The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools Search this Thread
Old June 21, 2009, 02:44 PM   #26
Thermodyne
Senior Member
 
Join Date: June 2, 2009
Posts: 111
Big loads of #9 shot with light loads of powder. Chamber bore, and lot of practice until you get used to the slow loads.
Thermodyne is offline  
Old March 17, 2012, 06:37 AM   #27
brooksironworks
Junior Member
 
Join Date: April 27, 2011
Posts: 8
Dave, Please elaborate the POC

"With a load of 7.5s, 10 Points Of Constriction work for trap singles when it's cold, 15-20 POC when warmer.

Skeet demands at least 8s,8.5s or 9s with 0,5 or 10 POC."

what is your starting point? cylinder..........

[email protected]
brooksironworks is offline  
Old March 17, 2012, 09:34 AM   #28
Dave McC
Staff In Memoriam
 
Join Date: October 13, 1999
Location: Columbia, Md, USA
Posts: 8,811
Be careful what you write on the Net, it becomes immortal and can haunt you....

A Point Of Constriction is .001. A Thousandth of an inch.Choke is measured thus.

Depending on who you ask, Cylinder has NO POCs. It's a true cylinder from the forcing cone in front of the chamber to the muzzle. POCs occur close to the muzzle,

Improved Cylinder has 10, Modified 20, Full 30 and Extra Full 40.

Skeet chokes can have negative choke, being bigger diameter, not smaller than the bore. Some skeet chokes have a bit of choke, say 5 POC.

Hope that sorts things out, holler if there's more 'splaining needed...
Dave McC is offline  
Old March 17, 2012, 07:54 PM   #29
TheKlawMan
Junior member
 
Join Date: June 23, 2009
Location: Orange County, CA
Posts: 2,149
I can't see the dust, but about 2 or three in a hundred hopped a good foot or more straight up in the air the other day and I didn't see any pieces fall. Thus, they were lost birds and they told me to I was hitting too low.
TheKlawMan is offline  
Old March 17, 2012, 10:52 PM   #30
zippy13
Senior Member
 
Join Date: August 23, 2008
Location: SoCal
Posts: 6,442
Quote:
...hopped a good foot or more straight up in the air the other day and I didn't see any pieces fall.
Don't you just hate it when that happens?
zippy13 is offline  
Old March 17, 2012, 11:37 PM   #31
olddrum1
Senior Member
 
Join Date: March 23, 2008
Location: Mid Missouri
Posts: 807
Its all that cheap rubber shot your using.
olddrum1 is offline  
Old March 18, 2012, 12:34 AM   #32
.300 Weatherby Mag
Senior Member
 
Join Date: September 6, 2008
Posts: 1,777
12 gauge #9 1 1/8 oz AA loads smack them pretty good... Especially out of an XS Skeet
.300 Weatherby Mag is offline  
Old March 18, 2012, 03:53 AM   #33
TheKlawMan
Junior member
 
Join Date: June 23, 2009
Location: Orange County, CA
Posts: 2,149
Quote:
Its all that cheap rubber shot your using.
I think it must be a mean streak that runs in the Citori line. Like the .410 that laughs at BigJim, mine is particularly myrthful given all the opportunities it has too humiliate me..
TheKlawMan is offline  
Old March 18, 2012, 03:55 AM   #34
TheKlawMan
Junior member
 
Join Date: June 23, 2009
Location: Orange County, CA
Posts: 2,149
Quote:
...hopped a good foot or more straight up in the air the other day and I didn't see any pieces fall.

Don't you just hate it when that happens?
It's as though those clays are bewitched!
TheKlawMan is offline  
Old March 18, 2012, 02:32 PM   #35
zippy13
Senior Member
 
Join Date: August 23, 2008
Location: SoCal
Posts: 6,442
Quote:
How do you "dust" clay pigeons?
A feather duster?


Quote:
It's as though those clays are bewitched!
My friend, you're just now figuring that out?
zippy13 is offline  
Old March 18, 2012, 05:41 PM   #36
TheKlawMan
Junior member
 
Join Date: June 23, 2009
Location: Orange County, CA
Posts: 2,149
Zippy's picture of a feather duster was the final straw. Out of respect for this august board, I tried to restrain myself from mentioning how I preferred my pigeons to be dusted. The ultimate manner is with a feather duster wileded by a comely young thing in a skimpy maids uniform.
TheKlawMan is offline  
Old March 19, 2012, 07:12 AM   #37
mo84
Senior Member
 
Join Date: February 27, 2011
Location: Michigan
Posts: 257
Full choke 10 gage does it well. Full choke 12 gage works too. You just have to hit it right
mo84 is offline  
Old March 19, 2012, 11:29 AM   #38
zippy13
Senior Member
 
Join Date: August 23, 2008
Location: SoCal
Posts: 6,442
A Skeet choked .410-bore does the trick,
Quote:
You just have to hit it right
zippy13 is offline  
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:31 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.07936 seconds with 8 queries