August 3, 2012, 11:10 AM | #1 |
Senior Member
Join Date: June 16, 2011
Location: Ohio
Posts: 1,497
|
Bulk 9mm
Finally ran out of my initial 300 rounds of Hornady FMJs that I bought at local reloading shop just to get up and do function testing - but they are far to expensive for continued use.
I have also been contemplating bumping up to a 124 grain bullet. I would like to do a bulk order at least 500-1000. Any recommendations for good performance in a Beretta 92 provided that I do my part. Am open to FMJ (for the right price), plated, or lead. However this gun has never seen cast lead bullets, so any pointers on how the 92 would perform with them would be helpful.
__________________
"The best diplomat I know is a fully charged phaser bank" - Montgomery Scott |
August 3, 2012, 11:29 AM | #2 |
Senior Member
Join Date: June 25, 2009
Location: Stuttgart, AR
Posts: 1,569
|
Don't have a Beretta 92, but I've been pleased with 124 grain Berry's plated in HBFP and HBRNTP. Can get direct from Berry's or from places like Powder Valley, Graf & Sons, etc.
Also pleased with the groups I got from 115 gr. SB MO Bullet Co. I recently ordered from Powder Valley. While I haven't tinkered with them (yet), there are folks who sing the praises of Precision Delta, Zero and Montana Gold in the FMJ bullet line.
__________________
A lack of planning on your part does not necessarily constitute an emergency on my part. |
August 3, 2012, 11:51 AM | #3 |
Senior Member
Join Date: May 12, 2011
Location: New Mexico
Posts: 1,315
|
I have had good results with Berry's bullets. I reload with the 115 gr. Quality and uniformity is good. I can't tell them apart from factory loads like American eagle.
|
August 3, 2012, 12:19 PM | #4 |
Member
Join Date: August 1, 2012
Location: Florida
Posts: 98
|
You can find cast bullets from a company called friends wood bullet on gun broker 1000 125 grain round nose for about 60 dollars they shoot great out of my glock 19 and 26.
|
August 3, 2012, 12:20 PM | #5 |
Senior Member
Join Date: June 29, 2012
Location: Phoenix
Posts: 188
|
I use a 125 grain lead round nose from Crown Bullets in Interlachen Florida. At $31.00 for 500 I load 100 rounds for about $10.80 per hundred. They ship in a USPS Flat Rate Box for $15.00 so I get 2000 at a time. They work fine through my Glock and 1911.
|
August 3, 2012, 12:27 PM | #6 |
Senior Member
Join Date: October 17, 2007
Location: Cowtown of course!
Posts: 1,747
|
For bulk FMJ's at a decent price try looking here:
http://wideners.com/itemview.cfm?dir=278|281|1082|1145 http://www.rozedist.com/mm5/merchant...y_Code=ZBJ-9MM
__________________
NRA Chief Range Safety Officer, Home Firearms Safety, Pistol and Rifle Instructor “Today, we need a nation of Minutemen, citizens who are not only prepared to take arms, but citizens who regard the preservation of freedom as the basic purpose of their daily life......” President John F. Kennedy |
August 3, 2012, 02:46 PM | #7 |
Senior Member
Join Date: June 16, 2011
Location: Ohio
Posts: 1,497
|
Thanks for the info all, guess I'll pick one or 2 to start and see how it goes
__________________
"The best diplomat I know is a fully charged phaser bank" - Montgomery Scott |
August 3, 2012, 02:54 PM | #8 |
Senior Member
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,930
|
The Berry's 124 grain HP has worked well for me. I load them with TiteGroup most of the time. In a pinch I will use Bull's Eye. All of my 9mm pistols shoot well with them.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you. |
August 3, 2012, 04:01 PM | #9 |
Senior Member
Join Date: June 6, 1999
Location: El Paso, TX
Posts: 1,021
|
Shooting lead has very little to do with the brand or model of the gun and very much to do with the individual barrel that is in your gun. In a perfect world your barrel would measure .355 from groove to groove and you would be able to shoot .356 bullets down it without problem. In reality barrels aren't always exactly what they should be and so sometimes problems arise from it. If the barrel is a little smaller like .354, you are still good to go with lead bullets. But when the barrel starts getting larger than spec, like .357+ those lead bullets can have all sorts of problems beyond just leading your barrel. Awful accuracy and keyholing can be very common.
The easy way to test this is to buy some lead bullets and shoot them. Simple enough right? If they are accurate then there probably isn't a problem. Odds are good they will leaving leading in your barrel anyway but most cast bullets are too hard for the velocities people shoot them at. Not a sizing problem at all. The more cautious way will be to slug your barrel and will require a soft piece of lead bigger than your barrel (like a big fishing weight), a wooden dowel, a hammer and some way to accurately measure the lead weight after you force it down your barrel. Here is a good webpage explaining more if you are interested. http://7.62x54r.net/MosinID/MosinSlug.htm
__________________
New gun, same ol' shot. |
August 3, 2012, 04:50 PM | #10 |
Senior Member
Join Date: March 28, 2009
Location: Kansas
Posts: 348
|
Another satisfied Berry's user on the 124 grain with Titegroup. I pick mine up directly from Powder Valley.
|
August 3, 2012, 07:22 PM | #11 |
Senior Member
Join Date: May 29, 2011
Location: Fort Worth
Posts: 500
|
Look at Missouri Bullet Co. for lead and Precision Delta for jacketed. Both good bullets and I don't believe you will beat their prices anywhere.
__________________
Education teaches you the rules, experience teaches you the exceptions (Plagiarized from Claude Clay) |
August 3, 2012, 07:48 PM | #12 |
Senior Member
Join Date: December 24, 2008
Location: Loveland, CO
Posts: 1,476
|
If you are willing to increase your order quantity, I just can't find any other bullets that will be competitive with the Montana Gold 115 gr. FMJ delivered to your door for $0.07625 each.
Yes I can buy lead for slightly less, but for the small increase in cost I would prefer to use jacketed. And I can never find plated for even close to that price. YMMV |
August 3, 2012, 08:31 PM | #13 |
Senior Member
Join Date: July 6, 2010
Location: OTS
Posts: 1,035
|
Berry's +1
__________________
Experience is what you get when you don’t get what you want. |
August 4, 2012, 01:27 AM | #14 |
Senior Member
Join Date: March 28, 2007
Location: SOCAL
Posts: 359
|
www.montanagoldbullet.com
Case of 3750 9mm, 124gr HP are $325 delivered. I think they are about the same cost as Berry's plated but you get a full jacketed bullet. Most IDPA, USPSA and, IPSC competitors shoot Montana Gold bullets. Great bullets!
__________________
I am the Christian Conservative that CNN warned you about!! “Socialism is the philosophy of failure, the creed of ignorance and the gospel of envy.” Winston Churchill |
August 4, 2012, 06:34 AM | #15 |
Senior Member
Join Date: June 2, 2011
Posts: 177
|
Also, consider this guy:
http://www.bulletheads.com/index.html |
August 4, 2012, 10:17 AM | #16 |
Senior Member
Join Date: December 17, 2005
Location: Swamp dweller
Posts: 6,187
|
My reloads in my Beretta 92 has been issue less. 115 grain lead,125 grain lead no problem with Titegroup powder. In bulk plated or fmj's will cost around 1 1/2 to 2 cents more than lead bullets.
__________________
NRA Life Member, NRA Chief Range Safety Officer, NRA Certified Pistol Instructor,, USPSA & Steel Challange NROI Range Officer, ICORE Range Officer, ,MAG 40 Graduate As you are, I once was, As I am, You will be. |
August 4, 2012, 12:44 PM | #17 |
Senior Member
Join Date: December 14, 2004
Location: Northern Indiana
Posts: 6,117
|
I use Penn’s 125 (dia .356) with a mid load of W231. 60$ for 1000.
I don’t have a 92 but my Beretta Cougar and Storm carbine like it a lot. With the Carbine I have had groups under 4 inches at 100 but the drop is significant. http://www.pennbullets.com/9mm/9mm-caliber.html |
|
|