|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
January 19, 2013, 09:53 AM | #1 |
Senior Member
Join Date: April 22, 2007
Posts: 1,996
|
CZ 527 varmint scope mounting options
I'm picking up a CZ 527 varmint in 223 and I'm looking for a 30 mm one piece scope mount for it. I checked DNZ, but they don't have any CZ mounts. What is a solid mount for ~$100?
Last edited by wnycollector; January 19, 2013 at 10:01 AM. |
January 20, 2013, 12:45 AM | #2 |
Senior Member
Join Date: May 28, 2007
Location: Santa Cruz, Ca.
Posts: 204
|
Your 527 is set up to take 16mm dove-tail rings.
If you intend to use a one-piece mount, you will need to drill & tap the receiver. I have a 527 and use Warne Maxima Permanent steel vertical split rings, it's a very solid set-up. Should you decide to go ahead with a one-piece mount, I've used a couple of Ken Farrell mounts, on Savage varmint/tactical rigs, that I liked very well. Link to Ken Farrell - http://www.kenfarrell.com/CZ-527-VARMIT-1-0.html Good luck, Bruce CZ527 Varmint w/ Bushnell Elite 4200 6-24x40 & Warne Maxima rings. |
January 20, 2013, 07:02 AM | #3 |
Senior Member
Join Date: September 10, 2007
Location: Racoon City
Posts: 934
|
CZ_Ringmounts_list_.pdf
This attachment has all the CZ ring mounts that I am aware of. On my 527 Varmint, I chose the CZ branded rings. |
January 20, 2013, 08:47 AM | #4 |
Senior Member
Join Date: January 2, 2009
Location: Northern Virginia
Posts: 922
|
I have two CZs with the dove tail mounts and after using the CZ rings on my .223 I found that the flat screw slots on the CZ rings were not easy to torque. I decided that I would go with Burris Signature rings with the plastic inserts and Torx screws on the rings for my CZ 550 in .30-06. You can get them in the dove tail mounts.
The rear ring on both the CZ and Burris ring sets have a lug that keeps the ring from slipping. Either work fine and are very stable. |
January 20, 2013, 06:35 PM | #5 |
Senior Member
Join Date: March 26, 2005
Location: Osborn, Missouri
Posts: 2,697
|
If you don't find the mount you want I have a pair of 30mm rings that fit the CZ 527 model rifles.
If you are interested in them you can e-mail at [email protected] . Best Regards Bob Hunter www.huntercustoms.com |
January 21, 2013, 09:48 AM | #6 |
Senior Member
Join Date: April 22, 2007
Posts: 1,996
|
Thanks for the help folks!
|
January 21, 2013, 02:28 PM | #7 |
Member
Join Date: May 25, 2012
Location: Down South
Posts: 95
|
I went with the Talley rings on my 527 and like them. I'm not sure they come in 30mm. Mine are 1" It want hurt to check. They are very nice rings.
Last edited by mike7.62; January 21, 2013 at 02:38 PM. |
January 21, 2013, 10:02 PM | #8 |
Senior Member
Join Date: December 10, 2012
Posts: 6,165
|
Talley makes good stuff. Made in South Carolina.
|
|
|