The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools Search this Thread
Old May 2, 2012, 01:02 AM   #1
jlb43
Senior Member
 
Join Date: March 26, 2010
Location: North Georgia
Posts: 128
Need a nipple

I picked up an old (1963) Replica Arms 1849 pocket last week that came with a missing nipple and a broken wrench. I have looked around the internet and all of the sources I found say it should be a 5.5mm x.9 thread but when I checked and measured one of the others I come up with 12 - 24 thread. A screw of that size fits perfectly also. My problem is I cannot find that size and a couple of emails to parts houses have gone unanswered. I do not plan to shoot it but it is in pretty decent shape otherwise and is part of a cased set so I would like for it to be complete. Anybody have any suggestions?

Jim
jlb43 is offline  
Old May 2, 2012, 02:09 AM   #2
arcticap
Senior Member
 
Join Date: March 15, 2005
Location: Central Connecticut
Posts: 3,166
The outfit that's mentioned in the following post probably makes them:

http://thefiringline.com/forums/show...21&postcount=3

Or you can try asking Track of the Wolf:

http://www.trackofthewolf.com/
arcticap is offline  
Old May 2, 2012, 08:17 AM   #3
wogpotter
Senior Member
 
Join Date: September 27, 2004
Posts: 4,811
Could it be this:
12X28tpi, Same as for: Ruger Old Army. Thompson Seneca rifle, Colt revolvers?
I had a nipple replacement problem & discovered that "5.5mm x.9" is just the metric description of a 12X28.
__________________
Allan Quatermain: “Automatic rifles. Who in God's name has automatic rifles”?

Elderly Hunter: “That's dashed unsporting. Probably Belgium.”
wogpotter is offline  
Old May 2, 2012, 11:26 AM   #4
mykeal
Senior Member
 
Join Date: October 8, 2006
Location: Northern Michigan
Posts: 2,772
12/28 or 5.5x.9 won't work if his gun is truly threaded at 12x24. I've never encountered a c&b revolver with coarse nipple threads. 24 tpi is the coarse standard for the #12 screw diameter; 28 tpi is the fine thread standard for that diameter and is by far more common.

Are you sure it's 12x24 and not 12x28?
mykeal is offline  
Old May 2, 2012, 02:08 PM   #5
jlb43
Senior Member
 
Join Date: March 26, 2010
Location: North Georgia
Posts: 128
I have come the conclusion that since the 5.5 x.9 threads are nearly identical to the 12-24 I will have to try the 5.5X.9 threads. If they don't fit then they don't fit. I measured the nipple with my trusty sawtooth thread gauge once again and it for sure is not 28 threads per inch. The 24 TPI gauge sits down into the tread perfectly the 28 TPI is not even close.

This gun is marked Replica Arms El Paso, TX so maybe the nipples came from over the border. LOL

Thanks for your assistance I really do appreciate it.

jlb
jlb43 is offline  
Old May 3, 2012, 06:17 AM   #6
mykeal
Senior Member
 
Join Date: October 8, 2006
Location: Northern Michigan
Posts: 2,772
Uh, no, 5.5x.9 are NOT close to 12x24; they're almost exactly 12x28. 24 tpi is 1.06mm pitch, not 0.9mm. You would need a 5.5x1 metric thread to come close to 12x24.
mykeal is offline  
Old May 3, 2012, 08:19 AM   #7
Rifleman1776
Senior Member
 
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
Since there is some confusion, take out another nipple and send it to Track of the Wolf. Ask them to send you six new nipples and a wrench.
There is a danger in putting in wrong size, or thread, nipples. They can blow out at you.
Rifleman1776 is offline  
Old May 9, 2012, 01:43 PM   #8
jlb43
Senior Member
 
Join Date: March 26, 2010
Location: North Georgia
Posts: 128
I misspoke in the last post. I did buy a 5.5 X.9 nipple from Trac of the Wolf to see if it would fit and it does not. Since the existing nipples measure .216" on the thread OD, and screw into the cylinder perfectly, I have to conclude there is no other nipple made, in a thread other than 12-24 or 5.5 X 1.05 (neither of which exists), that will fit. I talked with a local gunsmith who has been repairing black powder weapons for many years and he said if I brought the cylinder and nipples in he would look at it but from what I told him he thought a custom made nipple might be the only solution. I will do that when I get time someday but for now I wlll just leave the hammer in the empty recess. I have no intentions whatsoever to ever fire, or attempt to fire, the gun. It is, and will be, a safe queen.

Thanks to all of you for your ideas.
jlb43 is offline  
Old May 9, 2012, 05:31 PM   #9
KEYBEAR
Senior Member
 
Join Date: January 11, 2012
Location: Indiana
Posts: 1,059
NIPPLES

I have six used nipples from a Ruger Old Army you can have If you need to try them .
KEYBEAR is offline  
Old May 17, 2012, 10:34 AM   #10
jlb43
Senior Member
 
Join Date: March 26, 2010
Location: North Georgia
Posts: 128
Keybear

I have been away for a few days. Thanks for your offer. I bought some "so called" baby dragoon nipples on gun auction last week and I am waiting for them. They were described as smaller than "regular" nipples and the close up photos show three turns of thread on them. When I compared that to mine it looked the same. They did not look like the fine thread nipples I own so I gambled a couple of bucks. Nothing like precision measurements. Ha Ha
jlb43 is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:32 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.04277 seconds with 10 queries