June 12, 2008, 11:00 AM | #1 |
Senior Member
Join Date: December 13, 2006
Location: Body: Clarkston, Washington. Soul: LaCrosse, Wisconsin
Posts: 1,591
|
7.62 reloading
Would it be possible to use the same slugs for 7.62x39, 7.62x51, 7.62x54, and 7.62x63 (.30'06)? Looking at the x39 it seems a little different on the tip since they are designed for detatch mags maybe?
__________________
- Jon Disequilibrium facilitates accommodation. 9mm vs .45 ACP? The answer is .429 |
June 12, 2008, 11:51 AM | #2 |
Senior Member
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
|
Yes, it would be possible, but it would be a great waste of time and money. 7.62X39- bore diameter= .310"-.312"
7.62X51 and 7.62X63- bore diameter= .308" So, you can see that you would have to use the smaller diameter bullet (.308") in all the cartridges, and accuracy out of the 7.62X39 would be terrible due to poor obturation (bullet-bore fit). Plus, the larger cartridges are designed for heavier bullets than are practical with the 7.62X39.
__________________
Never try to educate someone who resists knowledge at all costs. But what do I know? Summit Arms Services |
June 12, 2008, 11:56 AM | #3 |
Junior member
Join Date: January 26, 2007
Location: South-Western North Carolina
Posts: 1,124
|
some bullets are designed with jacket thickness in mind of velocity also. useing some '06 slugs or .308 in a X39 may not expand optimally at the lower velocitys.
|
June 12, 2008, 12:13 PM | #4 |
Junior member
Join Date: September 28, 2005
Location: Mesa, AZ
Posts: 6,465
|
Also... 7.62x54R is not a .308 diameter either. It's .310 to .312 as well. So is .303 British and the Japanese 7.7 Arisaka cartridge.
.308 (7.62x51, aka 7.62 NATO), .30-06 and .30-30 use .308 diameter bullets. So do all the current .300 <<insertbraggingrightshere>> whompem-magnum offerings. But, since the velocities of each cartridge are going to be different, you're gonna want to optimize bullet weight and construction for the intended purpose of the rifle. |
June 12, 2008, 05:03 PM | #5 | |
Senior Member
Join Date: December 23, 2005
Location: Minnesota
Posts: 2,952
|
Quote:
|
|
June 12, 2008, 06:54 PM | #6 |
Senior Member
Join Date: May 12, 2008
Location: Henrietta, FL
Posts: 306
|
It also depends what rifles the 7.62x39 and 7.62x54R are chambered in.
There is always the chance these rifles have .308" bores and are modern firearms. Unlikely - but possible. Without any more information from the OP, we won't know. IF they were all .308", it would be possible to settle on 2-3 different bullets that would cover the spectrum from 123-180 grain however you see fit. Whatever you do - If you want to reload for the two Russians, have the bores slugged by a gunsmith. It will tell you the exact bore diameter of the rifles. I wouldn't want to be the guy pulling the trigger on a .310" bored Mosin, with a .313" bullet in the throat.
__________________
Feel free to disagree with my opinion. -I do it all the time. |
June 12, 2008, 06:58 PM | #7 |
Senior Member
Join Date: December 13, 2006
Location: Body: Clarkston, Washington. Soul: LaCrosse, Wisconsin
Posts: 1,591
|
So if I were to be practical have a set for the 7.62x54 and 39 with another for the 7.62x51 and 63.
__________________
- Jon Disequilibrium facilitates accommodation. 9mm vs .45 ACP? The answer is .429 |
June 12, 2008, 07:57 PM | #8 |
Junior member
Join Date: January 26, 2007
Location: South-Western North Carolina
Posts: 1,124
|
I have had good results with the Speer 150gr .308 slug on paper so far. I don't have a chrono so can't say fps. I use 680 powder. this is at 100 yards. and my Ruger M30. it shoots about as good as I can hold it with my small glass.
|
June 13, 2008, 10:40 AM | #9 | |
Junior member
Join Date: September 28, 2005
Location: Mesa, AZ
Posts: 6,465
|
Quote:
But... the roles these cartridges play, the rifles for which they are chambered, are so inherently different that it is ridiculous to expect them to all use the same bullets. x39 = Ruski assault cartridge for SKS and AK47. Velocity ~2300fps @ 123gr. x54R = Ruski battle cartridge for Mosin and Dragunov. Velocity ~2800fps @150gr. x51 = NATO/US battle cartridge for FAL and M14. Velocity ~2700fps @ 150gr. x63 = US battle cartridge for 1903 and M1 Garand. Velocity ~2700fps @ 174gr. You can use the same bullets between .308 and .30-06 with similar results between 125 and 165 grains. You will never get matching performance from the x39 since it is only 39mm deep and has such small case capacity... and the bore is a couple thousandths larger. You can TRY .308 diameter bullets in an x54R, but chances are you will be let down. The pressure and case volume are similar enough for the same bullet weights though. The x54R will handle up to 180gr bullets pretty well, while most folks hold of the .308 around 168 or maybe 175gr for match-only bullets. I've shot light bullets from an x54R. 100gr round-nose... training cartridges. They had a full powder charge behind them, but the bullet was really light. They didn't strike anywhere near the "regular" hit zone of 150gr light ball or 180gr heavy ball. Way, way lower. Just my opinion, but handloading is completely without merit if your product isn't accurate from your platform. Using the same bullet for all these calibers will result in inaccuracy. Now... you can use the same PRIMERS and possibly even the same POWDER though. I'd suggest IMR4895 or H335 as two of many good candidates for bulk powder purchase for these four calibers. |
|
June 13, 2008, 11:28 AM | #10 | |
Senior Member
Join Date: February 3, 2007
Location: Western NY
Posts: 598
|
Quote:
The Russians will be a little trickier. If you try to use a 123-125gr bullet that your AK / SKS likes, your Nagant is probably going to over stabilize it. If you use a 150gr. in your 7.62x39mm, it's going to just about kill the ballistics. If the 7.62x39mm in question is a Mini-30 it has a 308 diameter bore instead of the 310-312 bore found on most guns in that caliber.
__________________
My Calibers: 22 Hornet, 223 Rem, 22-250, 243 Win, 270 Win, 280 Remington Ackley Improved, 30-30, 308 Win, 30-06, 300 Winchester magnum, 7.62x39mm, 380 Auto, 9mm Parabellum, 38 Special, 357 magnum, 40 S&W, 10mm Auto, 45 GAP, 45 Auto, 12 & 20 Guage |
|
June 13, 2008, 02:02 PM | #11 |
Senior Member
Join Date: May 12, 2008
Location: Henrietta, FL
Posts: 306
|
Red Eagle - Only pre-1993 Mini-30s have .308" bores. In 1993 Ruger began using .310" bores so the actions wouldn't take such a beating from .310" surplus ammo.
__________________
Feel free to disagree with my opinion. -I do it all the time. |
June 13, 2008, 03:34 PM | #12 | |
Senior Member
Join Date: December 23, 2005
Location: Minnesota
Posts: 2,952
|
Quote:
|
|
June 13, 2008, 07:48 PM | #13 |
Senior Member
Join Date: December 4, 1999
Location: WA, the ever blue state
Posts: 4,678
|
I buy allot of guns just to overload them.
I can't buy them all and test them, but I have tested CZ527 and SKS rifles and the 7.62x39mm case in large Boxer, Small Boxer, and Berdan. It is all a poor choice for overloading compared to a 98 Mauser with the 1889 7.65x53mm type case head in large Boxer. That would include 22-250, 243, 6mm Rem, 250 Savage, 257 Roberts, 25-06, 260 Rem, 6.5x55 [US brass], 270, 7mm-08, 7x57mm, 280, 308, 30-06, 8x57mm, 338F, 358, and 35W. Don't mess with those poor rifles, unless you want to pay for lots of replacement parts, like I have. |
|
|