|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
September 6, 2013, 11:46 PM | #1 |
Senior Member
Join Date: June 6, 2012
Location: Berkshire Hills
Posts: 741
|
question regarding price of .45 Colt cowboy ammo
Just curious as to what you are paying for .45 colt cowboy ammo in your area. I am just getting into trying these in my '58 Pietta. Haven't even got the cylinder yet, but should have soon. What is a decent price for the ammo?
__________________
NRA Patron Member SAF Life Member GOAL Member |
September 7, 2013, 12:19 AM | #2 |
Junior member
Join Date: October 19, 2004
Location: michigan
Posts: 578
|
hmm please before you get the cylinder go to various online companies that sell ammo.
The most commonly found ammo in the bulk 45 long colt category is well, $0.85 a round before shipping if you buy a 250 round container. Then toss in shipping, taxes, it gets screwy. the best price i have seen in person since the panic started was 30 dollar for a single 20 round box of federal semi wadcutter hollowpoints. before tax. You might think percussion caps are expensive, if it has cowboy on the box most companies add on 5-8 dollars per box. |
September 7, 2013, 04:55 AM | #3 |
Senior Member
Join Date: October 24, 2008
Location: Naples, Fl
Posts: 5,440
|
Load your own...
and cast your own bullets.
Price per round get crazy cheap.
__________________
Seek truth. Relax. Take a breath. |
September 7, 2013, 07:29 AM | #4 | |
Senior Member
Join Date: January 7, 2012
Location: Auburn, AL.
Posts: 2,332
|
Quote:
__________________
. . . Have a Colt and a smile. |
|
September 7, 2013, 08:31 AM | #5 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,190
|
Before the panic it was 35.00 per 50 round box at Wal Mart. Have no idea what it is now.
|
September 7, 2013, 08:31 AM | #6 |
Senior Member
Join Date: June 6, 2012
Location: Berkshire Hills
Posts: 741
|
Thanks guys. If I like shooting them, I will try reloading my own. Many companies will not ship ammo to my state.
__________________
NRA Patron Member SAF Life Member GOAL Member |
September 8, 2013, 11:38 AM | #7 |
Junior member
Join Date: January 1, 2007
Location: Idaho
Posts: 2,282
|
Yep, even at todays component prices It's like less than $5.00 per fifty if you cast and load your own, and you don't have to settle for whatever wally world has on hand.
|
September 8, 2013, 12:03 PM | #8 |
Senior Member
Join Date: January 29, 2005
Location: Southern California
Posts: 344
|
I cast and load my own Cowboy loads. It's not only cheaper but you are more self sufficient as well.
If I were to buy my rounds today I would go to one of the many gun shows on the weekends and buy there. The prices will be better than stores or online shipping. |
September 8, 2013, 02:50 PM | #9 |
Senior Member
Join Date: January 27, 2009
Location: Blue Ridge Plateau
Posts: 151
|
.45
About 40.00 for a box of 50 Winchester Super X Cowboy loads. That was at Cabela's last week. The only place in town that occasionally has a few boxes. Fresh 45 Colt is actually easier to find here than reloading components for the same calibre.
|
September 8, 2013, 08:08 PM | #10 |
Senior Member
Join Date: April 3, 2011
Location: to close to other houses
Posts: 1,176
|
$26.50 per 50 for LFP loaded to cowboy specs
$36.99 per 50 for basically the same load but with JHPs these are really high quality and accurate reloads I buy from a local shop owner. He gives me .08 off per round when I bring him the brass back to load up for me to boot. I cant afford to buy factory 45 colt, and I don't have anywhere to reload myself. |
September 10, 2013, 06:53 AM | #11 |
Senior Member
Join Date: September 7, 2012
Location: Crockett, Texas
Posts: 363
|
I have a 1873 Colt repro in .38/.357, and I got around the whole ammo mess by getting myself a Lee handpress and a set of dies. Load up using either your storebought bp or substitute or some of your own press cake, cast yer own bullets, and your cost will be minimal. A few good days of shooting and my modest investment had already paid itself off.
__________________
"I'm your huckleberry, it's just my game" |
September 10, 2013, 07:08 PM | #12 |
Senior Member
Join Date: February 15, 2011
Posts: 277
|
Sportsman guide has some magtech fot 32 a box, if you get them on a free shipping day that sometimes helps
|
September 18, 2013, 05:12 PM | #13 |
Junior Member
Join Date: January 27, 2013
Location: Cypress,Republic of Texas
Posts: 2
|
Even if you have to buy lead off of castboolists.com or ebay you can reload for about 10 cents per round. This doesn't count the cost of the cases.
With a mild powder load you can get a goodly number of reloads per case. cr
__________________
SASS 48747L USPSA 1314L NRA-Life |
September 19, 2013, 10:31 AM | #14 |
Senior Member
Join Date: September 25, 2012
Location: Chester Va
Posts: 360
|
$26.50 for 50 at Georgia Arms.
|
September 21, 2013, 04:44 PM | #15 |
Senior Member
Join Date: June 6, 2012
Location: Berkshire Hills
Posts: 741
|
What do you guys think about Lee reloading products? I seem to run across a lot of negative stuff. Is this snobbery or are there real problems with this brand?
__________________
NRA Patron Member SAF Life Member GOAL Member |
September 21, 2013, 05:33 PM | #16 |
Senior Member
Join Date: January 7, 2012
Location: Auburn, AL.
Posts: 2,332
|
I reload a bazillion shells with Lee. I don't have any of their molds, so can't say, but their presses and dies work very well. The breechlock system sure makes changing dies a snap too. (literally)
I do have 2 sets of Hornady New Dimension Nitride dies, but I can't say they really outshine the Lee's by much.
__________________
. . . Have a Colt and a smile. |
September 21, 2013, 05:49 PM | #17 |
Senior Member
Join Date: October 24, 2008
Location: Naples, Fl
Posts: 5,440
|
NER
Please understand that I am not a purist. I don't have a lot of experience with a wide range of equipment and so my sentiments have limited value.
I like their products. The multistage press is a good option. I converted mine to four positions (cost was about 17.00 and I did not use the progressive rod) but I would not have needed to do so. I don't typically use a factory crimp die so three positions is really all I need. I have a turret set up for each of my calibers (.357, .44 Mgnm, .45LC, .45-70 govt and .45 ACP). This reduces the time required to set up the press. I just run a coulpa rounds through to make sure the set up is still good. I have Lee molds which I like much more than the Lyman/Ideal molds I have for round balls. For bullets I use only Lee molds but that is because I just never tried higher price molds. They work fine. I have a Pacific single stage press and also used an old single stage press from another manufacturer (can't remember whose) and those presses are extremely high quality, but a single stage press just doesn't work for me. I have the Lee hardness tester which I like because it does the job for a low price. Also have the Lee ten pound production pot. This is my second one. The first Production Pot was still working fine but I figure after 35 years I deserved to spend the 57.00 on a new one. I gave the old one to a friend and he is still using it. The dies from Lee are easy to set up and give good consistent rounds.
__________________
Seek truth. Relax. Take a breath. |
September 21, 2013, 06:21 PM | #18 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,190
|
I use a lot of Lee stuff and like it. Most of my molds are Lee and I really like Lee dies. Some don't like them because of the O ring but as long as you install and remove them using the nut they will stay adjusted. If you do it using the die body they will lose adjustment but I never had one lose adjustment while I was using it.
|
September 21, 2013, 08:49 PM | #19 |
Senior Member
Join Date: June 6, 2012
Location: Berkshire Hills
Posts: 741
|
Well, I guess I will be looking at some Lee products. Thanks guys. You have put me at ease with purchasing Lee equipment.
__________________
NRA Patron Member SAF Life Member GOAL Member |
September 22, 2013, 03:26 AM | #20 |
Senior Member
Join Date: October 24, 2008
Location: Naples, Fl
Posts: 5,440
|
If that have the stuff in stock...
...Titan Reloading has good prices, good service and fairly inexpensive shipping.
__________________
Seek truth. Relax. Take a breath. |
September 22, 2013, 07:31 AM | #21 |
Senior Member
Join Date: June 6, 2012
Location: Berkshire Hills
Posts: 741
|
I will check out Titan, was looking at the Lee site last night and saw them listed as a dealer. Thanks for the info on them.
__________________
NRA Patron Member SAF Life Member GOAL Member |
September 22, 2013, 03:05 PM | #22 |
Senior Member
Join Date: October 24, 2008
Location: Naples, Fl
Posts: 5,440
|
Just remembered....
The other single stage press I had was an Echo. I bought it cheap, rehabbed it, used it, realized single stage didn't work for me and sold it.
It was a real good press. Also had a Lyman Truline Junior which I liked but the turret was for the 310 dies. I made a turret for 7/8 inch dies and then sold it. Also made a primer holder for large primers for it. Excellent press and had great fun fooling with it.
__________________
Seek truth. Relax. Take a breath. |
September 23, 2013, 08:33 PM | #23 |
Senior Member
Join Date: June 6, 2012
Location: Berkshire Hills
Posts: 741
|
Gentlemen, thanks for all the great info! I am excited to get into this new realm of reloading. I have hit a snag in a home purchase, and will be directing my time towards overcoming this problem. As soon as that is done, I will renew my pursuit of loading equipment. Hopefully this will be set straight soon. When it is, I will probably be asking a lot more questions. Thanks again for the info and direction. Also, to the member who took the time to PM me about this subject, extra thanks to you!
__________________
NRA Patron Member SAF Life Member GOAL Member |
September 24, 2013, 07:03 AM | #24 |
Senior Member
Join Date: October 24, 2008
Location: Naples, Fl
Posts: 5,440
|
NER
Best of luck with the home.
__________________
Seek truth. Relax. Take a breath. |
September 27, 2013, 07:38 PM | #25 |
Senior Member
Join Date: June 6, 2012
Location: Berkshire Hills
Posts: 741
|
Doc, thanks man. Things are looking better. The short story is, it is a question of home insurance for a home that's being renovated. I believe between the lawyer, the lending institution and the ins company, everything is set to move toward closing.
I also received the R&D conversion cylinder from Taylors. Bolt won't lock up. Contacted Taylors, they said to send the gun or the bolt in. Free of charge they will adjust the bolt. I'm new to this but I believe the bolt is unable to lock on firing due to the bolt stops in the cylinder being cut less deep than the BP cylinder bolt stops. This is causing the bolt to not lock into place upon bringing the gun to full cock. So a simple small job of grinding of the bolt cam should fix the problem.
__________________
NRA Patron Member SAF Life Member GOAL Member |
|
|