December 10, 2012, 11:57 PM | #1 |
Junior member
Join Date: May 16, 2008
Posts: 9,995
|
Steyr M95 Sporter
Well, i am about to sin...
I have been wanting to make a few sporters out of straight pull actions for a while and it seemed like there weren't any to be had in my range. THen we end up with this glut of Steyr M95s. I am thinking I should pick up a few to hold onto for the actions. Seems many of these guns have atrocious barrels and are missing things like swivels and sights. Other straight pulls are too valuable to be doing this too and are usually in better shape than I hear these are. Sometimes blasphemy is too tempting, just don't tell my friend in the C&R area. One to 30-06 for hunting One to 460 SW for a companion carbine Mostly to fit hunting "needs." One to... Well i will buy a few extra and sporter the worst ones first. The conversions won't be happening for some time, but best to get the actions while they are readily available at a good price, right? |
December 11, 2012, 01:29 AM | #2 |
Member
Join Date: August 3, 2012
Posts: 58
|
I have thought the same thing when shooting my mil surp straight pulls. Just seems like they would make a great hunting rifle. Don't rule out the Swish. There have been some K31s and K11s imported in recent months that might be in your range. My idea is to replace the stock, and add a scout scope mount at the rear sight and save the originals. It could be done in such a way that the rifle could be restored if it became valuable in the future. The problem with the steyr miight be the odd size cartridge/bullet/bore.
|
December 11, 2012, 09:43 AM | #3 |
Junior member
Join Date: May 16, 2008
Posts: 9,995
|
I would be re-barreling these. From some research online it seems these are much easier to rebarrel then the K31 or K11. I have a 308 K11. The bolt stuck bad the first few times I shot it. As such it is now relegated to Sentry duty covering the Golden rod power cord entry hole in the back of my safe.
|
December 11, 2012, 10:13 AM | #4 |
Senior Member
Join Date: August 12, 2009
Location: Athens, Georgia
Posts: 2,526
|
The M95 was originally designed around the 8x50R cartridge. Most were later chambered in the hotter 8x56R. Can it hold up to 30-06 pressures?
|
December 11, 2012, 10:33 AM | #5 |
Senior Member
Join Date: September 19, 2008
Posts: 4,678
|
Short answer: NO.
While the Swiss will, the 120-something year old Steyr won't. Also, AFAIK, the action's too short for a standard (.30-06) length cartridge. . |
December 11, 2012, 02:48 PM | #6 |
Senior Member
Join Date: May 27, 2007
Posts: 5,261
|
Converting military actions into sporter rifles is an expensive proposition. The end result usually costs more than a new, or decent used, M700/M70/M110.
Military rifles are best left in their original caliber as feed and extraction issues pop up when you change calibers. I don’t think there is anything really wrong with a 8 X 56R as a sporting cartridge, just that brass is hard to find. Bubba won’t know what it is and won’t want it. I don’t know how late the production of 1895 actions went, but most of them are WW1 or earlier and the metallurgy of the period stinks. Now if you have a 30’s vintage M1895 action, the metal is probably just fine.
__________________
If I'm not shooting, I'm reloading. |
December 11, 2012, 09:27 PM | #7 | ||
Senior Member
Join Date: July 21, 2011
Location: Idaho
Posts: 7,839
|
Quote:
Quote:
__________________
ignore my complete lack of capitalization. I still have no problem correcting your grammar. I never said half the stuff people said I did-Albert Einstein You can't believe everything you read on the internet-Benjamin Franklin |
||
December 11, 2012, 11:13 PM | #8 | |
Senior Member
Join Date: May 17, 2012
Posts: 1,085
|
Quote:
I'm looking to rebarrel one of these to glorious .50 Alaskan. Some weeks ago I was did the research for the bolt thrust calcs over on THR; you may find the info useful: Chamber Pressure in Regards to Cartridge Selection (sent money off for cheap used dies today, and will be buying a cheap 50cal blank soon ) The main thrust () of my math was that choosing a cartridge with a lower pressure than the factory is the best bet (even if caliber is going up some). In the case of the .50AK, the larger bolt thrust area is offset by a much lower pressure. These are sturdy actions, successfully chambered in 8mm Mauser, and moreso in the extremely potent 8x56R cartridge, and if you keep your pressures and bolt thrust below those, you will be safer than the unaltered configuration. (I will be testing my model with a vice and string the first few times, though ) TCB
__________________
"I don't believe that the men of the distant past were any wiser than we are today. But it does seem that their science and technology were able to accomplish much grander things." -- Alex Rosewater |
|
December 11, 2012, 11:24 PM | #9 |
Junior member
Join Date: May 16, 2008
Posts: 9,995
|
Always ruining my fun with logic.
Looks like i am limited to 30-30 and 45-70 by pressure. Could go 357 max by pressure and probably 44 super mag or whatever the 44 stretched is called. Maybe the 454 with a bit of finger crossing. All but the 30-30 are larger diameter and I know that will complicate things a bit. I would probably do at least the first on my own. To hell with it, I will just settle on more Encore barrels. |
December 11, 2012, 11:44 PM | #10 |
Senior Member
Join Date: September 13, 2005
Posts: 4,700
|
Doesn't sound like a great idea to me, when were the last M95s manufactured-in the 1920s?
|
December 12, 2012, 12:26 AM | #11 |
Senior Member
Join Date: January 19, 2007
Posts: 2,663
|
.444 Marlin?
|
December 12, 2012, 12:31 AM | #12 |
Senior Member
Join Date: July 26, 2005
Location: Los Angeles
Posts: 351
|
It's an interesting action, and would be a most cool, idiosyncratic sporter.
I've had one of them for years, and found it punishing to shoot in 8x56mmR, so I think any large caliber is out, but what about a 7mm Mauser conversion? In any event, it would be a labor of love. |
December 13, 2012, 01:33 AM | #13 |
Junior member
Join Date: May 16, 2008
Posts: 9,995
|
How about 357 max conversion. That might work.
|
December 13, 2012, 02:37 AM | #14 |
Senior Member
Join Date: September 7, 2010
Location: Virginia
Posts: 333
|
I don't have my books handy but how about 348 win?
would make a hell of a brush gun
__________________
Superman, you are a mean drunk |
December 13, 2012, 11:07 PM | #15 |
Junior member
Join Date: May 16, 2008
Posts: 9,995
|
348 win looks good according to SAAMi, but I prefer readily available cartridges. 357 max obviously isn't readily available, but the compatible cartridges are available in any gun shop or walmart.
|
|
|