|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
November 22, 2008, 09:58 PM | #1 |
Member
Join Date: January 20, 2007
Posts: 18
|
Refinishing Stock Question?
I am refinishing the stock on an old CVA kit gun and after reshaping the stock to fit the buttplate and sanding the entire stock to remove the finish I find that there are shaded areas of the stock where the original stain is still showing through. I don't dare sand these areas anymore as I'm afraid of removing too much wood. Is there anything I can do to either remove this stain or try to somehow blend the new finish in so thst it looks somewhat even all over?
|
November 23, 2008, 09:11 AM | #2 |
Senior Member
Join Date: August 15, 2006
Posts: 434
|
you might try a mild bleach solution on the darker spots. Another thing is that if you refinish it the way it is,it might have a really unique look about it .
|
November 23, 2008, 02:30 PM | #3 |
Senior Member
Join Date: February 16, 2006
Location: IOWA
Posts: 8,783
|
mega twin + 1
You can get stock bleach from Brownells. After that process, do a very light sanding then wipe off with mineral spirits and see what it looks like. You can repeat the process as you wish and then after that, you should stain the entire stock. These CVA's seem to like the redder darker stains but you can go with a light cherry or anique oak. Try different stains until you get one that pleases you. I once redid a stock that was stained dark and to this day, don't know what in the world the guy used. I was forced to restain and keep it dark. In the end, after the final finish, you could not see the blotches. Congratulations on the fitting as I think this is the hardest and most important part of the process. Be Safe !!! |
November 23, 2008, 02:39 PM | #4 |
Senior Member
Join Date: April 3, 2005
Location: Rochester, New York
Posts: 2,136
|
Most stains people see on the shelf is an oil/solvent based stain. There is also a Dye type stain, mostly commercial applications, that will really go deep and change the woods appearance fairly permanently.
|
November 23, 2008, 06:45 PM | #5 |
Senior Member
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
|
Try stripping the stock with CitriStrip. You can get it at Home Depot, Lowes, WalMart, you name it. If there is finish on the stock, it will remove it.
__________________
Never try to educate someone who resists knowledge at all costs. But what do I know? Summit Arms Services |
November 23, 2008, 08:55 PM | #6 |
Member
Join Date: January 20, 2007
Posts: 18
|
Stock Refinishing Question?
Thanks for all of the helpful suggestions on the stock problem now heres another problem that I created to help me with. I am also installing a set of Williams fiber optic sights on this gun, the rear sight was no problem but the front sight was another story. The package said there would be fitting required on the front sight so in the process of filing and fitting I managed to get the fit too loose and since I can't unfile the metal back I'm left with adding some sort of adhesive to hold the sight tight or a little JB Weld set and filed in the dovetail to take up the slack and hope it snugs up. The gun is an old cheapy so it's not a catastrophy but I want to do the best job I can on it. Any input on this situation would be greatly appreciated.
Thanks, Mthom |
November 23, 2008, 09:47 PM | #7 |
Senior Member
Join Date: April 7, 2006
Posts: 10,979
|
Hammer the dovetail closed a little.
|
November 23, 2008, 10:05 PM | #8 |
Member
Join Date: January 20, 2007
Posts: 18
|
I've already reblued the barrel, won't this screw up the finish a bit
|
November 23, 2008, 11:02 PM | #9 |
Senior Member
Join Date: April 3, 2005
Location: Rochester, New York
Posts: 2,136
|
You can also try to use a pointed punch to raise the metal in the bottom of the dovetail, Insert the sight and with a flat point punch sort of stake the sight in place by bending the very edge of the dovetail into the sight.
|
November 23, 2008, 11:08 PM | #10 |
Senior Member
Join Date: April 7, 2006
Posts: 10,979
|
Pad it with leather, and use a very small hammer.
|
November 24, 2008, 12:54 AM | #11 |
Senior Member
Join Date: February 9, 2008
Location: Puget Sound Washington
Posts: 1,553
|
+1 on the citrus strip.... That Scorch guy knows his stuff. I've used it too. You can re-apply it and control how much the stain is reduced after the initial stripping is done. It's way less toxic than traditional products but works like a champ.
__________________
"If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun." The Dalai Llama (5/15/01, The Seattle Times) "That rifle on the wall of the labourer's cottage or working class flat is the symbol of democracy. It is our job to see that it stays there." George Orwell |
November 24, 2008, 02:12 AM | #12 |
Senior Member
Join Date: April 3, 2005
Location: Rochester, New York
Posts: 2,136
|
Inspector: If a dye stain was used, no amount of stripper is going to make a difference. Most wood bleaches won't work either. Dye stains are made to be more than permanent, as in forever.
|
November 24, 2008, 05:31 PM | #13 | ||
Senior Member
Join Date: February 16, 2006
Location: IOWA
Posts: 8,783
|
Quote:
Quote:
Be Safe !!! |
||
November 24, 2008, 07:49 PM | #14 |
Member
Join Date: January 20, 2007
Posts: 18
|
Stock Refinishing Question?
Thanks again guys for all of the advice one of these should work.
|
Thread Tools | Search this Thread |
|
|