The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools Search this Thread
Old April 14, 2013, 10:12 AM   #1
kealil
Senior Member
 
Join Date: July 27, 2011
Posts: 270
Previous owner screwed things too tight...

Hello all!

I recently purchased another Smith and Wesson 422 6" and as per my ritual I broke it completely down and cleaned it insided and out....or at least I would have if the screws weren't so tight.

Whoever took this gun apart last screwed the screws so tight that it ruined two bits off of my precision screwdriver set.

They also screwed the thread guard really tightly as well.

I have never run into this problem on a gun before. I know that for other really tight screws I just take a blow torch to em and out they come. I dont think that would be wise here.

Any tips for getting these screws out without destroying my finish or the gun in general for that matter?

Thanks!
__________________
"A weapon without a name is nothing; Just another hunk of steel, wood, or what have you. A weapon with a name is more. It is a partner, a friend, and a comrade to the end"
kealil is offline  
Old April 14, 2013, 10:29 AM   #2
g.willikers
Senior Member
 
Join Date: September 28, 2008
Posts: 10,442
They might have used a threat securing goop, like locktite.
Try soaking the screw in acetone and hope it gets down into the thread area.
Then use an impact screw driver, the kind with internal weights, that you twist while banging with a hammer.
Another method requires having a drill press, and hand turning the press head while applying pressure with the handle.
__________________
Walt Kelly, alias Pogo, sez:
“Don't take life so serious, son, it ain't nohow permanent.”
g.willikers is offline  
Old April 14, 2013, 10:36 AM   #3
polyphemus
Senior Member
 
Join Date: June 24, 2012
Posts: 1,055
I'd try a heat gun instead of a torch,you probably need extra torque on the
screwdriver to assist turning,I use a small wrench on the flats and secure the
part well.Tough cases don't tend to respond to the lubricating approach and
make it hard to apply any heat afterwards,fumes and so on.Patience pays
good luck.
polyphemus is offline  
Old April 14, 2013, 04:16 PM   #4
Harry Bonar
Senior Member
 
Join Date: December 5, 2004
Location: In the Vincent, Ohio general area.
Posts: 1,804
screws

Sir;
If the slots are still there put a screwdriver bit into them and lightlt tap with a small ball peen hammer! That, many times will fracture tightened screws even with loc-tite.
Greywolf
Harry Bonar is offline  
Old April 14, 2013, 04:46 PM   #5
Evan Thomas
Senior Member
 
Join Date: July 7, 2008
Location: Upper midwest
Posts: 5,631
Even better than a heat gun or blowtorch: set the tip of a small soldering iron in the slot of the screw. It keeps the heat very localized, and it doesn't take long.
__________________
Never let anything mechanical know you're in a hurry.
Evan Thomas is offline  
Old April 15, 2013, 10:35 PM   #6
nanewt02
Senior Member
 
Join Date: February 25, 2013
Posts: 249
i was going to say one of those pen toches but a soldering iron seems much better
nanewt02 is offline  
Old April 18, 2013, 10:51 PM   #7
PVL
Senior Member
 
Join Date: February 20, 2013
Posts: 169
Another vote for the soldering iron - and tapping it with a hammer too.

Heat it up, jar it loose.

And of course use a flat-ground screwdriver that fits the slot exactly.

Sometimes I use Kroil, letting it soak in overnight.

I used to have a security outfit bring me a shoe-box full of .38 snubbies to look over once a year, whether they needed it or not. - Every once in a while I would run across a stubborn screw like that.

Good luck, and let us know how it goes.
PVL is offline  
Old April 19, 2013, 02:22 AM   #8
natman
Senior Member
 
Join Date: June 24, 2008
Posts: 2,604
+1 for Kroil. I once had a set of scope hole plugs I had to remove that had been in place since the gun was built 40 years prior. They wouldn't budge and the tiny heads were in danger of stripping. A drop of Kroil each, an overnight soak and the next morning the plugs spun out at the first touch. It's amazing stuff.
natman is offline  
Old April 19, 2013, 02:29 AM   #9
Sport45
Senior Member
 
Join Date: May 25, 1999
Location: Too close to Houston
Posts: 4,196
If you don't have Kroil, I've found Ed's Red to work for this sort of thing too. The ATF thinned with acetone and mineral spirits is a great penetrator.
__________________
Proud member of the NRA and Texas State Rifle Association. Registered and active voter.
Sport45 is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:01 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.06916 seconds with 10 queries