The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Hunt

View Poll Results: Which Barnes TTSX for elk
180 grain Barnes TTSX 1 5.56%
168 grain Barnes TTSX 17 94.44%
Voters: 18. You may not vote on this poll

Reply
 
Thread Tools Search this Thread
Old April 23, 2014, 07:22 PM   #1
Smith and Wesson
Member
 
Join Date: March 29, 2014
Location: Texas
Posts: 55
Barnes TTSX weight

I'm looking for a 30-06 load for elk and other such ungulates. I've decided on the Barnes TTSX bullet but can't decide on the weight. I'm either going to use either the 168 grain load at 2800 fps, or the 180 grain load at 2700 fps, but I am looking for insight on which one to use. I've heard that the 168 grain TTSX's penetrate as good as 180s of another design because the Barnes retain 100-99% of their weight. So is a 168 grain TTSX as good as an 180 grain TTSX?
Smith and Wesson is offline  
Old April 23, 2014, 07:37 PM   #2
Longshot4
Senior Member
 
Join Date: February 22, 2014
Posts: 868
If I were going for Elk with a 06 I would keep it under 250 Yds. With at least 180gr. Barns for a clean kill. I believe the preferred Energy is 2000 ft.lb.
Longshot4 is offline  
Old April 23, 2014, 08:17 PM   #3
Brian Pfleuger
Moderator Emeritus
 
Join Date: June 25, 2008
Location: Austin, CO
Posts: 19,578
The whole idea of monolithic bullets is light and fast.

You generally want to step down at least one full weight class compared to traditional bullets.

The faster they go, the better they work. If you don't expect long shots (like 400+ yards long), I'd go with the lightest one they make for the caliber.
__________________
Nobody plans to screw up their lives...
...they just don't plan not to.
-Andy Stanley
Brian Pfleuger is offline  
Old April 23, 2014, 08:19 PM   #4
Ruger480
Senior Member
 
Join Date: February 23, 2013
Location: Central Iowa
Posts: 720
A buddy if mine who used to guide for elk in MT (and is taking me next year!) told me to use 180gr Nosler partitions in my '06.
Ruger480 is offline  
Old April 23, 2014, 08:39 PM   #5
Smith and Wesson
Member
 
Join Date: March 29, 2014
Location: Texas
Posts: 55
On another note, what do you think that the minimum velocity needed to initiate proper expansion on the previously mentioned animals is?
Smith and Wesson is offline  
Old April 23, 2014, 10:30 PM   #6
old roper
Senior Member
 
Join Date: June 11, 2007
Posts: 2,155
Barnes rec .030" to .070" off the lands for their bullets be good idea to work up hunting load see how they shoot first before deciding.

On bull elk tag I use 180gr Partition in my 30-06.
__________________
Semper Fi
Vietnam 1965
VFW Life member
NRA Life Member
old roper is offline  
Old April 23, 2014, 11:52 PM   #7
Smith and Wesson
Member
 
Join Date: March 29, 2014
Location: Texas
Posts: 55
To clarify my lost post, I meant what is the minimum velocity needed for a Barnes TTSX to expand when it hits an elk and the like.
Smith and Wesson is offline  
Old April 24, 2014, 04:45 AM   #8
hooligan1
Senior Member
 
Join Date: July 18, 2010
Location: Independence Missouri
Posts: 4,582
S&W,all that info is on the Barnes website, and also you can "talk to a tech".
If you push that 168 fast enough it should be a decent bullet out to 250.
Nosler makes the E-tip, which is a copper bullet, I currently use the 150 and it shoots well in my new 700, but I havent taken game with that bullet.

I'd test several types and weights if it were me, no one wants to goof a killer hunt up by poor bullet selection and poor shot placement.

Like Brian said, with Barnes bullets, speed is everything.
__________________
Keep your Axe sharp and your powder dry.
hooligan1 is offline  
Old April 24, 2014, 06:52 AM   #9
cordesr1
Member
 
Join Date: March 3, 2011
Location: Rockford, Michigan
Posts: 52
From my experience with triple shocks I would have no hesitation shooting a 150 at an elk. I have shot a ton of mule deer with an 06' with 150's and have seen just as many taken with a 25-06 shooting 115's. All results have been the same. Chest cavity looks like raspberry jam. No organ definition. cant get much "deader?" than that!

Im looking for Moose this year and only jumping up to the 165.
cordesr1 is offline  
Old April 24, 2014, 09:14 AM   #10
myfriendis410
Senior Member
 
Join Date: March 30, 2011
Location: Lompoc California
Posts: 274
You have to go with what your rifle likes. It may prefer a 168 gr. over a 180, or vice versa. Both would be good choices on elk, but I prefer the lighter loading. Like Brian said: light and fast. The reasoning behind light in a solid copper bullet is that it does indeed retain 100 percent of it's weight. That 180 gr. Partition, at 70% ends up at 125 gr. or so. The Barnes remains at 168 gr. when it's done it's job.

I prefer the Barnes over the E-tip simply because it expands more readily, being ductile copper instead of gilding metal and because the Barnes can be run WAY fast. You simply can't achieve similar velocities with the E-tip.

I've shot elk out of my .300 win mag using the 168 gr. Barnes and I'll never use anything else.
myfriendis410 is offline  
Old April 24, 2014, 04:35 PM   #11
old roper
Senior Member
 
Join Date: June 11, 2007
Posts: 2,155
One problem with Barnes is getting Min/Max velocity their site doesn't post that anymore.

Nosler posting E-Tip same a Hornady with their GMX.

I shot both Barnes and E-Tips and never recovered bullet. One of my cow elk rifles I use 150gr E-Tip.

I build 300WSM with Kreiger 5r barrel 1/11.25 twist.

165gr AB------ 65gr/R17 @ 3128fps
168gr E-Tip----65gr/R17 @ 3170fps
168g TTSX-----65gr/R17 @ 3177fps
__________________
Semper Fi
Vietnam 1965
VFW Life member
NRA Life Member
old roper is offline  
Old April 24, 2014, 04:46 PM   #12
Brian Pfleuger
Moderator Emeritus
 
Join Date: June 25, 2008
Location: Austin, CO
Posts: 19,578
Barnes has no practical maximum speed limit. 1,800 is considered the minimum for reliable expansion.
Brian Pfleuger is offline  
Old April 24, 2014, 07:50 PM   #13
old roper
Senior Member
 
Join Date: June 11, 2007
Posts: 2,155
It's not to hard to figure out velocity for Barnes bullet since 30cal 168gr TTSX
bullet used 308 is same bullet used 30-378Wby in their manual.

Nosler Min is 1800fps and no max for E-Tip and Hornady GMX min is 2000fps and max is 3400fps.
__________________
Semper Fi
Vietnam 1965
VFW Life member
NRA Life Member
old roper is offline  
Old April 24, 2014, 10:50 PM   #14
taylorce1
Senior Member
 
Join Date: November 18, 2005
Location: On the Santa Fe Trail
Posts: 8,210
I'd go even lighter down to a 150 grain bullet for elk out of the 06, be it a Barnes TTSX or Nosler Partitions. Accubond and other bonded core bullets I'd use at least 165 grain bullets. I'd use any standard cup and core bullet in 180 grains on any elk without hesitation out of an 06. If you hit them right elk aren't terribly difficult to kill, hit them in the wrong place and they can go for miles very quickly.
__________________
NRA Life Member
taylorce1 is offline  
Old April 25, 2014, 04:10 PM   #15
jmr40
Senior Member
 
Join Date: June 15, 2008
Location: Georgia
Posts: 10,792
At 30-06 speeds you need no heavier than 150's. The 180's are far too heavy in a copper bullets and the 165/168's should be reserved for 300 magnums.

With conventional jacketed lead bullets 180's would be my choice, but you cannot shoot copper bullets fast enough in a 30-06 to get reliable expansion except at very close range. Bullet speed at impact should be 2000-2200 fps for reliable expansion of the TTSX's. The 150 gr copper bullets will easily out penetrate 180 gr lead bullet and still be moving fast enough out to 300-400 yards to give good expansion. The heavier bullets just aren't needed in copper.
jmr40 is offline  
Old April 25, 2014, 10:02 PM   #16
Bultaco
Senior Member
 
Join Date: September 25, 2013
Location: Western Co.
Posts: 156
I would agree that when using the solid copper bullets you can get better results with more speed. The sectional density becomes much less of an issue when the bullet doesn't lose weight. You do have to be sure to use the loading data specifically for those bullets. They create pressure differently partially due to the greater resistance to engraving by the rifling. I have watched a guy drop a Barnes bullet over his normal Sierra boat tail load & have to open the bolt with a rubber hammer. The most important thing is to spend a lot of practice ammo from field positions. Good bullets in a bad location are still bad.
Bultaco is offline  
Old April 26, 2014, 07:13 AM   #17
old roper
Senior Member
 
Join Date: June 11, 2007
Posts: 2,155
Velocity is nice but you got to get it. The Barnes 168gr TTSX is 1.418" long so your going to have that bullet base in the case body. How much depends on how your rifle is throated and how far off the lands you get best accuracy. That Nolser 168gr E-Tip I shot in 300WSM was 1.400" long.

The Barnes 150gr is 1.300" long and 150gr E-Tip is 1.293" long. A 150gr Partition is 1.100",165gr Partition 1.173" and 180gr Partition 1.180".
__________________
Semper Fi
Vietnam 1965
VFW Life member
NRA Life Member
old roper is offline  
Old May 17, 2014, 08:22 PM   #18
Unlicensed Dremel
Junior member
 
Join Date: February 13, 2014
Location: Flathead Valley, MT
Posts: 2,187
Quote:
The whole idea of monolithic bullets is light and fast.

You generally want to step down at least one full weight class compared to traditional bullet
Yup. 168s
Unlicensed Dremel is offline  
Old May 19, 2014, 09:21 PM   #19
reynolds357
Senior Member
 
Join Date: December 10, 2012
Posts: 6,161
168 would be the absolute heaviest I would use.
The X will expand pretty well at low velocities. Even if it does not, it still gives an exit hole and a blood trail.
reynolds357 is offline  
Old May 20, 2014, 10:21 AM   #20
AllenJ
Senior Member
 
Join Date: December 11, 2009
Location: Northern California
Posts: 1,766
I agree with Reyonlds357, the 168 is the heaviest I would use and I would seriously consider the 150 TTSX.
AllenJ is offline  
Old May 20, 2014, 02:35 PM   #21
nc-oldfart
Senior Member
 
Join Date: April 2, 2014
Posts: 155
I to would use the 150gr . I have not killed with a 30 cal using a barnes but have with a 140gr tsx in a 7mm at 2850fps shoot at 210 yards and found the bullet after 51" of meat, spine ,ribs and shoulder damage. amassing amount of damage.
nc-oldfart is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:04 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.10387 seconds with 11 queries