December 19, 2014, 03:44 PM | #751 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
No- I got to find some to try.
Guys asking about using 585 CEB bullet in our 12ga super sabot. Here is picture, We just took off the bottom band and couple middle bands on the CEB and it fit perfect in our 12ga sabot, which uses .575" slugs. Hollowpoint one pictured 700gr in the sabot loaded in brass case. Can be used in plastic case with a special made hollowed out long roll crimper. Getting some more interest in our 585HE. An application for our 585 HE is for guys with old military 14.5mm PTRDs, to use our case with chamber insert. In many places 14.5 cases are scarce, real expensive, as well as most 14.5mm cases being steel are not the easiest to resize/reload. Our case sizes like regular cases and can be easily reloaded many times. And a PTRD with almost a 5 foot long barrel could get 650gr spitzer bullet to about same speed the 14.5mm gets a 900 gr using 3 times as much powder. About 3300 fps. Or get a 900gr at 2800. Great possibilities for fun shooting. For tactical use in a place where it would be useful to reload in the operations field, where steel cases are scarce. 100 of our cases do over 2000 reloads. I like Enfields to put our 585HEs in, for reasonable cost guns, the actions once sporterized are one of the longest for long cases. . Here is inexpensive way to fancy up the Enfield Bolt handle by cutting the dogleg part of the old handle off and welding on inexpensive contoured handles I found, one of which is like Ruger 77 handle, the one on the right . Something even a novice like me can do..... A lot of guys are crazy about CEB bullets. Here are light 450gr ones in our 24ga FH. That hollowpoint can range in weight 450gr to 700gr depending on how much we cut off the back.. The 24ga FH brass case is nice complement to our 585HE, for shotgun only deer hunters that want a .585" caliber, and easy to find big bore bullets.... Ed
__________________
ED HUBEL |
January 3, 2015, 04:19 PM | #752 |
Senior Member
Join Date: December 14, 2011
Location: WV
Posts: 938
|
I seen on another forum you show a NEF 10 gauge converted to an 8 gauge. I don't know if you have mentioned here. How well does it perform? As good as a real 8 gauge? Can any gun smith do the conversion?
|
February 14, 2015, 10:32 AM | #753 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
I bored it out by hand. not the best job, took a week.
Can be done better by shop with deep drills and reamers, if you can finds one with tools. For lightweight plinking, deer hunting, etc, in 585HE as well as 24ga FH here is picture of 58cal Hornady sabot that holds .451/.452" light bullets 225 to 300 gr. A way to shoot targets economically. Low recoil but a big bang and satisfaction. A 250 gr bullet would go about mach 4 with a top load.. Here is what 585 bull barrel, target blank looks like, 1 5/8" OD and 32" long. It'll go in heavy action of some kind. 4th one from the left. The one in yellow sleave on top, is a heavy contoured one with muzzle of .980". we got a bunch of them and so does McGowen. Here is picture, nice cast bullet I like for the 585HE and 24ga FH. It is .585" diameter and 650 gr and these particular ones are a hard lead alloy, plus they've been heatreated. They are about as hard as copper jacketed softs pivtured. These in .575'' size would work in our 12ga sabot.. But to penetrate good and do great damage to game or target they can be fairly soft lead and hollowbase like Minie Bullets. Here is picture of timber drilled through with .585 soft lead Minie from 585HE. Picture is the back of 6x6 timbers where Minie bullets came out. Guys experimenting with multiple ball loads in 12ga wadcups, here is a way to keep them together group wise.Ed
__________________
ED HUBEL |
April 21, 2015, 09:18 PM | #754 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
Here is picture of our NEF 12ga FH with Hogue Compstock. It has the
recoiling cam and springs in the hollow butt plus some weght, Here is a variety of slugs and bullets that fit in a 12ga dangerous game slug, lock on sabot. BPI sells it . There is couple 585 videos on Swann Gunsmithing's Facebook site; Of our 585HE in first Ruger #1, that was done in Australia.It was set up for the poster Tankhunter on the AR big bore forums. That gun killed the first AUS buff, killed by a 585HE, that I posted picture of above. You can go direct to the page and click on the videos to watch the test firings.. https://www.facebook.com/swanbarrels/videos Here is picture our 585HE in a Montana PH action in a MPI stock, with the style of a CZ stock and metal will be finished with a Gun Kote finish. Here is picture of a 585HE we did in a Mauser 98 as a singleshot test gun. We used a composite stock we adapted to fit action. Weighted to 12 lbs. Enfield in back, you can see it is longer. And speaking of singleshots a fellow in the Yukon is just finishing up one in a Ruger #1...ED
__________________
ED HUBEL |
June 26, 2015, 05:24 PM | #755 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
The 12ga FH isn't the first wildcat case built on BMG brass, it was preceded by
target rounds like the necked down 338 Talbot, the cut off 700 DKT for big game, necked down to .416 and . 458, and more, but the following one was way before them, in my favorite rifle caliber, for .585" bullets. One of first modern era 585 caliber wildcats, since WW2, the 575 Miller-Greiss Magnum, was first mentioned in the fifties, It was made from BMG brass shortened to 2.70" long and necked up from 50 cal to .585". But actually if cut off first, it would be annealed, necked down to hold 585 bullet. Fairly sharp shoulder. They rebated the rim quite a ways down to .618" to maybe fit 98 Mauser bolt. Maybe used a special hogged out, reworked action. Listed as shooting 750gr bullet about 2400 fps. It holds about 150gr of ball powder under a 750 gr bullet, maybe little less than 3" 50cal spotter case, where our 585HE holds 180gr under a 750gr'. We made one for experimenting on a full length BMG case.With rim left same as the base and would need a BMG or PH sized bolt and action. I'm glad to be a big bore wildcatter, and happy to be in the company of big bore nuts, old and new. Years ago when guys did big wildcats on BMGs, they took what was available, full length BMGs to rework, and but maybe back then they could have used the 3" BMG spotter case, by shortening the neck, if they could have found couple barrels full. But it takes a lot of work to reform and shorten cases that much like M&G, with the multiple dies, multiple annealings, and case trimming and extreme reworking of regular rifle actions, which is why I like our 585 case, simple and straight, any regular, long bolt action, or falling blocks, break actions, etc, a 585 good for dozen or more heavy loadings, and moderate loads, last forever.. For our 585HE , made it a size, actually new belted size, to fit regular size, long bolt guns, (not BMG actions)that didn't have to be used from tripod so to speak, and could be put in a favorite gun of many, the Ruger #1, other falling blocks, without taking metal out of the feed trough. To get the same and/or more powder space as a cut back, really shortened, BMG case, like M&G, wildcatted to 585, or other short cases, we made longer case and worked with guys with a group buy, to get a factory run made. A miracle. We thank all gun nuts for the help. Here is picture from the great site, cartridgecollector dot net, of the M&G Mag .Ed
__________________
ED HUBEL |
September 1, 2015, 11:05 PM | #756 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
Sorry to be away so long. Health and money problems.
Here are couple 24ga FHs in break actions, a CBC with monoblocked 585 barrel in it, and a guys NEF he had a 585 barrel monoblocked in. The 585 barrels are perfect fit for 24ga and 585 Minie Bullets are a perfect for barrel and 24ga case fit. Another matter--- I know it seems like I'm begging for help when I ask guys on the net for help at times. . But I really am in a bind. That is truth, Our small income disappeared from our farms truck garden business as my my knees are shot and can't hardly walk, I can't do field work, etc. And the wife's lung condition got so bad she can't work, nearly invalid. So we finally had to quit that, but were and are in debt. We need little extra money to try to keep our health fixed up and pay bunch of back bills and utilities. As well as needed to pay for traveling to doctors, treatments,drugs, etc. Could you all maybe get together with others on these forums and kinda take up a collection to help get me out of my troubles and debt. Like 10 or so bucks each put into my paypal account as gifts. And if you want to mail it, use email below to contact me to get you my mailing address. The Paypal email is [email protected] Best Regards- Ed PS-- I really need help. Not astronomical amounts, but fairly fast. Just a little from each to help. We never made anything on the 12ga FH, etc, work and research. The little coming from sale of our groups buy of 585 brass, dies, barrels, etc, goes to pay to the places, where the money is owed, for getting them made..Ed
__________________
ED HUBEL |
September 24, 2015, 03:29 AM | #757 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
Sorry to be away so long, health, getting old, and interruptions.
Here is picture of a lightweight Barnes bullet in 24ga FH. Guys cut the back off of 750gr bullet off to get 500gr weight. Here is picture 58 cal Minie slug that's little long on the side for our 12ga sabot, with the front of the slug above the grooves swaged to fit in sabot. The swaged front third of the slug fits next to the internal ridge in sabot and the sabot doesn't bulge out.Just run front into a die and punch it back out. And some info about 12ga FH and other hopped up shotgun slug loads, You know we like to use the rifle, IE slower than shotgun, powders. We like to use IMR 4759 for some loads and RE17 for others where we have room for larger charges. Those two powders are ignited ok in large diameter cases like 12ga, 10ga, 16ga, etc, without needing BMG primers. But we have always been looking for easy to ignite powders of the RE17 type, when cold, that has a speed between IMR 4759 and the RE17. RE17 uses different process to put the deterrents in the powder to control speeds, which allows much easier ignition, compared to big majority of rifle powders with all the deterrent on the outside. There are some out there made by Nitrochemie Switzerland, who makes RE17, RE26, RE33, etc, for Alliant. It's the ' RELOAD SWISS' brand available for those in UK and Europe, They are called RS 40, about same speed as RE12, RS 50 & 52, same speed as RE15, RE60 & 62 same as RE17. Also one ' Vihta Vouri ' powder called TR140 available over there, that Nitrochemie made.. Many guys can't get IMR 4759 anymore, some can't get RE17. I'd like to get some of RS 40-50-52 powders or V V TR140 into the states, would really be great help for hairy slug load work. And guys in UK/EU now can load some real hairy slug loads..Ed
__________________
ED HUBEL |
October 23, 2015, 10:18 AM | #758 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
We got guys wildcatting our 585HE case,
Here is picture of that 375 Warlord next to our 585 case he made it from. He is going to make couple later necked down to 416, and 458. There is another guy working on doing one necked down to 357 wildcat. Here is a picture of our poster Biebs on AR, 585 HE, in a MPI stock. He used a big Enfield action, with a fancy jeweled bolt. We found couple other big actions for our 585, that can even feed really long overall length loaded cases, like 4.5" long or more, if you are using long pointed bullets for real long range target and hunting work. One is Lawton 8000 Cheytac action, and the other is Stiller Cheytac actions made similar, just a newer version. Both actions come in 1.45" diameter and a 1.60" diameter receivers. And Vestals Gunsmithing in Virginia does great work, decent prices, has these actions and will build you fancy 585 HEs. .. He has, working with another guys mag box setup, setup an extra long, good working, single stack, center feed, magazine..He has one of our 585 HE reamers on hand, we have barrels....Ed
__________________
ED HUBEL |
November 9, 2015, 02:20 PM | #759 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
Here we kill two birds with one stone so to speak,
Best case sizer is the MEC Collet Super Sizer and it can double as a case holder when we roll crimp. Much better hold than the ones made to hold cases for crimping, that cost a lot. Save cost of a holder, plus have best sizer around Here is couple different setups our guys checking for our 585HE in a long, Lawton Cheytac action. First laminated thumbhole stock. Second in a Hogue Compstock. The action can mount a scope rail like shown on the table in 1st picture or a receiver sight in 2nd picture. The scope rail is a piccatiny type. The stocks used were wide ones for REM long actions, just add recoil block ahead of recoil inleting for the longer action, drill new screw hole Open the stock forward to original bolt hole for longer cases and mag. About Enfields for our case, one of my favorites, Some don't like the sporterizing, welding bottom metal straight. Many think straightening is a huge job needing special jigs. Easier just use one being added on for a jig with a bolt, to weld on the straight extension, Do top weld, then cut old extension that is under off with a thin cutting wheel, then weld bottom. When we bolt the short piece on the one we are straightening, we grind the short slant off so the added piece lays on there flat. The one you cut off can be used as the top extension for the next one!!! Just keep on building...Ed
__________________
ED HUBEL |
December 10, 2015, 02:11 AM | #760 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
Here is a fancy stocked 24ga FH built on a NEF, built by
a guy in Canada. Its straight back, high comb stock, handles recoil great.Neat looking work... Ed More about 585 BB case for lever guns, pistols, AR Uppers, Work in 71s, later 1886s, Henry steel frames made for 45-70. One guy is putting one in single shot action set up with Contender style pistol grip for testing in long rifle barrel, to simulate pistol recoil..Be very brisk recoil in a case that holds 110 gr powder under a light Minie bullet Maybe work in a Rossi Judge with heavy barrel. Or rolling block rifles and pistols...Gonna try one in 1887. Got first one in one of our guys Greener GP. In some ways big bore shotguns and rifles are sexy. By looking at the shape of the fire and smoke cloud.... Thanks for picture, to the great NitroExpress Forums site. Here is picture of another neat sporterizing deal for Enfields. On those without rear bridge pocket welded up, we just mill down and shape it so debth of the pocket matches bottom section of weaver rail and screw or epoxy it in. Shape to drive in hole tight. Can use as a rear scope ring mount or mount for peep sight like a compact UTG sight...Ed
__________________
ED HUBEL |
January 24, 2016, 11:15 AM | #761 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
A poster reading our threads said '' I'm slowly becoming a recoilapheliac''..
That is neat term , and very glad that folks are catching the big bore fever. Here is a simple, yet neat peep sight we can use on the rear sporterized bridges of Enfields, works on other rear bridges also.Including shotguns. I like peep sights the best for most shooting. They also come with flat bottoms also for bridges and receivers that are flat on top. Here is another pic of our guys 24ga FH in the NEF On straight sided cases like our 585 HE the die set has a mouth expander die to make it easy to insert bullets. The die flares the mouth, but I always felt that doing what is really a relative relatively sharp flare, and then the slight roll crimping the same area of the case into a groove on the bullet or slug, shortens case life. So I just use expander plug out of the die, by hand, using just the bottom of of the expander plug and just push it in a little, wobble it around a small amount, bullet goes in ok, case mouths last longer, good for dozens of loads, with moderate hunting and target loads.Only takes a few seconds and less work that has to be done in the press ... Ed
__________________
ED HUBEL |
February 12, 2016, 03:27 AM | #762 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
Here is picture of a hard plastic molded shotgun case, holding
a slug, without crimping, a company is experimenting with. This one with light slug supposed to do over 2000 fps. Here is video by Corlanes Sporting, Dawson Creek, BC, CAN. Known as, Rocky Mtn Rifles, video on Youtube of them testing our 585 HE in a barreled action, they are building for a guy. They are shooting it into their big bullet trap with test load.. https://www.youtube.com/watch?v=1vzQjRGfT1A Here is picture of Rossi SS with 585 barrel mono-blocked into it, chambered for our 585 BB 2.17" case, to do testing in a light rifle with just pistol grip to simulate the case in pistols. Others going to put case in leverguns, autoloaders. We got plenty of cases Ed
__________________
ED HUBEL |
March 17, 2016, 01:20 AM | #763 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
Here is picture of a great old time 8bore double.
I like those old outside hammer, big bore guns. The style of most break actions singles aren't the greatest, that we we used for 12ga FH, 10ga FH, other caliber barrels we mono-blocked in them like .585" bore for 585HE and 24ga FH.. One that is close that we have, is the Magtech. Well the guys have found one that is super strong lockup and looks real nice. And has the good quality look. It comes 12ga light shot barrel, soon be monoblocked to rifled 24ga FH, the little brother of the 585HE. We told company if they did them with NEF style, rifled, heavy slug barrel, for shotgun caliber only hunters, they couldn't make them fast enough. Here is picture of 585HE, In an Enfield that Bret and Darrel in Minn set up with great camo finish, with nice brake job. It is in a Hogue, recoil reducing, rubber coated, Compstock.Great job they did.. Ed
__________________
ED HUBEL |
April 13, 2016, 07:45 PM | #764 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
We will have arrived when we have this big bore in our back yard,
Kind of a neat suppressor, Here is folder shotgun guys set up as 24ga FH. Here is another view of what we feel is a nearly perfect break action. Guy is making a strong 24ga FH with it. Here is picture of a 585HE MRC PH a guy set up..Ed
__________________
ED HUBEL |
April 13, 2016, 08:17 PM | #765 |
Member In Memoriam
Join Date: March 17, 1999
Posts: 24,383
|
I wonder if any of our good readers are going to try those rounds in great-grandpop's old Damascus 12 gauge. Should be interesting.
Jim |
April 13, 2016, 10:52 PM | #766 |
Senior Member
Join Date: January 22, 2009
Location: Texas
Posts: 2,753
|
Cool. The zombie thread from hell.
|
April 14, 2016, 11:22 AM | #767 |
Senior Member
Join Date: March 15, 2010
Posts: 8,238
|
I always look forward to the return of this thread.
__________________
Woohoo, I’m back In Texas!!! |
April 14, 2016, 03:24 PM | #768 |
Senior Member
Join Date: January 22, 2009
Location: Texas
Posts: 2,753
|
Its a neat thread. I just haven't figured out what is walking around that needs a cartridge this big. I think over on The High Road forum they moved this thread to the reloading section which seems like a better place for it.
I am kind of jealous. I wish I had something to sell so I could start a thread to promote my product. |
April 14, 2016, 03:30 PM | #769 |
Senior Member
Join Date: January 22, 2009
Location: Texas
Posts: 2,753
|
Nope. Still in the rifle section. I wonder why it has to posted in both forums where everyone on this forum visits the other forum and vice versa?
Oh well, such is life. |
April 22, 2016, 09:07 PM | #770 |
Senior Member
Join Date: August 22, 2015
Location: new england
Posts: 1,159
|
I truely enjoy reading about the guns and cartridges Ed is working on. This stuff can be as practical or as, off the charts, as any one might want. Working with the 585 case, in various lengths and loading it is possible to go from mild 577 black powder, to 577 NE (a proven killer and stopper) to beyond the Trex performance (braggin rights shooter).
I love reading about this stuff. I may do a 585 Hubel someday. It would be nice to see this one in production: http://www.gunownerstv.com/coyote2.jpg |
May 11, 2016, 04:34 AM | #771 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
We just do it like a group buy, no profit ever made.
Here is a Midland break action a guy is doing in 24ga FH. Here is old catalog picture of different stuff used in old days for shotgun loads. Some would be hairy in brass cases Here is picture of a MN a guy is doing 585HE in.. It is singleshot. Redid bolt handle mounted it on the bolt further bac, so the port could be lengthened for our long case. Needs polishing and blueing, scope rail added. Ed
__________________
ED HUBEL |
June 18, 2016, 03:27 AM | #772 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
There are guys on Castboolits forum experimenting with
locking on plastic bases securely on slugs. Making their own front heavy ones for smoothbores. Some interesting ideas. Here is picture of our 585BB case next to long 585HE.Ed
__________________
ED HUBEL |
July 23, 2016, 12:08 AM | #773 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
.
Here is a helix driver seal we made by cutting base from helix driver wadcup, good for fullbore roundballs that are too big to go in cup. Best one to cut off is shortest `12ga one BPI has. Here is picture of a 585HE made on a Stiller bolt action for guy in Canada. It was made for the poster Spooksar on Africa Hunting and Accuratereloading, by Corlanes/Rocky Mountain rifles, in Dawson Creek BC Canada, with a Stiller action, Timney trigger. the stock is a blue/grey laminate. He imported the barrel, cases, dies, etc.. from us, through Prophet River in Lloydminster AB. That action similar to Lawton we had and neighbor got, that won the King Of The 2 Mile shoot at Whittington, with the 375 Lethal cartridge the neighbor made, from our 585 brass. Made it full length case,.. It is big one on the right. He made an 18 lb gun with McMillan target stock, a huge scope, tripod.. Nice thing is we don't need BMG action.Ed
__________________
ED HUBEL |
July 26, 2016, 06:29 PM | #774 |
Junior member
Join Date: May 20, 2014
Posts: 1,835
|
LOve you Hubel
|
August 8, 2016, 04:15 AM | #775 |
Senior Member
Join Date: March 8, 2000
Posts: 751
|
Fellow big bore nut, Nathan Vale in AUS, has worked with
Bertram and got the run of full length 12ga From Hell cases done. Drawn 12ga long cases as strong as BMG brass with unbreakable rims. Any wanting to get some, contact Bertram at the email ----- [email protected] ...... Some more on wildcat 375 Lethal....... .375 Lethal Precision Arms LLC rifle shooting prototype solid 400gr Berger bullets. Mitchell built this rifle himself using a McMillan A5 Super Mag stock, Rock Creek barrel, Nightforce ATACR MOA scope, Phoenix Precision Bipod, and a Lethal Precision Arms muzzle brake. Lawton Action. Lethal Precision his own gunsmith shop, will make these target rifles for anyone into target shooting and long range hunting.. Remarkably, Mitchell nailed first- and second- shot hits at the 2477-yard target, a full 1.4 miles away. It is windy out there, makes shooting hard with a time limit. The prototype 400 grain Berger Bullets solid was superb, (G7 BC of 0.56 at 3000 fps). Here is 585 HE in an Enfield, in a Choate Heavy Varmint Stock. These are super strong. The butts of these can easily be weighted. Couple guys doing them....... Ed
__________________
ED HUBEL |
|
|