The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Harley Nolden Memorial Institute for Firearms Research

Reply
 
Thread Tools Search this Thread
Old July 23, 2012, 08:05 PM   #1
Sisilija 55
Junior Member
 
Join Date: April 21, 2012
Location: OHIO
Posts: 8
Colt -revolver what is it???

Colt -revolver what is it??? Top of the barrel it says Colt's PT F A mfg co hartford ct patent aug 5 1884. Nov 6 88 mar 5 95

on the side of the barrel colt D A 38 matching serial numbers K7523

cylinder has the initials r.a.c.

Left side of gun has 2 sets of initials r.a.c.behind hammer. Above the wood grip has l.e.b.

6 shot cylinder ..small chip in the wood grip see attached photos any help would be appreciated.. I have more pictures I can send..
Attached Images
File Type: jpg 100_2967.JPG (161.7 KB, 254 views)
File Type: jpg 100_2970.JPG (195.7 KB, 164 views)
Sisilija 55 is offline  
Old July 23, 2012, 09:29 PM   #2
Webleymkv
Senior Member
 
Join Date: July 20, 2005
Location: Indiana
Posts: 10,446
Just a guess, but probably either a New Army or New Navy in .38 Long Colt. That was the standard issue U.S. Military handgun through the Spanish-American War and Philippine Insurrection and was replaced with the Colt Model 1909 New Service in .45 Long Colt and subsequently the M1911 in .45 ACP due to dissatisfaction with the performance of the .38 Long Colt Cartridge against Moro Tribesmen in the Philippines.
Webleymkv is offline  
Old July 23, 2012, 09:41 PM   #3
James K
Member In Memoriam
 
Join Date: March 17, 1999
Posts: 24,383
It is an Army Model of 1894 that has been heavily buffed and badly reblued and had later Colt wood grips installed instead of the uncheckered military grips. Those guns are rather fragile and give quite a bit of trouble when subjected to use. Further, parts are scarce and few (if any) gunsmiths today understand them. That model was chambered for .38 Long Colt and should NOT be fired with .38 Special, even if the longer cartridge will fit.

RAC is Army inspector Rinaldo A. Carr; LEB is Leroy E. Briggs, another Army inspector.

K7523 is not the serial number, it is an assembly number. The serial number should be on the bottom of the grip, along with the legend:
U.S.
ARMY
MODEL
1894
NO
xx
xxx

If that number is not there, it has been removed and the gun is illegal to own.

Those guns originally had no lanyard loop, but many were updated to include one.

Jim
James K is offline  
Old July 23, 2012, 11:00 PM   #4
Sisilija 55
Junior Member
 
Join Date: April 21, 2012
Location: OHIO
Posts: 8
Bottom of grip marked U.S. ARMY 1901 No.7523
Sisilija 55 is offline  
Old July 23, 2012, 11:24 PM   #5
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 21,825
What Jim K says. It's a New DA Army Revolver. It's on pages 241-242 of James Serven's Colt Firearms
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is offline  
Old July 24, 2012, 07:42 PM   #6
James K
Member In Memoriam
 
Join Date: March 17, 1999
Posts: 24,383
My bad, and I apologize. It is a Model 1901, not a Model 1894. The other information is correct.

But the butt marking should include the word "MODEL" and a Model 1901 should have a serial number in the 166xxx - 199xxx range on the butt in two lines. Could you show a picture of the butt marking?

Jim
James K is offline  
Old July 31, 2012, 10:09 AM   #7
Sisilija 55
Junior Member
 
Join Date: April 21, 2012
Location: OHIO
Posts: 8
pictures of the bottom...
Attached Images
File Type: jpg 100_3030.JPG (83.5 KB, 118 views)
File Type: jpg 100_3031.JPG (111.4 KB, 92 views)
Sisilija 55 is offline  
Old August 1, 2012, 11:32 AM   #8
James K
Member In Memoriam
 
Join Date: March 17, 1999
Posts: 24,383
Those are pretty poor pictures, but they seem to bear out what you said. The problem is that the Model 1901 should not have a four digit serial number (numbers were in the 166xxx - 199xxx range and were always stamped on the butt in two rows of three numbers each.

I would like to see better and closeup pictures of that butt marking; there is something odd with that gun.

Jim
James K is offline  
Old August 1, 2012, 06:49 PM   #9
Dfariswheel
Senior Member
 
Join Date: May 4, 2001
Posts: 7,478
The numbers have been re-stamped, and done by hand. Note the irregular spacing and line.
Dfariswheel is offline  
Old August 1, 2012, 07:59 PM   #10
James K
Member In Memoriam
 
Join Date: March 17, 1999
Posts: 24,383
I suspect that someone, many years ago, maybe filed the serial number off that gun. Then maybe someone else, possibly aware of the penalty for possession of a gun with the serial number removed, used the assembly number to "restore" the serial number. Maybe not "kosher" but the old gun has a serial number and that is what is important. (It is a sort of a matter of opinion if it is the number it had originally.) Nuff sed.

Jim
James K is offline  
Old August 3, 2012, 11:17 AM   #11
Sisilija 55
Junior Member
 
Join Date: April 21, 2012
Location: OHIO
Posts: 8
Gone back to owner

Last edited by Sisilija 55; August 5, 2012 at 12:28 AM.
Sisilija 55 is offline  
Old August 20, 2012, 11:19 AM   #12
Sisilija 55
Junior Member
 
Join Date: April 21, 2012
Location: OHIO
Posts: 8
I THINK THERE ARE MORE 4 DIGIT SER. # OUTSIDE THE published serial number ranges. I've saw another K prefix 3 AND 4 digit number on several of the auction sites...
I found this on the:
Springfield Armory Museum - Collection Record

Title: REVOLVER - COLT REVOLVER MODEL 1901 DA ARMY .38 SN# 2364
Maker/Manufacturer: COLT
Date of Manufacture: 1901-1907
Eminent Figure:
Catalog Number: SPAR 1885
Measurements: OL: 30.4CM 12" BL: 15.2CM 6"


Object Description:

COLT REVOLVER MODEL 1901 DA ARMY .38 SN# 2364
Manufactured by Colt, Hartford, Ct. - Standard 6-shot DA Model 1901 Army revolver with swing-out cylinder and smooth walnut grips. Blued finish. Weapon identical to the M1896 except for addition of an oblong lanyard swivel at the butt. Blade steel front, rear sight cut into frame.

Markings:
Barrel: COLT'S PT. F.A. MFG. CO., HARTFORD CT. U.S.A./PATENTED AUG. 5, 1884, NOV. 6, 88, MAR. 5, 95. (Left): COLT D.A. 38.
Cylinder latch: K/2364
Buttstrap: U.S./ARMY/MODEL/1901/2364.
Grips: RAC
Frame: RAC & L.E.B. Indicates a Remington rework for home guard. 3/2364. RAC = Rinaldo A. Carr. LEB = Leroy E. Briggs.
Cylinder yoke: Z 2364.

Notes: "Special Report of New Work undertaken and New Supplies issued for Service. #46. April 1, 1902....SUGGESTION THAT CYLINDER OF REGULATION REVOLVER OPEN TO THE RIGHT. There was originally a diversity of opinion among Cavalry officers as to which was the better method, the right or left hand opening, but in 1894 it was decided that the cylinder should open to the left, as it was considered that by opening as it now does it allows the use of the right hand in throwing out the cylinder and replacing it." O.O. Letter No. 38078-7.
Sisilija 55 is offline  
Old August 20, 2012, 12:02 PM   #13
Chuckusaret
Junior member
 
Join Date: December 5, 2008
Location: Florida
Posts: 708
Check out proofhouse.com

Last edited by Chuckusaret; August 20, 2012 at 12:09 PM.
Chuckusaret is offline  
Old August 20, 2012, 04:14 PM   #14
James K
Member In Memoriam
 
Join Date: March 17, 1999
Posts: 24,383
Two things cause confusion with those guns. One is the presence of the assembly number, which is quite prominent and often taken for the serial number, even when the serial number is present. That can lead to errors in record keeping.

The other is what I mentioned, that military personnel sometimes "liberated" their guns (Shock!! Hhorror!! Would our gallant soldiers do that???) and ground or filed the butt markings and true serial number off. That left only the assembly number, and sometimes that was used to replace the serial number on the butt.

FWIW, I have seen two of those guns with the butt marking removed, so I have to think it was a fairly common practice.

Jim
James K is offline  
Old August 21, 2012, 09:39 AM   #15
jerry12p
Junior Member
 
Join Date: August 21, 2012
Posts: 3
Colt Officers Model Target 38 Special CTG

Can anyone help me with value and vintage of this Colt Officers Model Target 38 , SN 780XXX with an 8 under the SN? I purchased from my uncle recently, and he thought it was a S&W. I looked last evening and saw it is Colt, with identification mentioned. I appreciate any help. Looking for when it was made how much worth, any history...it is in very good shape, no nicks. Plastic handles.
jerry12p is offline  
Old August 23, 2012, 11:09 AM   #16
Chuckusaret
Junior member
 
Join Date: December 5, 2008
Location: Florida
Posts: 708
I have had good luck on colt forums getting info and the colt site.

Last edited by Chuckusaret; August 23, 2012 at 11:15 AM.
Chuckusaret is offline  
Old August 23, 2012, 02:03 PM   #17
James K
Member In Memoriam
 
Join Date: March 17, 1999
Posts: 24,383
Serial numbers on those guns are confusing, to say the least, but as far as I can tell, that gun was made in 1950. No way to tell value without good pictures.

(The "8" under the serial is an inspection mark, not part of the serial number.)

Jim
James K is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:01 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.06996 seconds with 11 queries