The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools Search this Thread
Old December 20, 2014, 09:36 PM   #6751
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
The serial number on the base of the frame is 6K137xx.
The serial number on the base of the frame is R1058xx
6K137xx = 1974.
R1058xx = SN's ran from R100000 in 1974 to R190000 in 1977 so must likely 1974 also.
The other numbers you see are assembly and inspector numbers. There have been time periods when S&W also stamped the SN on the frame in the yoke area but (with very few exceptions) the base of the grip is the one consistent location.

Jim
laytonj1 is offline  
Old December 21, 2014, 12:30 PM   #6752
Doc Intrepid
Senior Member
 
Join Date: May 22, 2009
Location: Washington State
Posts: 1,037
Jim,

Thanks very much. I am grateful for your time and response.

It appears I have a couple 40 year old S&W revolvers, and I'm real pleased to discover this. I appreciate your information.

Doc
__________________
Treat everyone you meet with dignity and respect....but have a plan to kill them just in case.
Doc Intrepid is offline  
Old December 21, 2014, 10:14 PM   #6753
Obj wan
Junior Member
 
Join Date: December 19, 2014
Posts: 1
Model 36

J205xxx

Got this model 36 for my wife about 13 years ago.
Obj wan is offline  
Old December 22, 2014, 02:22 PM   #6754
rdping
Junior Member
 
Join Date: February 16, 2012
Posts: 3
[ATTACH]image.jpg[/ATTACH]Quote:
38 S&W Special; ser#102*; model 6029; 4" barrel
No such model number from S&W. Sounds like an assembly number.
See four post above yours for location of serial number. If your gun was made after 1957 the pics above also show the location of the model number, it will start with M or MOD.

Jim


This is a old M&P 1st edition...pre 1900 model

Last edited by rdping; December 22, 2014 at 02:41 PM.
rdping is offline  
Old December 22, 2014, 06:00 PM   #6755
DWG1861
Junior Member
 
Join Date: December 21, 2014
Posts: 2
Have an old "Model 10"???

I bought a S&W revolver that in all respects looks like a model 10, 5 inch bbl; however in the yoke there is no model number like my other 10. Instead there is a stylized number 1 with a smaller number 1 in a circle slightly above and to the left. In the bottom part of the yoke is the number 4. Shoots well, is in great shape, just curious as to what "model" it may be. The serial # on the butt is C 428xxx. Any ideas?
DWG1861 is offline  
Old December 22, 2014, 08:43 PM   #6756
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Model 36
J205xxx
SN's ran from J100000 in 1973 to J250000 in 1974. So, most likely 1974.

Quote:
This is a old M&P 1st edition...pre 1900 model
Your right. It's a .38 M&P 1st Model. Pictures help a lot. Serial number dates it to 1st year of production. SN's ran from 1 in 1899 to 20975 in 1902.

Quote:
The serial # on the butt is C 428xxx.
It's a 38 Military & Police. They became the model 10 when S&W began stamping model numbers ~ 1957.
Yours dates to 1949.

Jim
laytonj1 is offline  
Old December 22, 2014, 09:50 PM   #6757
DWG1861
Junior Member
 
Join Date: December 21, 2014
Posts: 2
To laytonj1

Thanks for your help; this piece is in excellent shape for its age (better than me)!
DWG1861 is offline  
Old December 23, 2014, 12:40 PM   #6758
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Quote:
The serial # on the butt is C 428xxx.

It's a 38 Military & Police. They became the model 10 when S&W began stamping model numbers ~ 1957.
Yours dates to 1949.
Sorry DWG1861, I typo'd the date. It's 1959. SN's ran from C402924 in 1957 to C429740 in 1959.

Jim
laytonj1 is offline  
Old December 27, 2014, 01:22 PM   #6759
Mojave
Member
 
Join Date: June 11, 2011
Posts: 68
I recently scored a beauty: Model 57 no dash 4" in nickel, fired very little. Serial number is N878xxx. Recessed cylinder but the barrel isn't pinned, so I'd guess early 80's before the recessed cylinder was phased out.
Mojave is offline  
Old December 27, 2014, 05:44 PM   #6760
skedaddle23
Junior Member
 
Join Date: December 27, 2014
Posts: 1
I just got a 629-3; 8 3/8"; Classic with full lug barrel, pre-lock. It is in excellent shape can someone look up for me the production time frame. The number inside the crane is BKA5xxx.

Thanks for making this resource available.
skedaddle23 is offline  
Old December 27, 2014, 09:28 PM   #6761
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Serial number is N878xxx
The N8xxxxx range ran from 1980 to 1983.


Quote:
BKA5xxx
~1991.

Jim
laytonj1 is offline  
Old December 27, 2014, 09:59 PM   #6762
Mojave
Member
 
Join Date: June 11, 2011
Posts: 68
Thanks Jim!
Mojave is offline  
Old December 29, 2014, 11:45 AM   #6763
iompaul4555
Junior Member
 
Join Date: December 23, 2014
Posts: 1
Hello from a real newbie

I am in the UK, and have been left an S W Revolver by my brother. It is old, I think from WW2. I was told a Navy Model as it has a Lanyard on it. It is .32.
Model Number is, I think, 780450 and on the frame, 27597.
Yes, I know, I should invest in a S&W Book, but due to firearms restrictions here, I cannot see me owning another one!

Anyone care to help please?
iompaul4555 is offline  
Old December 30, 2014, 01:51 PM   #6764
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Model Number is, I think, 780450 and on the frame, 27597.
See pic for location of serial number. If it's a pre 1957 then there will be no model number on it. An older gun may also have the serial number stamped on the underside of the barrel and the back of the cylinder. One or both of the numbers you gave are assembly numbers. In addition, I need to know the exact wording of the caliber stamped on the side of the barrel. And, of course, a picture always helps.

Jim

laytonj1 is offline  
Old January 2, 2015, 02:33 PM   #6765
GMTHOMAS44
Junior Member
 
Join Date: December 31, 2014
Posts: 2
2 k frames

Hello All,
Need some info and advice on 2 k frames I got from my grandfather.
1. .38 spl K364270, pinned, not recessed maybe 97-98%
2. .22 K28293, pinned, recessed, maybe 95-96%
I think he bought them in the 50's or 60's. What year are they and is either one worth the $50 to get a letter of authentication from S&W? I don't plan on selling them but I do plan on dieing sometime and would like to leave my wife some info if they are worth anything special.
.38 has wide/serrated hammer and wide grooved trigger unknown grips
.22 has narrow trigger & hammer, Herret grips both have 6" bbl. & I have original grips.
Thanks for any info/help GTP1000541.JPG

P1000542.JPG
GMTHOMAS44 is offline  
Old January 2, 2015, 04:25 PM   #6766
Dead-Nuts-Zero
Senior Member
 
Join Date: August 26, 2004
Posts: 577
SN Search

Picked up a nice used k-17 (I think) of maybe K-22???
Butt stamp under grip is K 2908XX
Crane area has two numbers "N" over 80841 and another 80841 with other various scribes & production markings.

Six Shot 6' Blued revolver with typical large S&W factory wood grips.

Would be very grateful if someone could help me out with identifying model & DOB.

Unable to provide photo at this time but will get help with photo if needed.

Many thanks to all the dedicated posters who help us ID these great S&W arms.
__________________
.
.
BANG------------ >>> !
Dead-Nuts-Zero is offline  
Old January 2, 2015, 07:17 PM   #6767
finloq
Member
 
Join Date: October 2, 2010
Posts: 73
Model 1905 4th Change (32-20)

#96441
finloq is offline  
Old January 2, 2015, 07:49 PM   #6768
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
1. .38 spl K364270, pinned, not recessed maybe 97-98%
2. .22 K28293, pinned, recessed, maybe 95-96%
K364270 = 1959. It would be a model 14.
K28293 = 1948. It would be a K-22.
The letter would tell you when shipped and to whom it was shipped. Value on these continue to rise but I would guess $700 to $900 range.
Recessed chambers were only on 22's and magnums.
Quote:
Butt stamp under grip is K 2908XX
K2908xx = 1957. It would be a K-22. Later that year when S&W started assigning model numbers it would become the model 17.

Quote:
Model 1905 4th Change (32-20)

#96441
Serial numbers ran from 65701 in 1915 to 144684 in 1940.
The book does not break it down any further but does mention SN 81287 was ~1921.

Jim

Last edited by laytonj1; January 2, 2015 at 07:56 PM.
laytonj1 is offline  
Old January 2, 2015, 08:17 PM   #6769
ghenry1114
Junior Member
 
Join Date: January 2, 2015
Posts: 4
s&w 10-6

Looking at a model 10-6 it has a custom barrel, bo-mar sights, 99% blue ser# 71847 from the yoke. Can anyone tell me about how old it is or the value? thanks!
ghenry1114 is offline  
Old January 2, 2015, 08:19 PM   #6770
finloq
Member
 
Join Date: October 2, 2010
Posts: 73
Model 1905 4th Change (32-20)





#96441


Serial numbers ran from 65701 in 1915 to 144684 in 1940.


The book does not break it down any further but does mention SN 81287 was ~1921.


Thanks Jim. I would have figured 1922-1924, but a Veteran over in the S&W forum stated that he believed it was 1921. I will stick with: early 20's.
finloq is offline  
Old January 2, 2015, 08:25 PM   #6771
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Looking at a model 10-6 it has a custom barrel, bo-mar sights, 99% blue ser# 71847 from the yoke
Five post up from yours is a picture with the serial number location. The number you gave is an assembly number.

Jim
laytonj1 is offline  
Old January 2, 2015, 10:05 PM   #6772
GMTHOMAS44
Junior Member
 
Join Date: December 31, 2014
Posts: 2
Thanks

laytonj1,
Thanks for the info I appreciate it. the .38 has Mod-14 under the chamber and the set of original grips for the .22 have the serial number stamped on them. My grandfather was an -06 shooter (Army Guard) in the '27-'28 camp perry matches, and made enough on"side bets" (illegal) to buy an engagement ring for my Grandmother that he couldn't afford when they were married several years before. GT
GMTHOMAS44 is offline  
Old January 4, 2015, 01:25 AM   #6773
Dead-Nuts-Zero
Senior Member
 
Join Date: August 26, 2004
Posts: 577
Thank You laytonj1

laytonj1

Many thanks for the S&W info!
__________________
.
.
BANG------------ >>> !
Dead-Nuts-Zero is offline  
Old January 8, 2015, 11:42 AM   #6774
rengewnad
Junior Member
 
Join Date: December 23, 2014
Posts: 1
Identify build date/history? - Model 10-10

new to me Model 10-10, interested in some history if you have it.

Serial Number on bottom of frame: BFE53XX

Number on Left side of frame under the grip, just above the serial number: 95249
Near this number are a stamped R in a circle, and a stamped C in a triangle. Above the stamped R there is a stamped number 224

On the right side of the frame under the grip, just above the serial number, is another stamped number, but this is a different font than the other two numbers I provided. It's just a bunch of dots, forming what appears to be: 3566 683

Any insight into the history of this gun?

Thanks!
rengewnad is offline  
Old January 8, 2015, 07:54 PM   #6775
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Serial Number on bottom of frame: BFE53XX
1990.
A book could be written on the history of the model 10 as it's been in continuous production since 1899.
It started out as the .38 Military & Police and became the model 10 when S&W started assigning model numbers in 1957.

Jim
laytonj1 is offline  
Reply

Tags
s&w 686

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:47 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.98964 seconds with 9 queries