The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools Search this Thread
Old October 27, 2015, 07:56 PM   #7051
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
It's a S&W 38 special. Serial number 225854.
Does it hold 5 or 6 rounds? And can I assume you took the serial number from the underside of the grip frame? And there are no letter prefixes?

Quote:
Airweight Bodyguard J-Frame in .38 Special which has a pinned barrel. I believe it may be a Model 38. The serial number is J883075.
J883xxx = 1981.
The model number should be stamped on the frame in the cutout just forward of the cylinder and visible when the cylinder is swung out.
I'm pretty sure from my time over on the S&W forums that S&W does not use a copper undercoat. But...

Jim

Last edited by laytonj1; October 27, 2015 at 08:02 PM.
laytonj1 is offline  
Old October 27, 2015, 11:05 PM   #7052
Doc Intrepid
Senior Member
 
Join Date: May 22, 2009
Location: Washington State
Posts: 1,037
Thanks Jim....

Quote:
Originally Posted by laytonj1
"J883xxx = 1981.

The model number should be stamped on the frame in the cutout just forward of the cylinder and visible when the cylinder is swung out.

I'm pretty sure from my time over on the S&W forums that S&W does not use a copper undercoat. But..."
Thanks Jim,

The markings stamped on the frame forward of the cylinder are "MOD-38" (which was my clue!), however there was no "dash X" or other specification so was not sure - apparently the model designations changed a bit between 1955 and later years.

There are four (4) separate stamp marks on the frame beneath the left grip which are:
  • a large "N";
  • a C24 just above the "N" but in smaller font;
  • an F17; and
  • the number 55787.

Beneath the right grip is the number "4781". I was not sure what all these designations might mean.

In terms of being copper plated before being nickel plated, the guy who described this was an older gunsmith who indicated that nickel doesn't plate well on top of aluminum, so they plated a thin layer of copper to the aluminum first so the nickel plating would adhere properly. Who knows?

If this is a 1981 serial number it's a bit newer than I expected, but still in my ballpark.

I appreciate your time. Thanks again,

Doc
__________________
Treat everyone you meet with dignity and respect....but have a plan to kill them just in case.
Doc Intrepid is offline  
Old October 28, 2015, 04:00 PM   #7053
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
There are four (4) separate stamp marks on the frame beneath the left grip which are:
a large "N";
a C24 just above the "N" but in smaller font;
an F17; and
the number 55787.
The "N" stamps are for Nickel. The others are assembly and inspector stamps.
J frame serial numbers for 1981 ran from J760001 to J915400.
1983 was around the period that S&W stopped pinning the barrels.

Jim
laytonj1 is offline  
Old October 28, 2015, 04:08 PM   #7054
Doc Intrepid
Senior Member
 
Join Date: May 22, 2009
Location: Washington State
Posts: 1,037
Many thanks, again, for this information.

As a fan of older S&W revolvers in excellent condition, I'm glad I found one with the barrel pinned, and I appreciate your historical comments.

Doc
__________________
Treat everyone you meet with dignity and respect....but have a plan to kill them just in case.
Doc Intrepid is offline  
Old October 29, 2015, 01:05 PM   #7055
walnut1704
Senior Member
 
Join Date: October 28, 2009
Posts: 156
How about the date on a Model 657, which is a 6" stainless in .41 Magnum, serial number CAA16XX?

Thanks......
walnut1704 is offline  
Old October 29, 2015, 08:13 PM   #7056
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
serial number CAA16XX?
1995.

Jim
laytonj1 is offline  
Old November 2, 2015, 10:10 AM   #7057
Kywildcat1974
Junior Member
 
Join Date: October 25, 2015
Posts: 2
Forgive me everyone, I have no idea how this works

I'm just needing info on a gun
Kywildcat1974 is offline  
Old November 3, 2015, 11:45 PM   #7058
HALL,AUSTIN
Senior Member
 
Join Date: June 23, 2011
Location: asheville north carolina
Posts: 556
28-2
n5237xx
HALL,AUSTIN is offline  
Old November 6, 2015, 04:20 PM   #7059
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
It's a S&W 38 special. Serial number 225854.
I'm just needing info on a gun
If it holds 5 rounds then it's likely a model 36 and SN. 225854 would date it to about 1960/61.
If it holds 6 rounds then it's likely a .38 Military & Police and the sn. 225854 would date it to about 1914/15.

Quote:
28-2
n5237xx
The N5xxxxx range ran from 1978 to 1980.

Jim
laytonj1 is offline  
Old November 9, 2015, 10:30 AM   #7060
pluggerlewis
Junior Member
 
Join Date: November 8, 2015
Posts: 2
38 Special Airweight

I have inherited a Mod. 37 5 shot 38 special airweight. I am trying to find out some info on. the S/N on the bottom of the handle frame is 535209. It has another # that is on the side of the handle frame that matches the # by the cylinder (85323). Any help will be greatly appreciated.
pluggerlewis is offline  
Old November 9, 2015, 06:01 PM   #7061
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
the S/N on the bottom of the handle frame is 535209
Around 1966/67. The other numbers are assembly numbers.
The model 37 is the aluminum frame version of the model 36.

Jim
laytonj1 is offline  
Old November 9, 2015, 08:59 PM   #7062
pluggerlewis
Junior Member
 
Join Date: November 8, 2015
Posts: 2
Thanks Jim. One last question, is this what they call the "Chiefs special"?
pluggerlewis is offline  
Old November 10, 2015, 08:38 PM   #7063
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
is this what they call the "Chiefs special"
Yes.
Prior to S&W coming up with the model number system around 1958, all their models went by names. Yours would be the Chiefs Special Airweight.

Jim
laytonj1 is offline  
Old November 15, 2015, 12:19 AM   #7064
gunlover22
Junior Member
 
Join Date: November 14, 2015
Posts: 1
Looking for manufacturer date

Hi, I recently inherited a S and W 38 special from my grandfather. The serial # is S 9343xx. Any idea of the date manufactured? Thanks Ron
gunlover22 is offline  
Old November 15, 2015, 05:37 PM   #7065
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
The serial # is S 9343xx.
It's a .38 Military & Police. Serial numbers ran from S811120 in 1945 to S999999 in 1948.
When S&W began the model numbering system ~ 1957 the 38 M&P became the model 10.

Jim
laytonj1 is offline  
Old November 17, 2015, 02:20 PM   #7066
Wharfrat197601
Junior member
 
Join Date: October 23, 2015
Posts: 7

BAA14_ _.

Main forum said it was 1988.
Wharfrat197601 is offline  
Old November 17, 2015, 05:12 PM   #7067
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
BAA14_ _.
1988 would be correct.

Jim
laytonj1 is offline  
Old November 17, 2015, 08:50 PM   #7068
tfn41
Junior Member
 
Join Date: September 13, 2015
Posts: 4
CDC9xxx

It's got 527 on the crane, but that's not the model number. What does that mean?

Thanks in advance...
tfn41 is offline  
Old November 17, 2015, 09:32 PM   #7069
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
CDC9xxx
It's got 527 on the crane,
1999.
That number would be an assembly number.

Jim
laytonj1 is offline  
Old November 25, 2015, 06:31 PM   #7070
Pooch28
Junior Member
 
Join Date: November 24, 2015
Posts: 1
Just bought a second hand model 60 J Frame
Serial #ANR5*** could someone please give me an approximate manufacture date
Pooch28 is offline  
Old November 26, 2015, 01:39 PM   #7071
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Serial #ANR5***
1986/87.

Jim
laytonj1 is offline  
Old December 4, 2015, 12:31 PM   #7072
KenHo
Junior Member
 
Join Date: August 18, 2014
Posts: 2
Request for date of manuf

Hello all - my wife has a S&W, mod 60, 5 shot revolver (SS?) with serial number located on butt stock of AVW31XX

Can anyone provide a year of mauf?

Thank you for any help,

Ken H>
KenHo is offline  
Old December 4, 2015, 08:02 PM   #7073
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
serial number located on butt stock of AVW31XX
1987.
And yes, it's stainless steel.

Jim
laytonj1 is offline  
Old December 4, 2015, 09:48 PM   #7074
KenHo
Junior Member
 
Join Date: August 18, 2014
Posts: 2
Thank you - that's about the date I was thinking it might be.

Ken H
KenHo is offline  
Old December 11, 2015, 01:55 PM   #7075
wiesjon
Junior Member
 
Join Date: July 18, 2008
Posts: 2
Model 586 serial no. 32141 date of manufacture?
wiesjon is offline  
Reply

Tags
s&w 686

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:15 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.65983 seconds with 9 queries