December 10, 2001, 08:48 PM | #1 |
Junior member
Join Date: July 14, 2001
Location: Bedford, NH
Posts: 72
|
Speedfeed Stocks
I have a Speedfeed stock on my Rem870 Police, which has AO Express Pro rifle sights. Two questions:
1. It seems when I put my cheek on the stock, that my line of sight is a bit low for the AO rifle sights. I've seen Cheek-Eez comb stick on Sorbothane pads ranging 1/16 - 1/4". Are these good, or are there better options? 2. The Speedfeed recoil isn't too impressive - but I can't figure how to remove it. Do I slice it off and glue on a Pachmayr Decellerator pre-fit size for a Rem870? BRET |
December 10, 2001, 09:50 PM | #2 |
Senior Member
Join Date: March 25, 1999
Posts: 3,147
|
Re: removal of the pad.
Mine has a pair of phillips head screws on the actual butt of the stock, you just unscrew 'em.
Mike
__________________
The axe bites into the door, ripping a hole in one panel. The maniac puts his face into the hole, cackling gleefully, "Here's Johnny...erk." "And here's Smith and Wesson," murmurs Coronach, Mozambiquing six rounds of .357 into the critter at a range of three feet. -Lawdog "True pacifism is the finest form of manliness. But if a man comes up to you and cuts your hand off, you don't just offer him the other one. Not if you want to go on playing the piano, you don't." -Sam Peckinpah "A human being should be able to change a diaper, plan an invasion, butcher a hog, conn a ship, design a building, write a sonnet, balance accounts, build a wall, set a bone, comfort the dying, take orders, give orders, cooperate, act alone, solve equations, analyze a new problem, pitch manure, program a computer, cook a tasty meal, fight efficiently, die gallantly. Specialization is for insects." -Robert Heinlein |
December 10, 2001, 11:03 PM | #3 |
Senior Member
Join Date: October 13, 2000
Posts: 425
|
The holes for the two screws are coverd by a thin layer of rubber. Take a medium phillips screwdriver, wet the tip, and push it through the small hole in the rubber which may look like a small inperfection to you. When you pull the screwdriver out it the thin rubber closes back on the hole making it look like there is no hole.
|
December 11, 2001, 05:35 AM | #4 |
Staff In Memoriam
Join Date: October 13, 1999
Location: Columbia, Md, USA
Posts: 8,811
|
The Cheek Eez pads work. They will move your face out from the stock as much as up unless you cut them in half and use the half to raise your weld by placing it on top.
|
December 12, 2001, 09:37 PM | #5 |
Junior member
Join Date: July 14, 2001
Location: Bedford, NH
Posts: 72
|
Got the recoil pad off as indicated, but the butt of the polymer stock measures 4 11/32 (4.348") x 1 17/32 (1.531") at widest points, which doesn't seem to match any Pachmayr pre-fit pads. Maybe Speedfeed stocks won't take softer pads?
BRET |
December 12, 2001, 10:32 PM | #6 |
Senior Member
Join Date: January 6, 2000
Location: SE PA
Posts: 1,049
|
Those pre-fit Pachmayrs are easily shaped. The critical part is the alignment of the screw holes.
I bought a pre-fit for the Wingmaster and one for the Express. The dimensions were similar (actually the Wing was closer) but the Wingmaster holes were off enough that the pad would have been too high and I would have had a step from the stock-to-pad at the bottom. Anyone know Cabela's return policy? Perhaps you could try a couple that have dimensions that are slightly larger just to see if you get full coverage when the holes are aligned. Then you could massage it to fit. Mike
__________________
"Freedom is not free" Visit TheRallyPoint.org TheRallyPoint at LRGC- Saturday August 26th IF YOU LIVE IN PA AND DID NOT VOTE, YOU DESERVE TO LOSE YOUR GUNS! |
|
|