|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
September 17, 2009, 10:25 PM | #1 |
Member
Join Date: April 8, 2009
Location: Arkansas
Posts: 86
|
What happened? Seating die tore case...
I'm new to reloading but have successfully loaded about 700 rounds of .38 spl.; 158g LSWC, 125g SJHP, 125g copper plated, and fired over 100 of them through two different guns with no problems. Today, however, I decided to load some 148g wadcutters for the first time and immediately ran into a problem.
Using RCBS carbide die set and was attempting to set my OAL for wadcutters...Hornady .358, 148g HBWC, OAL 1.180. I didn't change my crimp setting (which was set light for minimum loads) and put a wadcutter into the slightly belled practice case to set the OAL. I ran it into the die two or three times, adjusting it deeper each time. The last time I lowered the cartridge, the wadcutter was still in the case but the top 1/8th of an inch of the case was missing...stuck in the die. Like an earlier poster, I have only the internet and books to rely on so I would appreciate any help you can spare. Thanks, Jack 1. What did I do wrong? 2. Any way to remove the stuck piece of brass other than sending it to factory? 3. Would it be easier to just buy new die? The attached photo shows two previously loaded rounds, empty belled case, and the wadcutter and in the torn case.
__________________
Pay attention...it pays to win |
September 17, 2009, 11:06 PM | #2 |
Senior Member
Join Date: April 14, 2009
Posts: 897
|
maybe the die can't handle wadcutters. I have never loaded them but I don't see the point in having them either. See if you can take off the excess with a shirt or something. Thats what I do with my reloads when I see the lead on the sides for any reason
__________________
1. The gun is always loaded. 2. Never let the muzzle cover anything you are not willing to destroy. 3. Keep your finger off the trigger unless you are ready to shoot. 4. Be be sure of your target and what is beyond it. |
September 18, 2009, 02:59 AM | #3 |
Junior Member
Join Date: September 6, 2009
Posts: 8
|
Are you sure it's not just the lead overlapping on the case?
That's what it looks like. After belling a case, sometimes there is a small ridge on the inside of the mouth that will shave lead and make it overlap. Have also seen where if you belled the case out too far that when you run the case and bullet up into the die, the bell gets squeezed down to where it shaves lead if there's a ridge. Borg ETA did you find the piece of brass that "ripped off"? |
September 18, 2009, 04:03 AM | #4 |
Senior Member
Join Date: January 26, 2009
Posts: 492
|
The case isn't torn, it looks like it is crimping it before it seats the bullet and therefore shaving the lead off the bullet and putting it on the outside of the caseing. Did your dies come with a wadcutter seater?, it is flat instead of cone shaped. That is what happend, you had to screw down your die so far that it was crimping before fully seating the bullet.
Put the different seater in the die and then start from scratch and seat the bullet to the proper length, then back the seater out about an 1/8th of a turn and screw the whole seating die down about an 1/8 of a turn, that should get you your crimp you want and your OAL length. Check your length after your happy with the crimp though. No need to buy a new die as there isn't any brass stuck or torn off. |
September 18, 2009, 12:54 PM | #5 |
Senior Member
Join Date: December 29, 2004
Posts: 3,351
|
Your flare was not adequate, and seating and crimping wad cutters at the same time rarely works well.
The bullets are VERY soft. You might want to look into a Lyman 'M' die for flaring. They are not as hard on brass as the stock die extending case life. |
September 18, 2009, 01:05 PM | #6 |
Senior Member
Join Date: November 17, 2008
Location: NW Ohio
Posts: 1,399
|
I agree with all the above. IF you want to convince yourself of it, use your bullet puller and pull that wad cutter out of that case. You'll see it was crimped prior to seating all the way.
If you want to try to get the seating and crimping in one dye, then back off the crimp, and adjust the seating FIRST. Then add the crimp after the seating function is set. |
September 18, 2009, 01:18 PM | #7 |
Senior Member
Join Date: July 31, 2000
Location: Middle Peninsula, VA
Posts: 1,588
|
As others mentioned it didn't tear the case, it just squished the bullet over the crimped case mouth. If you scrape the edge of the bullet you will find the case.
Two ways to prevent that. 1. Seat and then crimp as different steps. 2. If you want to seat and crimp at the same time, first adjust the seating depth, then adjust the crimp. The only way I have found to do this is to back off the seating die so it doesn't crimp at all. then carefully seat a bullet to the correct depth. Back off the seating stem so it doesn't touch the bullet at all, then set the body of the die so it crimps the right amount. Then with the ram up and the round into the crimp position, screw down on the seating stem to contact the bullet again. I usually keep a dummy round made up with my most used lead bullets to make the second method less of a pain. Jacketed bullets are less forgiving so I always seat/crimp them as two steps. |
September 18, 2009, 01:21 PM | #8 |
Member
Join Date: April 8, 2009
Location: Arkansas
Posts: 86
|
Thanks guys, you all nailed it. The case wasn't torn. I was seeing some tiny brass shavings in the seater head and, with the overlapping lead, thought part of the case was missing.
I started all over and everything worked fine...wadcutter seated properly with no lead shaving. I was using the correct/flat seater but apparently was indeed crimping before seating fully. I'll keep playing with it and keep learning. It's nice to have a place to come to for good advice and friendly help. Thanks again, Jack
__________________
Pay attention...it pays to win |
September 18, 2009, 01:24 PM | #9 |
Junior member
Join Date: December 10, 2006
Location: MANNING SC
Posts: 837
|
HBWC
I crimp HBWC in in the top band.for revolver.in the S&W 52 flush with case.
actually they were made for the S&W 52.lyman does not have the wc listed any more. they are quite a projectile if reversed. |
September 18, 2009, 07:09 PM | #10 |
Senior Member
Join Date: August 8, 2005
Location: Arlington TX
Posts: 663
|
When adjusting the seating depth, you need to back out the die so it does not crimp. You crimped the bullet the first time you ran it up into the die, then continued to try to seat it deeper even after it was crimped. Once you back the die out, adjust the seater screw to give you the seating depth you want (without crimping!). Then, back the seating stem out, and start screwing the die body in until it crimps the way you want it (without seating the bullet deeper). Once there, set the lock ring, and then advance the seating stem down until it contacts the top of the bullet (by feel). Lock the seating stem (if it does lock, some don't). Then you are done.
Sure it takes a little longer to adjust when seating and crimping together, but it takes much less time to reload when you do both in one step (assuming you are using a single stage). Taper crimping is a little trickier for me to get set right, but roll crimping into the cannelure is pretty easy once you get the hang of it. Andy |
September 19, 2009, 07:23 PM | #11 |
Junior Member
Join Date: September 19, 2009
Posts: 8
|
You may want to check your primer seating too. It looks like the primer on the empty in the picture is a bit "high".
|
September 20, 2009, 11:41 AM | #12 |
Senior Member
Join Date: February 9, 2005
Location: Owego, NY
Posts: 2,000
|
Interesting thread; are the wad cutter bullets the same diameter as the other bullets in the picture?
__________________
,,, stupidity comes to some people very easily. 8/22/2017 my wife in a discussion about Liberals. Are you ready for civil war? |
September 20, 2009, 05:48 PM | #13 |
Senior Member
Join Date: August 8, 2005
Location: Arlington TX
Posts: 663
|
I don't think it had anything to do with the bullet diameter, but simply that he was continuing to seat the bullet deeper on successive passes, after it had already been crimped in the first pass.
Andy |
September 20, 2009, 06:07 PM | #14 |
Senior Member
Join Date: June 19, 2009
Location: Loadbenchville, Bolt 02770
Posts: 544
|
I agree...
The primers LOOK like they're seated too deep.
Me personally, I strive for 0.004" (4 thousandth's) below flush in all cartridges. Somewhere in the range of 0.003" and 0.005" below flush is best. |
September 20, 2009, 06:40 PM | #15 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,063
|
Once the crimp caught the bullet the seater stem upset the metal to a larger diameter that then flowed out over the bullet as further pressure was applied.
This is an illustration of why separate seating and crimping are easier on the bullet. If you don't want to get a separate crimping die (after which, you always use the seater die too far from the shell holder to cause any kind of crimp, and only use it to put the bullet where you want it), then you need to minimize the travel of a soft bullet like that during crimping and seating. A light target load using a wadcutter needs only a light crimp anyway. The way I used to work with those dies is the same as Big Jake described.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
September 21, 2009, 04:11 AM | #16 |
Member
Join Date: April 8, 2009
Location: Arkansas
Posts: 86
|
latest product
Here's a finished round. Hornady 148g wadcutter seated 1.180 with 2.6g Bullseye. No crimp with seating die this time, light crimp with Lee factory crimp die...first time I've tried the Lee die but seems to look ok.
To answer an earlier question, all bullets are .358 dia.. Haven't fired any yet. Look ok to you guys? Jack
__________________
Pay attention...it pays to win |
September 21, 2009, 06:09 AM | #17 | |
Senior Member
Join Date: May 25, 1999
Location: Too close to Houston
Posts: 4,196
|
Quote:
__________________
Proud member of the NRA and Texas State Rifle Association. Registered and active voter. |
|
September 22, 2009, 11:52 AM | #18 | |
Senior Member
Join Date: December 26, 2004
Location: Louisville KY
Posts: 13,806
|
Quote:
Just a thought. |
|
September 23, 2009, 07:26 AM | #19 |
Senior Member
Join Date: May 25, 1999
Location: Too close to Houston
Posts: 4,196
|
If the primers go in too far it's because the pocket is too deep. Not because you pushed them in wrong. I've never loaded shotgun so I don't know anything about those, but assume the same principle applies.
__________________
Proud member of the NRA and Texas State Rifle Association. Registered and active voter. |
September 30, 2009, 04:04 AM | #20 | |
Senior Member
Join Date: September 19, 2008
Posts: 1,411
|
Quote:
Also, depending on how many cast bullets have been run through the seating die and plug, it may be time to clean out the die as lube and such can build up making the settings a bit inconsistent. Depending on the bullet maker I need to do clean the die about every 700 rounds when loading 38 HBWC. |
|
|
|