|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
February 22, 2007, 08:54 PM | #1 |
Senior Member
Join Date: June 27, 2004
Posts: 2,011
|
HS-6 safe to download in .44mag?
Starting load for HS-6 240gr JHP bullet is 12gr. I’m using 245gr copper plated/ CMJ. Is it safe to down load to say 10gr? I know .44spl max load (240cast) is 8gr…
PS: I know I can use other/ligher load powders but would like to stay with HS-6 for now...
__________________
"I feel the Beretta is a great character, it's so strong and elegant. The other guns look dumb to me." - John Woo |
February 23, 2007, 03:09 AM | #2 |
Senior Member
Join Date: July 10, 2005
Location: So. Cal.
Posts: 401
|
Straight from Hodgdon's own website:
240 GR. NOS JHP 240 HS-6 12.0gr. 1144 22,800 CUP 15.1gr. 1417 38,200 CUP It MIGHT be safe to download it that far. But I'd suggest you try downloading it 1/2 a grain at a time. At 10 gr. I'd think you'd get around 950 fps. But again, try loading 6 rounds each at 10, 10.5, 11, 11.5, 12, and 12.5. Then fire them backwards from 12.5-10gr. BTW, if you are using cast lead (the load data above is for a JHP), cast loads are typically 10% or more downloaded compared to JHP. In any case, I think you'd be fine at 10gr with a hardcast bullet. Nonetheless, I'd work it up as noted above. BTW, .44 special loads: 240 GR. CAST LSWC 240 HS-6 6.5 761 7,500 CUP 8.0 917 13,000 CUP
__________________
Robert N. "Remember, Eagles may soar but Weasels don't get sucked into jet engines!" |
February 23, 2007, 12:22 PM | #3 |
Senior Member
Join Date: May 11, 2002
Location: high up in the rockies
Posts: 2,289
|
HS-6 is a relatively slow burning powder. I would be hesitant to use it in charges lower than book minimum.
I use HS-6 for virtually all of my 9MM, .40, .45ACP .45 Colt, and .38 special loads. But I load to +P or +P+ specs, and it works quite well. For downloading, I think I'd go to AAC#2, Bullseye, 231, N100 or something else in that burning rate range.
__________________
If you think a mighty military force is expensive, wait 'til you see what a weak one costs. |
February 23, 2007, 01:49 PM | #4 | |
Senior Member
Join Date: June 27, 2004
Posts: 2,011
|
Quote:
The 245gr copper plated bullet I'm usung has a pretty short taparing (bullet photo here) so I can probably seat it deep enough in the magnum case to match OAL of .44spl round (1.450") any reason not to do this? btw cheygriz what is you HS-6 +P load for 9mm 124gr?
__________________
"I feel the Beretta is a great character, it's so strong and elegant. The other guns look dumb to me." - John Woo |
|
February 23, 2007, 03:34 PM | #5 |
Senior Member
Join Date: May 11, 2002
Location: high up in the rockies
Posts: 2,289
|
I kinda hate to post this, because it's just a bit over some books' maximum. I use 115 GR Remington FMJ bullets with Remington 1 1/2 standard small pistol primers in WCC MilSurp cases, with 7.5 GR of HS-6. Chronograph rsults in my Glock 17, Beretta 92, and SIG P226 runs 1325 to 1350 FPS average. About 1300 in the smaller SIG P239.
I get +P+ velocities, but case life seems to indicate only +P pressures. (That's what I love about HS-6. An excellent pressure/velocity ratio) Safe in my guns, but over max in some manuals. Work up to this carefully. I've not worked up a load with the 124 grainers.
__________________
If you think a mighty military force is expensive, wait 'til you see what a weak one costs. |
|
|