The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools Search this Thread
Old August 31, 2009, 09:26 AM   #1
ZeSpectre
Senior Member
 
Join Date: June 4, 2007
Location: Shenandoah Valley
Posts: 3,276
DIY Media Separator

I was looking at some items I had around the house and decided to try and make a DIY tumbling media separator based on the professional ones available from Frankford Arsenal and other places.

I already had a red 5 gallon "beach bucket", some PVC tubing, and a few other miscl odds-and-ends but I did have to go over to the local dollar store and buy a pair of "matched" plastic colanders to use as the "tumbling chamber".

First I used a drill powered hole saw to make holes in the bucket and then opened up the top of the holes to give me a place to rest the axle.


Next I clamped the colanders together and drilled more holes so I could run the axle through it.


Then I measured the PVC tube to be an axle, cut to length, and drilled holes for the pins to secure one of the colanders. The other colander was then put in place and two small holes were drilled for the nut/bolt combos that will hold the colander "ball" closed when filled and tumbling.


Then came the moment of truth, a good sized load of .38 Special cases and walnut media.


Wow, this really works well! The media was sifted out and the mechanical action of the brass clashing around also seemed to knock the vast majority of the walnut media out of the flash holes in the brass!

There are a few flaws in the design though.
1) I need to add a lid. The flat edges of the colanders hold media and fling it around as you spin the "sifter ball". A cover would catch this and keep it from going everywhere.

2) I need to epoxy the screws that seal the "sifter ball" and add wingnuts. The current arrangement of loose nut, bolt, and washer, is far too easy to drop into the bucket (and those small screws are hard to find in walnut media).

3) I need to add a crank handle. I can certainly grab the axle and turn the thing but I think having a crank handle would make things much easier.

So the entire thing cost me about $4 for the two colanders and the rest was all parts and stuff I had laying around. Not too shabby and it's going to be great once I deal with the above mentioned design shortcomings.
__________________
"The dogs may bark but the caravan moves on"

Last edited by ZeSpectre; September 1, 2009 at 12:16 PM.
ZeSpectre is offline  
Old August 31, 2009, 11:30 AM   #2
emcon5
Senior Member
 
Join Date: July 10, 1999
Location: High Desert NV
Posts: 2,850
I just took some left over metal mesh and formed it into a bowl shape that fits inside a big plastic bucket. I stir it around with the same pasta spoon I use to remove the cases from the tumbler.

Like this one: http://www.oneida.com/resources/onei...805.zoom.1.jpg

I am sure the Frankfort/Midway one is faster, but it was free, and doesn't take up any more space than the bucket.
emcon5 is offline  
Old September 1, 2009, 12:16 PM   #3
ZeSpectre
Senior Member
 
Join Date: June 4, 2007
Location: Shenandoah Valley
Posts: 3,276
updated and added photos.
__________________
"The dogs may bark but the caravan moves on"
ZeSpectre is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:07 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.04895 seconds with 10 queries