The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: General Handgun Forum

Reply
 
Thread Tools
Old December 12, 2010, 08:40 PM   #1
javacontender
Junior Member
 
Join Date: December 12, 2010
Posts: 2
44 mag thompson contender

I have just purchased a 14" 44 mag contender. Really like the gun, i have shot two different rounds thru it. 240 gr winchester and 180 gr remington. I have noticed the remington loads to be a bit erratic. Was just wondering if this is normal and is there another load you guys are having good results with? Any help would be great.
javacontender is offline  
Old December 12, 2010, 08:52 PM   #2
markallen
Senior Member
 
Join Date: October 4, 2008
Location: N E Ohio
Posts: 187
The 14" barrel will give you more burn time on the powder charge, then a four, or six inch barrel.
With the longer burn time, the heavier bullet will be more stable. Plus since this a hunting, not a self defense gun, the rifling, and I'm not sure what the rate of twist in the T/C is, but the heavier bullets will be more stable.

At least that is what I found when I hand loaded for my T/C years ago.

If you don't hand load, stick with the heavier bullets, and try different factory loads that are the most accurate in your gun.
__________________
If your in a war, instead of throwing a hand grenade at the enemy, throw one of those small pumpkins. Maybe it'll make everyone think how stupid war is, and while they are thinking, you can throw a real hand grenade at them. www.sendoutcards.com
markallen is offline  
Old December 12, 2010, 10:10 PM   #3
Standing Wolf
Member in memoriam
 
Join Date: April 26, 2002
Location: Colorado
Posts: 1,649
The 180-grain bullet is decidedly light for the caliber. If you happen to like the bullet, you'll probably have to develop a powder charge for that specific barrel.

I predict if you try some rounds with 300-grain bullets, you'll be happy with the accuracy for the reasons markallen mentioned above.
__________________
No tyrant should ever be allowed to die of natural causes.
Standing Wolf is offline  
Old December 12, 2010, 10:30 PM   #4
javacontender
Junior Member
 
Join Date: December 12, 2010
Posts: 2
loads

Thanks guy's I appreciate the info. I will get some heavier loads and see how they shoot. Love the Gun!!!
javacontender is offline  
Old December 14, 2010, 07:01 PM   #5
Ozzieman
Senior Member
 
Join Date: December 14, 2004
Location: Northern Indiana
Posts: 5,027
Try the 320 GR SSK from Penn Bullets with 20 GR of H110. My contender loves them.
NOTE: This is not a safe load in many revolvers.
http://www.pennbullets.com/44/44-caliber.html

Last edited by Ozzieman; December 14, 2010 at 07:16 PM.
Ozzieman is offline  
Old December 14, 2010, 09:40 PM   #6
44 AMP
Staff
 
Join Date: March 11, 2006
Location: Upper US
Posts: 11,832
I have a 10", and it really recoils! Because its lighter than a 6" revolver! Your 14" should tame that a bit.

Can't say about factory loads, I haven't shot any in years in .44 magnum. Sorry. However, I don't buy the light bullets are no good idea. I think its more likely that its is your individual gun's preference. Every gun is different, and some loads just don't work as well in some guns as they do in others.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better.
44 AMP is offline  
Old December 15, 2010, 08:03 AM   #7
darkgael
Senior Member
 
Join Date: February 9, 2006
Location: Homes in Brooklyn, NY and in Pennsylvania.
Posts: 4,355
.44

+1 about the recoil of the ten inch barrel. While I very much like the portability of the shorter barrel, it does come back. I went through three "recoil proof" red dots before I found one that could take the Gs.
The 14" should tame that a bit.
Pete
__________________
“Auto racing, bull fighting, and mountain climbing are the only real sports ... all others are games.” Ernest Hemingway ...
NRA Life Member
darkgael is offline  
Old December 15, 2010, 10:24 AM   #8
lashlaroe
Senior Member
 
Join Date: November 20, 2010
Location: Central Florida
Posts: 180
I've seriously considered getting a 14" .44 mag barrel for my Contender as a stand-in for my favorite round in the Contender, .357 max that my brother has.

I'd be happy if I could even get close to the accuracy of his combo.

Did you scope yours or just iron sights?
__________________
Mike

As much as I believe that there is good in every person, I'm not so naive as to think that all people are essentially good. Evil and evil people exist. Deny that fact at your own risk.
lashlaroe is offline  
Old December 15, 2010, 08:05 PM   #9
frumious
Senior Member
 
Join Date: May 13, 2009
Location: Carrollton TX
Posts: 521
I have a TCC with the choked .44 barrel, like this:



I guess the barrel is only about 8" with the choke removed. Recoil is fierce (to me) with full-house magnum loads using a 240 gr RNFP cast lead bullet. So I have been loading that same bullet over a much milder 6-7 grains of Green Dot in order to make a more pleasant shooting experience. Sort of a .44 special +P+ :-)

Good luck with your gun; I love mine too.

-cls
frumious is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:23 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07689 seconds with 9 queries