|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
February 8, 2015, 08:19 PM | #1 |
Senior Member
Join Date: December 6, 2013
Posts: 246
|
bullet seat and crimp verses factory crimp die
I know this has probably been around the forum allot.
I was about to invest in 9mm and 38 special factory crimp dies for my lee breech lock single stage. i hear some people say it's a must have and others not so. i personally haven't had too much trouble adjusting the combo bullet seat die, but wondering if overall my ammo will be of a better quality, more uniform and run better ? i may end up getting a turret press this year so not too worried about adding an extra step. thanks.
__________________
"If you think it's expensive to hire a professional to do the job, wait until you hire an amateur." Red Adair |
February 8, 2015, 08:32 PM | #2 |
Senior Member
Join Date: February 15, 2009
Posts: 8,927
|
I and others don't use FCD's on those cartridges and have no problems. Therefore, they're not mandatory. Factory commercial ammo is made without them, too.
|
February 8, 2015, 09:00 PM | #3 |
Senior Member
Join Date: December 23, 2005
Location: Minnesota
Posts: 2,955
|
I use the Lee Factory Crimp die for all my handgun ammo. When set up properly and used correctly it is no better or no worse than any other stand alone crimp die. Unlike other stand alone crimp dies it has a carbide sizing ring at the base. This ring will ensure that all your handloads will fit-n-feed.
Great tool and an excellent addition to any reloading bench. As this thread grows you will find that the LFCD is either loved or hated. You will also find that most of those that "hate" this wonderful tool have never tried it. Go figure. Last edited by steve4102; February 8, 2015 at 09:24 PM. |
February 8, 2015, 10:28 PM | #4 |
Senior Member
Join Date: December 6, 2013
Posts: 246
|
after thinking about how the combination bullet seat die works, if you have anything other than a very light crimp, i would imagine the crimp stage to possibly dig in to the bullet as it's being seated as the two events are happing simultaniously. could cause minor deformation of the bullet ?
__________________
"If you think it's expensive to hire a professional to do the job, wait until you hire an amateur." Red Adair |
February 9, 2015, 12:17 PM | #5 |
Senior Member
Join Date: February 15, 2009
Posts: 8,927
|
You're right.
The accuracy of handgun ammo isn't precise enough to reveal the crimp's effect of unbalancing the bullets. Sometimes a heavy crimp produces more uniform pressure curves with real slow handgun powders. As crimp's add another variable to ammo performance, the least amount to meet your objectives is best. Some 38 Spcl +P jacketed ammo has heavy crimps on heavy bullets. Wadcutter, mild match ammo has minimal crimp. Last edited by Bart B.; February 9, 2015 at 12:29 PM. |
February 9, 2015, 01:21 PM | #6 | |
Senior Member
Join Date: February 7, 2009
Location: Southern Oregon!
Posts: 2,891
|
Quote:
Now this is my experience with Lee FCD; If your dies are properly adjusted, then there is no need for a post seating/crimping sizing of the cartridge. I have never had a cartridge that would not chamber that re-sizing would fix, cover up mebbe, but not fix. My whole problem is new reloaders are told to use an FCD, rather than told how to properly adjust their dies. Case bulge? Just re-size it, iron out the problem rather than solve and fix...
__________________
My Anchor is holding fast! I've learned how to stand on my own two knees... |
|
February 9, 2015, 01:24 PM | #7 |
Senior Member
Join Date: January 5, 2009
Location: Just off Route 66
Posts: 5,067
|
For handgun ammo a separate crimp die is not necessary, even revolver ammo can be crimped with the seating die for a roll crimp.
HOWEVER, (there is always a however), I always use the FCD not so much for a crimp, but to insure the mouth flare from the powder through die has been remove so all cases will feed without hanging up on the chamber of the handgun and avoid ANY feed issues from the magazine. For me that is the "Priceless" part of using the extra die. Stay safe and shoot straight. Jim
__________________
Si vis pacem, para bellum |
February 10, 2015, 01:21 AM | #8 |
Senior Member
Join Date: January 24, 2009
Location: Anchorage Alaska
Posts: 3,341
|
Wealth of information in the four threads at the bottom of this post.
Lee's FCD (Factory Crimp Die) performs two functions. Crimping and post-sizing. The two operations are independent of one another and cometimes work at cross-purposes. With lead bullets, sometimes the post-sizing reduces the grip the case has on the bullet. The grip the case has on the bullet is important for three reasons. 1) It keeps the bullet from being knocked deeper into the case during handling and very important, during feeding. This is most significant in autoloaders 2) It keeps the bullet from being pulled out of the case during handling, and very important, during recoil of its brother rounds. This is most significant in revolvers. 3) It keeps the bullet from moving out of the case until a threshold of pressure has been reached. This is most significant with slow powders, but important with all powders. In taper-crimped cartridges as well as roll-crimped cartridges, the bullet tension (the grip the case has on the bullet) is provided by friction more than by (roll) crimp. If you post-size a case onto a lead bullet, the case springs back more than the lead does, reducing bullet tension. This is less problematic with jacketed bullets than with lead, but can occur with either. If your dies are adjusted correctly, the Lee FCD will NOT post-size your loaded cartridges. You will be able to tell if it is by carefully feeling the resistance as you run the cartridge into and out of the die. The main reason for the existence of a crimp die that operates separate from the (usual) seat/crimp combination die is to simplify installing and adjusting those dies and to prevent the case mouth from digging into the sides of bullet as it is being seated. (This can happen with a strong crimp - mainly roll crimp - on a bullet while it is still being pushed deeper into the case by the seating plug. This is virtually unavoidable with the combo die, but if it is moderate presents no problem.) Not necessary 99% of the time, but convenient. Lee Precision's thoughts on the matter can be found in these threads: One thread contains a lively discussion of the FCD and the function of the post-sizing carbide ring in the FCD. The phrase "9mm" is in the thread title, but don't let that dissuade you. It contains responses direct from Lee Precision, too. Read the whole thing. It is worth it. http://thefiringline.com/forums/showthread.php?t=465091 this thread contains a poll http://thefiringline.com/forums/showthread.php?t=465603 Lost Sheep The Virtue and the Vice http://thefiringline.com/forums/showthread.php?t=509934 http://www.thehighroad.org/showthread.php?t=691050 http://www.rugerforum.com/phpBB3/vie...?f=11&t=168362 http://rugerforum.net/reloading/6586...tml#post814465 |
February 10, 2015, 06:08 AM | #9 | ||
Senior Member
Join Date: February 5, 2015
Location: Indiana
Posts: 125
|
Quote:
Quote:
|
||
February 10, 2015, 09:25 PM | #10 |
Senior Member
Join Date: December 6, 2013
Posts: 246
|
lost sheep, thanks for the info. so i was right about how the combo die was potentially working, as you pointed out, was a possible digging in to the bullet.
__________________
"If you think it's expensive to hire a professional to do the job, wait until you hire an amateur." Red Adair |
February 11, 2015, 04:50 PM | #11 | ||
Staff
Join Date: March 11, 2006
Location: Upper US
Posts: 28,850
|
Quote:
Quote:
The bullet is NOT pushed deeper into the case, cases are pushed up over the bullet. When you run the case with the bullet into the die to seat the bullet, the seating stem stops the bullet, and then the case is pushed up around it. When the bullet seating depth is correct for the crimp, the crimp groove is level with the crimping shoulder in the die body, so that when the case is bent by the die shoulder (roll crimp) it goes into the crimp groove on the bullet. If your cases are digging into the bullet, you have the die adjusted to begin crimping "too soon". in order for seat and crimp in one step to work properly, cases must be the same length, and the seating die must be correctly adjusted. Do that, and you are golden. Don't get it quite right, and you have a host of irritating things, like buckled shoulders, wrinkled case necks, and rounds that will not chamber.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better. |
||
|
|