July 4, 2012, 09:56 PM | #1 |
Senior Member
Join Date: October 24, 2008
Location: GATOR COUNTRY HA HA HA!
Posts: 721
|
T/C New Englander
Shot my 50 cal T/C today with RBs & 80 gr RS Pyrodex, Got great shooting, about 3" @ 50-70 Yards. Not too bad for my old eyes ; ) PS Took lots of animals with that rifle
Y/D
__________________
There's a GATOR in the bushes & She's Callin my name >Molly Hatchett< |
July 10, 2012, 08:55 PM | #2 |
Senior Member
Join Date: December 18, 2000
Location: San Diego, CA
Posts: 100
|
Nice.
I just bought a used .54 New Englander on Gunbroker. Should be here tomorrow. Been looking for a TC peep sight for it, but they are impossible to find.
__________________
NRA Endowment Life Member NRA Instructor, Basic Pistol SAF Life Member AzCDL Member |
July 10, 2012, 11:40 PM | #3 | |
Senior Member
Join Date: January 2, 2012
Location: Minnesota
Posts: 3,876
|
Quote:
|
|
July 11, 2012, 01:45 PM | #4 |
Member
Join Date: July 31, 2010
Posts: 83
|
|
July 11, 2012, 02:37 PM | #5 | |
Senior Member
Join Date: February 16, 2006
Location: IOWA
Posts: 8,783
|
Peeps are available
Quote:
Be Safe !!!
__________________
'Fundamental truths' are easy to recognize because they are verified daily through simple observation and thus, require no testing. Last edited by Pahoo; July 12, 2012 at 10:04 AM. |
|
July 11, 2012, 02:44 PM | #6 |
Senior Member
Join Date: December 2, 2007
Location: Missouri
Posts: 8,306
|
T/C New Englander is the only M/L rifle I have. The only thing I wish I had done is to have bought the 12 GA barrel to go along with the 50 caliber. They seem almost impossible to find now!
__________________
Cheapshooter's rules of gun ownership #1: NEVER SELL OR TRADE ANYTHING! |
July 11, 2012, 10:27 PM | #7 |
Senior Member
Join Date: December 18, 2000
Location: San Diego, CA
Posts: 100
|
http://www.midsouthshooterssupply.co...?sku=000307194
Status: Out of Stock Expected Date is 3/20/2012 So this will work on the New Englander? I will have to drill the tang though.
__________________
NRA Endowment Life Member NRA Instructor, Basic Pistol SAF Life Member AzCDL Member |
July 12, 2012, 10:15 AM | #8 | |
Senior Member
Join Date: February 16, 2006
Location: IOWA
Posts: 8,783
|
You should be good to go.
Quote:
Be Safe !!!
__________________
'Fundamental truths' are easy to recognize because they are verified daily through simple observation and thus, require no testing. |
|
July 12, 2012, 12:36 PM | #9 |
Senior Member
Join Date: February 16, 2006
Location: IOWA
Posts: 8,783
|
Can do !!
jrp
I physically rechecked both the sight (this sight) and my New Englander. The sight will mount. However, it might take some additional work in drilling and tapping two additional holes as opposed to one. Originally my sight came from Thompson Center and it came with detailed instructions as to how to mount on various SideLocks. Yours should also come with these instructions and if not, or if you need additonal info, get back to me. ..... Be Safe !!!
__________________
'Fundamental truths' are easy to recognize because they are verified daily through simple observation and thus, require no testing. |
July 12, 2012, 07:37 PM | #10 |
Senior Member
Join Date: December 18, 2000
Location: San Diego, CA
Posts: 100
|
Pahoo, thanks much for checking on that. I'll keep an eye out for one of the TC sights. I think 7197 was the model specifically for the NE and 7194 will also fit with a bit more work as you have confirmed.
The Lyman sight is nice, but much larger. I believe I read somewhere that the sight itself or the stock would need to be altered for it to fit.
__________________
NRA Endowment Life Member NRA Instructor, Basic Pistol SAF Life Member AzCDL Member |
July 12, 2012, 07:48 PM | #11 |
Senior Member
Join Date: October 24, 2008
Location: GATOR COUNTRY HA HA HA!
Posts: 721
|
jrp, What load do you use in the .54 cal ? Does it kick much, My 50 cal shoots like a dream. My wifes shot it & hit What she aim at ; ) PS Mild recoil
Y/D
__________________
There's a GATOR in the bushes & She's Callin my name >Molly Hatchett< |
July 12, 2012, 08:06 PM | #12 | |
Senior Member
Join Date: February 16, 2006
Location: IOWA
Posts: 8,783
|
My compliments as you've done your homework !!!
Quote:
Be Safe !!!
__________________
'Fundamental truths' are easy to recognize because they are verified daily through simple observation and thus, require no testing. |
|
July 12, 2012, 10:27 PM | #13 |
Senior Member
Join Date: December 18, 2000
Location: San Diego, CA
Posts: 100
|
Y/D, in the Lyman .54 Trade Rifle, I've shot round ball with from 50 to 100 grains Goex 3f and also tried 80 to 90 grains behind a 385gr. Great Plains bullet just for grins.
Standing, the recoil isn't bad with any of those loads, although the GP bullet loads are pretty stout. Off the bench, my cheek gets slapped by the stock if I go much above 70 grains. I typically shoot 60-70 grains and round ball at paper, cans and steel plates. I've been shooting cap and ball revolvers since late last year, but just got the Lyman a few months ago. Between BP and .22LR, I'm barely shooting my centerfire guns any more these days. I will take the New Englander out for the first time next Friday. I'm thinking the flatter stock and butt plate may be more comfortable off the bench than the Lyman. Pahoo, I've been looking at the various Pedersoli tang sights. What do you think of those? They are kind of pricey. If I can't eventually find a TC sight, I'll have to decide between the Lyman 57 and a Pedersoli. I would modify the Lyman like you did rather than alter the stock. ETA: I stripped the New Englander and found 2 dabs of silicon gasket type material under the lock. I guess this is a later built rifle when TC QC was getting spotty. I've read about other people finding the same "fix" under the lock. I'm guessing TC had a run of stocks with the mortise cut too deep?
__________________
NRA Endowment Life Member NRA Instructor, Basic Pistol SAF Life Member AzCDL Member Last edited by jrp; July 12, 2012 at 10:37 PM. |
July 13, 2012, 10:04 AM | #14 |
Junior member
Join Date: June 20, 2012
Posts: 12
|
Joe,
Dixie Gunworks is where I recently got my TC peep sight. Everyone else is out of stock and at this moment TC is not making them. http://www.dixiegunworks.com/product...oducts_id=7517 |
July 13, 2012, 10:57 AM | #15 |
Senior Member
Join Date: November 20, 2007
Location: South Western OK
Posts: 3,112
|
This year Ft. Sill will require conventional muzzleloaders for the first week of ML deer season. Bought a very nice New Englander .50 caliber a few months ago for $150. Went to sight the gun in with 370 grain Maxi-Balls and found out it was on target at 50 yards. My powder is 100 grains of Pyrodex RS. The primer is Winchester magnum #11.
Problem is my eyes are old and i have trouble finding the bead on the target: Put some orange traffic paint on the bead and it helped some. Best i could do was 2" groups at 50 yards. |
July 13, 2012, 02:16 PM | #16 | ||
Senior Member
Join Date: February 16, 2006
Location: IOWA
Posts: 8,783
|
Quote:
http://www.dixiegunworks.com/advance...+sight&x=5&y=5 Quote:
It was dark brown; wasn't it ?? I guess one might say that this is common and not exclusive for TC. I have a pretty good idea as to why they did this. You will also find this stuff under the tang and sometimes trigger guard. Stock shinkage adds to the problem. .... Be Safe !!!
__________________
'Fundamental truths' are easy to recognize because they are verified daily through simple observation and thus, require no testing. |
||
July 22, 2012, 01:00 AM | #17 |
Senior Member
Join Date: December 18, 2000
Location: San Diego, CA
Posts: 100
|
I took the (new to me) .54 New Englander to the range for the first time last Friday. Shot nice, no problems at all. Shot about 20 rounds of .530 ball, .015 patches lubed with Crisco at short distances (we were on a plinking/tac range, not the 100yd. rifle range) .
The stock fit well and didn't slap me in the face like the Lyman tends to do. The factory open sights were fine, although I'd still like to eventually put a peep on it for 50 and 100 yard shooting (my eyesight isn't too good). However, I must say that I don't like the QLA muzzle. I found it harder to load than a standard barrel. With my Lyman Trade Rifle, I can exert maximum force with the stubby end of the short starter to initially get the ball seated. With QLA, I can't use the stubby end to seat the ball. Because of that I found I had to pound on the starter with the palm of my hand to get the ball seated. I'm sure the seating effort will get somewhat easier as the gun breaks in (I don't think this gun has been shot much), but my first impression of QLA is not favorable. But overall I really like my NE. My shooting buddy, who hasn't shown much interest in my Trade Rifle, offered to buy my NE (nope!) and last I heard was looking at NE's on Gunbroker!
__________________
NRA Endowment Life Member NRA Instructor, Basic Pistol SAF Life Member AzCDL Member |
July 22, 2012, 09:48 AM | #18 | |
Senior Member
Join Date: February 16, 2006
Location: IOWA
Posts: 8,783
|
Trading off one nuisance for another !!!
Quote:
Be Safe !!!
__________________
'Fundamental truths' are easy to recognize because they are verified daily through simple observation and thus, require no testing. |
|
July 22, 2012, 12:21 PM | #19 | |
Senior Member
Join Date: March 15, 2005
Location: Central Connecticut
Posts: 3,166
|
Quote:
A guy on another forum posted photos showing how he cut off the QLA section of an older TC inline rifle and then re-crowned the barrel all by himself. That's an idea to consider. Why keep the QLA if all it does is cause loading problems? It's simple enough to get rid of and almost any gunsmith will do it. |
|
July 22, 2012, 05:18 PM | #20 | |
Senior Member
Join Date: December 18, 2000
Location: San Diego, CA
Posts: 100
|
Quote:
I haven't tried a conical in the NE yet, but I'll bet its much easier. Unfortunately I mainly shoot RB. One member PM'ed me to suggest using a .010 patch for ease of loading, especially when I'm on the short-distance plinking where a small accuracy/velocity loss wouldn't matter. That sounds like a good idea to try.
__________________
NRA Endowment Life Member NRA Instructor, Basic Pistol SAF Life Member AzCDL Member |
|
July 22, 2012, 07:11 PM | #21 | |
Senior Member
Join Date: February 16, 2006
Location: IOWA
Posts: 8,783
|
Maintain the fun factor !!
Quote:
Be Safe !!!
__________________
'Fundamental truths' are easy to recognize because they are verified daily through simple observation and thus, require no testing. |
|
|
|