May 31, 2012, 12:54 PM | #1 |
Junior Member
Join Date: May 31, 2012
Location: Eastern PA
Posts: 1
|
Arisaka 99 bolt stuck
I recently picked up another Arisaka 99 at an estate auction. Got it cheap because no one could get the safety to work/ didnt know squat about the rifle. After closer inspection, I now see why. It looks like the plunger has rotated 90* to the left looking at the rear of the gun. The little notch that should ride through the passageway at the 6 o'clock position on the gun is actually at the 9 o'clock position. This is preventing me from disassembling the upper portion of the gun. I need to somehow get it realigned, but proving impossible. The little notch will not travel past the left side of the barrel housing ,beneath the bolt release tab. Suggestions?
|
May 31, 2012, 01:00 PM | #2 |
Senior Member
Join Date: June 16, 2011
Location: Ohio
Posts: 1,497
|
deleted
__________________
"The best diplomat I know is a fully charged phaser bank" - Montgomery Scott |
May 31, 2012, 01:01 PM | #3 |
Moderator Emeritus
Join Date: June 25, 2008
Location: Austin, CO
Posts: 19,578
|
Off to see The Smithy...
__________________
Nobody plans to screw up their lives... ...they just don't plan not to. -Andy Stanley |
May 31, 2012, 07:04 PM | #4 |
Senior Member
Join Date: June 29, 2011
Posts: 931
|
Friend of mine has an Arisaka - got to shoot it a few days ago. Loved the rifle, the ammo is expensive (unless you reload).
__________________
Ex - Navy, Persian Gulf Veteran. Loved shooting the M14, 1911, M60, M2 |
May 31, 2012, 08:28 PM | #5 |
Senior Member
Join Date: August 24, 2001
Location: LC, Ca
Posts: 1,917
|
I had that occur to me some 20+ years ago, but I cannot remember how I fixed it.
I would start by removing the barreled action from the stock. Then remove the trigger and sear assembly. Push out 1 pin and the trigger/sear comes off. The hazy part is that I was doing something with the safety while lifting the bolt handle. I think I depressed the safety slightly while lifting the bolt handle, but I'm not sure. I do remember that it didn't require force/broken parts and the entire process seemed easy afterwards. |
May 31, 2012, 08:44 PM | #6 |
Member
Join Date: January 17, 2009
Location: Cookevill,Tn
Posts: 44
|
try turning the back of the bolt /saftey either way I seem to rember on mine that it was the saftey causing the problem.
|
May 31, 2012, 09:00 PM | #7 |
Senior Member
Join Date: March 11, 2010
Location: South East Pa.
Posts: 3,364
|
It is a poor description of what is going on. Going by your description, the gun is on safe and there is nothing wrong with it. My guess would be the locator stud on the front of the safety knob has been forced out of the slot in the F/pin and is jammed there. Do as DNPark said earlier and remove the trigger and sear block. Then you may be able to realign the hook on the F/pin with the safety stud and bolt handle. Use a brass drift to tap on the receiver and bolt as they are fairly soft and will gouge and bend easily. It may be something as simple as a missing F/pin spring. Good luck.
|
June 1, 2012, 04:13 AM | #8 |
Senior Member
Join Date: December 27, 2008
Posts: 555
|
AFD,
This is a simple fix and no 'smith is needed unless you are new to guns and feel you would not recognize damaged or altered parts. I responded in a post dated January 14th of this year on THR with photos and a fairly detailed dis-assembly procedure. Am betting this is your situation. You can find it on that site with the keywords 'Japanese 38' or searching my handle. Sounds like the firing pin sear lug is in the bolt release area. Unless parts have been modified this is a result of incorrect assembly by someone, not a design failure. This is a five minute process with the barreled - CHECK the barrel for a round!! as described - action out of the wood. Cost will be for you to post a couple of photos when you get it put back together. Let's hear back now, JT |
June 1, 2012, 05:22 AM | #9 |
Senior Member
Join Date: August 30, 2009
Location: Northern AZ
Posts: 7,172
|
I, too, had that problem a couple times, but more than 20 years ago. I think it facilitates the fix if you remove the bolt release, if I remember correctly.
It also seems to me that I was able to get it back working by "fiddling" with it each time. As was stated prior, it's more or less a design flaw, and not something broken. Last edited by gyvel; June 1, 2012 at 05:28 AM. |
June 1, 2012, 08:03 AM | #10 |
Senior Member
Join Date: February 28, 2008
Location: Michigan
Posts: 2,618
|
The rear of the bolt/cocking piece is checkered. It's that way for a reason. With the heel of your hand push in and rotate the cocking piece. That action should bring everything into alinement and unlock the bolt.
|
June 1, 2012, 05:12 PM | #11 | |
Senior Member
Join Date: August 30, 2009
Location: Northern AZ
Posts: 7,172
|
Quote:
The first time it happened to me was at a gun show in the 80s when some joker somehow managed to get the bolt on a Type 38 on my table in that condition. It took me about 20 minutes of "fiddling" until I finally got it free. The second time (on another Arisaka) was not too many years after that, and I more or less knew what to do, but even that was more than 20 years ago. |
|
Thread Tools | Search this Thread |
|
|