The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Bolt, Lever, and Pump Action

Reply
 
Thread Tools Search this Thread
Old August 23, 2013, 11:10 PM   #1
btmj
Senior Member
 
Join Date: November 1, 2011
Location: Near St. Louis, Missouri
Posts: 864
Marlin 336 what kind of accuracy should I expect ?

I just recently sighted in my 336C in 30-30 (actually it is my wife's gun). It has a 20" barrel and a Leupold 2.5x scope.

It seems to make a consistent 1" group at 50 yards, 2" group at 100 yards. It does this with just about any 150 grain ammo I put through it. But I can't get the groups to tighten up beyond that.

Is 2 MOA what I should expect for this rifle? It is plenty accurate for hunting, no question. But I have become spoiled by my bolt gun and my AR-15, and I am just wondering if 2 MOA is the reasonable limit of this gun.

Jim
btmj is offline  
Old August 23, 2013, 11:24 PM   #2
reynolds357
Senior Member
 
Join Date: December 10, 2012
Posts: 6,158
2" at 100 is a good group for a stock 336. Its not a bad group for one that has had a lot of work done on it.
reynolds357 is offline  
Old August 23, 2013, 11:27 PM   #3
math teacher
Senior Member
 
Join Date: February 5, 2012
Location: Southwest WA Coast
Posts: 558
Individual rifles vary, but that is in the norm for that rifle. About the same as mine. If you go back and read Jack O'Connor from the 1940s, he thought 2 inch groups for his beloved Model 70 was just fine. We are really spoiled with the accuracy of many of today's rifles.
math teacher is offline  
Old August 23, 2013, 11:29 PM   #4
Weatherby Fan
Member
 
Join Date: May 9, 2013
Posts: 40
I have a new Marlin 336 with a williams FP-336 aperture sight installed using the stock front blade.

From a solid rest, the rifle will pattern less than 2" groups at 200 yards.

It's sub-moa.

I've been very pleased with it.

I recall last year (new last year) embarrassing a friend at the range would couldn't group into 3" at 200 yards with his scoped bolt action rifle. His face literally turned red when we were standing at the 200 yard target boards and he looked at my target.

Usually, it's the indian more than the arrow.

YMMV.
Weatherby Fan is offline  
Old August 24, 2013, 01:36 AM   #5
wrm
Member
 
Join Date: August 11, 2010
Location: Cape Town, South Africa
Posts: 52
It took me years of load development to get 2" at 100. The 336 only does it with Sierra 170gr bullets, Winchester primers, and a very specific COL.

Note I'm shooting five shot groups, none of y'all are saying how many shots in your groups.

I think your 336 is a keeper.
wrm is offline  
Old August 24, 2013, 01:58 AM   #6
SteelChickenShooter
Senior Member
 
Join Date: May 12, 2011
Posts: 863
I agree based on my 336 which is very similar. Your groups are ok and what I would be happy with, especially if it's just for hunting.
SteelChickenShooter is offline  
Old August 24, 2013, 05:42 AM   #7
steveNChunter
Senior Member
 
Join Date: December 14, 2012
Location: Southern Appalachian Mtns
Posts: 1,520
With the quality control (or lack thereof) of the newer Marlins, 2 MOA is great. I have an early 70's 336 in .35 rem that shoots MOA, but only with Hornady Lever-evolution ammo. Corelokts are about 1.5-2 MOA. I haven't got around to reloading for it yet, my bolt actions get most of the attention at the reloading bench.
__________________
DEO VINDICE
steveNChunter is offline  
Old August 24, 2013, 06:08 AM   #8
jmr40
Senior Member
 
Join Date: June 15, 2008
Location: Georgia
Posts: 10,786
What you are seeing is typical. If you handload it might be possible to get a little better. It is the rare lever action that consistently shoots under 2" @ 100.
jmr40 is offline  
Old August 24, 2013, 08:18 PM   #9
btmj
Senior Member
 
Join Date: November 1, 2011
Location: Near St. Louis, Missouri
Posts: 864
Thanks all,

I was pretty sure I knew that answer when I posted. but hey, it is nice to hear other folks experience.

Weatherby Fan... sounds like you have an exceptional rifle. Don' sell it...

With my Vangaurd in 243 I can shoot a 0.8 inch 5 shot group... Notice I say I can... meaning I have done it on several occasions.... typical for me is a 1.2 inch group. But if I am having a really good day and everything is clicking... I can get the groups under an inch. I am sure I am not shooting at the limits of this gun, but the very fine trigger makes me think that perhaps I am shooting close to the limit.

With the Marlin? I'm not sure if the inherent accuracy is 2 MOA, or if the heavier trigger pull and the longer lock time mean that 2 MOA is the best that I can shoot with it. For all I know, the gun is capable of sub MOA, but I can't do it due to the trigger and locktime...

Jim
btmj is offline  
Old August 24, 2013, 08:29 PM   #10
jimbob86
Junior member
 
Join Date: October 4, 2007
Location: All the way to NEBRASKA
Posts: 8,722
2" @ 100 is fine for just about anything that needs shot with a 30/30.

It wasn't meant to be a benchrest gun- it has more practical uses.
jimbob86 is offline  
Old August 24, 2013, 09:04 PM   #11
reynolds357
Senior Member
 
Join Date: December 10, 2012
Posts: 6,158
Wby fan, I would have to disagree with it "usually being the Indian and not the arrow." This same Cherokee Injun can shoot a 10 shot group with my bench rifle that looks like three or four elongations on a hole. It does not look like a clover leaf, it looks like a ragged hole. Having said that, my Marlin 336 is not going to shoot under 1.5@ 100 come hell, high water, drought, and any ammo you want to put through it. With most ammo, it shoots close to 3". I would be thrilled if my 94 Winchester would shoot a 3 moa group.
reynolds357 is offline  
Old August 25, 2013, 01:05 AM   #12
Weatherby Fan
Member
 
Join Date: May 9, 2013
Posts: 40
Sounds like I got lucky with my Remlin

Although shooting a bench rifle is totally different than shooting a level with a heavy trigger. Totally different skills required.

Shooting aperture sights is different than shooting with a scope, too.
Weatherby Fan is offline  
Old August 25, 2013, 06:38 PM   #13
Ramon_
Member
 
Join Date: August 7, 2011
Posts: 27
With Leverevolution (if you do your part of course) you can be drop dead accurate out to 200 yards. I frequently take hogs out to that distance.
Ramon_ is offline  
Old August 25, 2013, 06:47 PM   #14
Toney
Senior Member
 
Join Date: August 17, 2005
Location: Stillwater Oklahoma
Posts: 790
Really with it's straight jacket devices, anything better than 3"
Toney is offline  
Old August 25, 2013, 07:02 PM   #15
reynolds357
Senior Member
 
Join Date: December 10, 2012
Posts: 6,158
Wby Fan, Shooting my 336 off a bench and shooting my BAT off a bench are not very different. The only major difference is round vs flat bottom and 2 oz vs 1.2 pound trigger. The 336 has a custom trigger. The trigger and the round bottom are not the major differences in group size.

Last edited by reynolds357; August 25, 2013 at 07:17 PM.
reynolds357 is offline  
Old August 26, 2013, 05:54 AM   #16
Salmoneye
Senior Member
 
Join Date: December 31, 2011
Location: Vermont
Posts: 2,076
Try 170gr bullets, OP...
Salmoneye is offline  
Old August 26, 2013, 06:05 AM   #17
s3779m
Senior Member
 
Join Date: November 12, 2012
Location: Lometa, Texas
Posts: 331
So is there a lever 30-30 that can shoot 1". 2" is fine for white tails but just wondering?
s3779m is offline  
Old August 26, 2013, 06:07 AM   #18
Mobuck
Junior member
 
Join Date: February 2, 2010
Posts: 6,846
Plenty good enough considering the effective range of the cartridge.
I've seen those rifles vary in POI and group size depending on how many rounds were loaded in the mag(among other factors).
Mobuck is offline  
Old August 26, 2013, 06:14 PM   #19
cdbeagle
Senior Member
 
Join Date: January 3, 2012
Location: Justin Texas
Posts: 313
My son's Remlin 336W shoots 1" with 150 gr Core-Lokts after I did some serious polishing on the bolt and action and installing a Happy Trigger. Now that he has reached full growth a 30-30 is beneath him, he shoots his AR or 30-06. It sports a Vortex Viper 2-7 and has found a happy home as my truck gun.
__________________
Assistant Secretary - U.S. Dry Bean Council
cdbeagle is offline  
Old August 26, 2013, 07:40 PM   #20
flintlock.50
Senior Member
 
Join Date: July 1, 2009
Posts: 233
If you are getting 2 inch groups at 100 yards with a Micro-Groove® barrel, I'd consider that outstanding (compared to what I've seen). Check out the picture below.



This was a .30-30 at 25 yds. We got the same result with several different brands of ammo. Needless to say, the groups got MUCH worse at longer distances. ALL of the ammo we tried produced keyholes like this. This rifle is getting a new barrel as you read this.
__________________
NRA Benefactor member; NRA rifle and home firearm safety instructor; NMLRA member; NMLRA instructor for rifle, pistol and shotgun

A government that takes from Peter to pay Paul can always count on Paul's vote!

Last edited by flintlock.50; August 26, 2013 at 07:53 PM.
flintlock.50 is offline  
Old August 26, 2013, 08:35 PM   #21
steveNChunter
Senior Member
 
Join Date: December 14, 2012
Location: Southern Appalachian Mtns
Posts: 1,520
Quote:
If you are getting 2 inch groups at 100 yards with a Micro-Groove® barrel, I'd consider that outstanding (compared to what I've seen).
flintlock .50,

Trust me the Micro-Groove barrel is not the problem unless you just got a bad barrel. I have one in .35 rem that is MOA on a good day with the right load and I know several other 336 owners personally who get great accuracy out of their Micro-Groove barrels.

The picture looks like either trying to shoot a bullet too heavy for the twist rate or there is severe damage to the rifling. No Micro-Groove in good condition without factory flaws would do that.

Could we see a pic looking down the bore?
__________________
DEO VINDICE
steveNChunter is offline  
Old August 26, 2013, 08:43 PM   #22
flintlock.50
Senior Member
 
Join Date: July 1, 2009
Posts: 233
steveNChunter: A friend, former army captain, avid hunter and shooter owns the rifle. He had not shot this rifle much. I am certain the barrel has been well cared for, though it could be just a bad barrel. It's also possible the bullets are too heavy, though we shot about 4 different brands that day. I can't recall what weight bullet or brands. In any case, the bullet obviously wasn't being stabilized. He decided just to get the rifle re-barreled.

I saw the same thing decades ago with some hand loaded .264s. Not sure what kind of rifle. Every shot keyholed.
__________________
NRA Benefactor member; NRA rifle and home firearm safety instructor; NMLRA member; NMLRA instructor for rifle, pistol and shotgun

A government that takes from Peter to pay Paul can always count on Paul's vote!
flintlock.50 is offline  
Old August 26, 2013, 09:06 PM   #23
reynolds357
Senior Member
 
Join Date: December 10, 2012
Posts: 6,158
Assuming that the bullets are not entirely too long, Its either a worn out or defective barrel. The micro groove barrel is a good barrel for jacketed bullets. Won't do wonders with cast, but good for jackets.
reynolds357 is offline  
Old August 26, 2013, 09:13 PM   #24
Axelwik
Senior Member
 
Join Date: March 12, 2012
Location: Land of Enchantment
Posts: 436
Mine is pretty accurate even with cast. It's a Remlin.
Axelwik is offline  
Old August 27, 2013, 06:07 AM   #25
Salmoneye
Senior Member
 
Join Date: December 31, 2011
Location: Vermont
Posts: 2,076
Quote:
Won't do wonders with cast
Cast works fine in MG barrels...

Slug your bore and size your boolits .002 over groove diameter...
Salmoneye is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:17 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.15364 seconds with 10 queries