. Ended up sending it to Ruger. Three weeks later it was back, perfect. Works like a charm. No charge at all.

481 · January 24, 2013, 11:34 PM

One of the two SBHs I have was also like that. Ruger took good care of me and I got the gun back about a month and a half later. No problems as of six years later.

January 23, 2013, 06:22 PM	#1
rustyshoe Junior Member Join Date: January 19, 2013 Posts: 5	super black hawk The pin that holds the cylinder in place, backs out after a couple of rounds, took it to a smith, no better, whats next ??

January 23, 2013, 10:32 PM	#3
FrankenMauser Senior Member Join Date: August 25, 2008 Location: In the valley above the plain Posts: 13,424	Tell the 'smith you want your money back, or have them send it to Ruger. __________________ Don't even try it. It's even worse than the internet would lead you to believe.

January 24, 2013, 01:37 AM	#6
Pathfinder45 Senior Member Join Date: January 7, 2008 Posts: 3,224	No Big Deal........ My .45 Colt Vaquero did the same thing when it was new. I took the cylinder pin out and used a small chainsaw file to file the locking groove just a little deeper. End of problem. Many thousands of rounds later it has never recurred.

January 24, 2013, 11:34 PM	#9
481 Senior Member Join Date: April 18, 2011 Posts: 540	One of the two SBHs I have was also like that. Ruger took good care of me and I got the gun back about a month and a half later. No problems as of six years later. __________________ QUANTITATIVE AMMUNITION SELECTION

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

January 23, 2013, 06:55 PM	#2
Tatume Junior Member Join Date: January 20, 2013 Location: Gloucester, Va. Posts: 9	Install a Belt Mountain locking base pin. They are available from Brownells, among other places. It is a drop in replacement with one exception. You must remove the locking set screw, and using a drill press and a jig (you can make your own from wood and clamps) drill a shallow depression in the underside of the barrel. That will give the set screw a place to go. It is really very easy. Don't drill deep, just a tiny depression.

January 23, 2013, 11:00 PM	#4
ChiefTJS Member Join Date: June 25, 2009 Location: Omaha, Nebraska Posts: 96	You can also install a heavier latch spring.

January 24, 2013, 12:17 AM	#5
oldgunsmith Senior Member Join Date: January 9, 2013 Posts: 278	I've always kept an eye on the bearing surface around the underside of the screw head. The older & blinder you get the more magnification helps. It usually gets to looking pretty beat up visibly before it starts letting the base pin get by. I have several old models and always keep a couple of spare latch ass'ys around. Being sure to keep it tight helps. When the notch (or groove) on the base pin starts looking beat up it gets replaced as well. The 41's & .44's seem to be the worst offenders, but .357 can do it, too.

January 24, 2013, 09:02 PM	#7
GeauxTide Senior Member Join Date: April 20, 2009 Location: Helena, AL Posts: 4,423	I have Belt Mountain Base pins in my six Blackhawks. They are cheap and they work.

January 24, 2013, 10:33 PM	#8
Northrider Senior Member Join Date: February 22, 2011 Location: Wasilla, Alaska Posts: 228	I had the same issue with mine. Tried replacing the pin and spring both but it still kept coming out. Ended up sending it to Ruger. Three weeks later it was back, perfect. Works like a charm. No charge at all.