|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
December 13, 2012, 04:04 PM | #1 |
Senior Member
Join Date: December 27, 2006
Location: Wisconsin
Posts: 1,475
|
How Many Agree With This
I reload with lead cast bullets, and using my Lee equipment do taper crimp with the Lee Factory Crimp Die.
The following statement is from a reputable cast lead Vendor, how many agree with him? As per his website: Please do not use factory crimp dies for cast bullet reloading. Cast bullets MUST remain in their pristine state in order to shoot accurately. Factory Crimp Dies will decrease the cast bullet's sized diameter and thus will cause many unwanted issues. |
December 13, 2012, 04:12 PM | #2 |
Senior Member
Join Date: February 28, 2008
Location: Michigan
Posts: 2,619
|
Many of the older loading manuals and the long range shooters recomend shooting bullets in the same order as cast. In other words treat your cast bullets just like precision instruments, crimping will distort the bullet just as tumble lubing create's a bullet that will no longer shoot straight.
|
December 13, 2012, 04:27 PM | #3 |
Senior Member
Join Date: November 22, 2006
Posts: 3,077
|
I use the FCD with cast. Once you have everything set up just pull one finished round and compare with an untouched bullet. If they are the same, your good to go.
|
December 13, 2012, 04:38 PM | #4 |
Senior Member
Join Date: December 27, 2006
Location: Wisconsin
Posts: 1,475
|
I put a "light" taper crimp, enough to snug up and eliminate the minimal flare of the mouth that I set to allow for seating with no lead shaving.
I'm not being critical of this persons expertise, but feel following the Lee instructions has worked fine for me over time. I do know this person is not a fan of Lee equipment, and prefers Lyman dies. |
December 13, 2012, 05:00 PM | #5 |
Senior Member
Join Date: December 3, 2011
Posts: 558
|
As I have discussed on several threads, I agree, an FCD is perfectly fine for use with cast bullets. Due to loose tolerances at Lee, some people will have tighter FCDs than others. Mine .45acp fcd is a little tight and swages my .452" cast bullets by .0005"-.001". You can see a little ledge at the case mouth when you pull a bullet and the OD of bullet that was inside the case is slightly less than the exposed portion). In .380/9mm/.38/.357 this doesnt happen with the fcds I have
If there is any effect on accuracy I cant tell. Out of an SR1911 I shoot sub-2" groups at 25yds and cant come close to that with any other caliber handgun I load for. |
December 13, 2012, 05:07 PM | #6 |
Senior Member
Join Date: December 27, 2006
Location: Wisconsin
Posts: 1,475
|
I'm jealous, Nice Groups! Shooting offhand at 25 yards?
|
December 13, 2012, 05:15 PM | #7 |
Senior Member
Join Date: February 28, 2008
Location: Michigan
Posts: 2,619
|
Let's see every body does thing there own way, whitch I hope works for them.
But I would take the bullet manufacture's recomenditions, after all they made the bullet and chances are they tested it. |
December 13, 2012, 06:00 PM | #8 |
Senior Member
Join Date: December 3, 2011
Posts: 558
|
Oh heck no ShootingNut, I have no where near the skills for that! Seated, wrist supported on a small bag. I got one 5-shot group down to 1.5" but usually 1.75" is the best I can do. Needless to say I am very happy with both the SR1911 and that particular load (200gr hardcast SWC bullets are from reloadsnmore.com)
I was going to grind out the FCD or get another one to see if was a tad bigger but I just dont have the heart to mess with that setup. It requires a bit of force going into and out of the FCD (nothing really hard, about what a bulge buster would feel like). One more thing that I like to mention when this topic comes up- this .0005"-.001" swaging happens with every headstamp I use except R&P (Win, FC, PMC, Blazer all do it). Cartridges using R&P brass slide into and out of the FCD without any post sizing at all. Just one more indication that those who feel like R&P brass is thinner than most other brass (at least in .45acp) are correct. |
December 13, 2012, 06:05 PM | #9 |
Senior Member
Join Date: January 8, 2008
Posts: 803
|
A light taper does no harm, especially if you use it to basically remove any vestige of flaring and ensure that the case mouth is within spec.
I could see his view if you were putting a hell of a crimp and actually deforming the projectile, but if that were the case you'd also find yourself with some chambering issues because the round headspaces on the mouth of the case as it is. |
December 13, 2012, 06:34 PM | #10 |
Member
Join Date: October 28, 2012
Location: PA
Posts: 47
|
I use the Lee fcd with cast bullets for my 9 millimeter , Ruger sr9c with a 3.5 inch barrel . I'm using 4.3 grains, with a 115 grain bullet and a 1.115 to 1.120 oal. my flair the mouth of the case enough to not cause shaving when the bullet is seated.I crimp it enough where I get a mild ledge or impression in the cast bullet. Last Monday , I was able to hit 8 out of 10 rounds on a small paper plates at 25 yards . One hit the edge of the plate and the rest group within 4 inches . Luck on my part but you can't argue with the accuracy . At one point , I was concerned about the cast seams affecting the accuracy . I think that all these factors may play a minimal part . if you get the right combination of oal, grains, crimp ,case mouth flair , gun and Gun user the crimp die is a small factor .
|
December 13, 2012, 06:37 PM | #11 |
Senior Member
Join Date: May 12, 2011
Location: New Mexico
Posts: 1,315
|
+1 schmell, word for word
|
December 13, 2012, 06:48 PM | #12 |
Senior Member
Join Date: June 4, 2006
Location: West Virginia
Posts: 2,258
|
He is not talking about the crimp, he is trying to imply that the post sizing ring will squish the bullet deforming it. In my experience he is still wrong. I have never had one of my cast bullets get post sized in a FCD.
__________________
I don't ever remember being absent minded. |
December 13, 2012, 06:58 PM | #13 |
Senior Member
Join Date: December 27, 2006
Location: Wisconsin
Posts: 1,475
|
Crusty
Hi, I believe that you and I exchanged some reloading thoughts quite some time ago. I always appreciated your advice, glad to see your still in it. I relied very much on TFL forum when I first started loading with my Lee equipment, drawing on the experience of others. SN |
December 13, 2012, 07:14 PM | #14 |
Senior Member
Join Date: June 4, 2006
Location: West Virginia
Posts: 2,258
|
Thanks ShootingNut.
I'll admit the FCD isn't good for every situation but to say never use it with cast bullets is just wrong.
__________________
I don't ever remember being absent minded. |
December 13, 2012, 07:35 PM | #15 | |
Senior Member
Join Date: December 3, 2011
Posts: 558
|
Quote:
Here is a pic of an assembled cartridge (note the sharpie mark rubbed off by the post sizing ring). In the middle is a fresh bullet, on the bottom is a pulled bullet, showing the swaged portion (the swage extends to the base of the bullet. Crimp is .470" max. Perhaps rather than doubt me in the future you might consider that I do not make statements unless I have the facts to back them up. I extend this courtesy to you already. |
|
December 13, 2012, 08:00 PM | #16 |
Senior Member
Join Date: January 27, 2010
Location: AR
Posts: 1,401
|
In automatics, I have never TC'd cast bullets. Mainly because I seldom use cast bullets. Since autos headspace on the rim I would not feel safe crimping the case lip into the bullet or a canelure. One exception would be a revolver with moon clips.
Revolvers are a different story as crimping is a must. |
December 13, 2012, 08:04 PM | #17 | ||
Senior Member
Join Date: June 4, 2006
Location: West Virginia
Posts: 2,258
|
Quote:
Quote:
__________________
I don't ever remember being absent minded. Last edited by CrustyFN; December 13, 2012 at 08:17 PM. |
||
December 13, 2012, 08:16 PM | #18 |
Senior Member
Join Date: December 3, 2011
Posts: 558
|
Crusty- there is no problem with your FCDs. As there are no problems with all my other FCDs. However, you DID say I was wrong (see your previous post), but thats fine, I am a big boy (plus I like your posts so I will let it go!) but the fact is, Lee ships FCDs of various diameters. It took me a while to realize that mine is tight.
I went back to the original thread that caused me to measure my FCD and I see that you were a part of the discussion. Maybe you remember it? As discussed there, my FCD measures .4715", which of course could not accept a .452" bullet in a .010" wall case without swaging it. We can agree on that of course. To the OPs question, yes, you can use an FCD with cast bullets, but be aware, not all FCDs are created the same, and the one you have could contact the case and perhaps even slightly swage the bullet. If there is any disagreement with the above, lets discuss. There is more than enough FCD disinformation out there and at least on this forum we should be able to keep things straight amongst ourselves, agreed? |
December 13, 2012, 08:25 PM | #19 | |||
Senior Member
Join Date: June 4, 2006
Location: West Virginia
Posts: 2,258
|
Quote:
Quote:
Quote:
__________________
I don't ever remember being absent minded. |
|||
December 13, 2012, 08:41 PM | #20 | |
Senior Member
Join Date: December 3, 2011
Posts: 558
|
Quote:
I do think we are in agreement on the basic premise of this thread. Heck. I probably use my FCDs more than I need to but so far I havent found a reason not to. Thats one of the things I like about the LCT, that 4th station makes it as easy to use one as not. |
|
December 13, 2012, 09:08 PM | #21 |
Junior member
Join Date: November 12, 2000
Location: Colorado Springs, Colorado
Posts: 9,494
|
In my experience, the post sizing ring does deform or otherwise destroy my cast boolit (i.e. size) and I would not personally recommend them to anyone. I suppose it actually would depend on what size your cast boolits are, and what size the Lee FCD post sizing ring is, in the inside diameter.
From what I hear, Lee is not consistent in the sizing ring inner diameter, and this could explain why some say that the sizing ring does not size their boolits. I have only tried the one FCD in 44 cal., so that is hardly a representative amount of use to draw a positive conclusion from. I do like the crimp it applies so I simply popped out the sizing ring with a punch. That is enough for me to want to stay away from them, but that is a personal decision for me alone. |
December 13, 2012, 09:10 PM | #22 | |
Senior Member
Join Date: June 4, 2006
Location: West Virginia
Posts: 2,258
|
Quote:
__________________
I don't ever remember being absent minded. |
|
December 13, 2012, 09:19 PM | #23 |
Senior Member
Join Date: March 12, 2012
Location: Land of Enchantment
Posts: 436
|
The Lee FCDs that have a carbide ring at the base could reform/resize a lead bullet.
The ones without the carbide ring should be fine. The one I have for my 40 S&W has a carbide ring - irons out the "glock bulge." The two I have for my 45-70 and 30-30 rifles do not have a carbide ring and they're fine with cast bullets. |
December 13, 2012, 09:33 PM | #24 | |
Senior Member
Join Date: June 4, 2006
Location: West Virginia
Posts: 2,258
|
Quote:
__________________
I don't ever remember being absent minded. |
|
December 13, 2012, 09:36 PM | #25 |
Senior Member
Join Date: December 3, 2011
Posts: 558
|
Cool. Yeah, thats what gets me about my .45 fcd, all my others never touch anything. You know what, I am going to do what I said I was going to do before, order another .45 FCD and measure it, if it measures .472+, I will use it for my cast bullets and reserve my other for fmj only. As much as I love the results I hate the strain the tight fcd puts on my elbow round after round. I much prefer a FCD that touches only the very few cases that have issues.
Last edited by tkglazie; December 13, 2012 at 09:41 PM. |
|
|