The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Competition Shooting

Reply
 
Thread Tools Search this Thread
Old February 29, 2012, 06:43 PM   #1
Rockdriller
Member
 
Join Date: April 29, 2011
Posts: 21
.45 acp Loads for Steel plate Competition,

Hello folks,
I am going to shoot in my first shooting competition soon and its going to be a 6 stage steel plate setup. I am thinking of using either my .45 sig 1911 or my glock 35 in .40 smith. I have never shot in any comp before so I have no idea what to load for ammo.
I have most standard handgun powder and access to whatever bullets powder combo I need.
I was wondering what you serious steel shooters on "The Firing Line" shoot for loads.
Thanks for any info
Rockdriller is offline  
Old February 29, 2012, 09:22 PM   #2
PawPaw
Senior Member
 
Join Date: December 24, 2010
Location: Central Louisiana
Posts: 3,137
Quote:
I was wondering what you serious steel shooters on "The Firing Line" shoot for loads.
I'm not a serious steel shooter, but my go-to load for the .45 ACP is 4.6 grains of Bullseye under a 230 lead bullet. Flat point, round nose, take your choice. Range brass, anybody's primer. It gives me 900 fps from my 5" 1911 and is plenty good for any steel plate I might encounter.
__________________
Dennis Dezendorf

http://pawpawshouse.blogspot.com
PawPaw is offline  
Old March 1, 2012, 12:09 AM   #3
g.willikers
Senior Member
 
Join Date: September 28, 2008
Posts: 10,442
You definitely want to use only lead bullets.
Most matches using steel targets will only allow lead, due to the dangers of copper jacket ricochet.
200 grain swc at ~850f/s for steel works very well and is a popular steel target load.
Fast recoil recovery time and very effective.
__________________
Walt Kelly, alias Pogo, sez:
“Don't take life so serious, son, it ain't nohow permanent.”
g.willikers is offline  
Old March 1, 2012, 12:17 AM   #4
lmccrock
Senior Member
 
Join Date: April 23, 2007
Location: Red Rock. TX
Posts: 820
Steel Challenge, or falling steel? Steel Challenge basically requires the plate to go "ding" but it does not fall. Falling steel like (like USPSA or others) require the plate to fall, so a minimum amount of oomph is required. For USPSA, I shoot a 45acp 230gr lead or coated bullet around 740fps. For Steel Challenge-type matches, same bullet at 700-ish. Small amount of fast powder like Clays or Titegroup makes it shoot pretty soft.

Regardless, shoot whichever gun is faster for you. Might take a couple matches to sort that out.

Every match I go to allows jacketed bullets on steel; better ask the match director.

Last edited by lmccrock; March 1, 2012 at 12:20 AM. Reason: Comment on jacketed ammo
lmccrock is offline  
Old March 1, 2012, 12:31 PM   #5
kraigwy
Senior Member
 
Join Date: June 16, 2008
Location: Wyoming
Posts: 11,061
I use 3.8 gr. of Bullseye pushing a 225 gr cast RN bullet.

Never hit a plate that didn't fall.

I also use it in Bullseye matches. It works for me.

Easy on the gun and shooter if you're shooting 100 plus rounds per session.
__________________
Kraig Stuart
CPT USAR Ret
USAMU Sniper School
Distinguished Rifle Badge 1071
kraigwy is offline  
Old March 1, 2012, 01:53 PM   #6
PawPaw
Senior Member
 
Join Date: December 24, 2010
Location: Central Louisiana
Posts: 3,137
Quote:
Originally Posted by kraigwy
I use 3.8 gr. of Bullseye pushing a 225 gr cast RN bullet.
Really? With a charge that light, do you have any trouble with the 1911 cycling?
__________________
Dennis Dezendorf

http://pawpawshouse.blogspot.com
PawPaw is offline  
Old March 1, 2012, 02:00 PM   #7
kraigwy
Senior Member
 
Join Date: June 16, 2008
Location: Wyoming
Posts: 11,061
No sir, it functions perfectly in both my 1911a1 (unmodified) and Series 70 Gold Cup.

I got that load from an late 70s NRA article on Bullseye shooting. Been using it every since.

It's mild but has the mass to knock down any plates I've ever hit.

Being mild also makes it easy and faster to stay on or move to the next target.
__________________
Kraig Stuart
CPT USAR Ret
USAMU Sniper School
Distinguished Rifle Badge 1071
kraigwy is offline  
Old March 1, 2012, 02:26 PM   #8
PawPaw
Senior Member
 
Join Date: December 24, 2010
Location: Central Louisiana
Posts: 3,137
Hmmm! I've learned something today.

Thanks, Kraig, I'll have to try it in my autoloaders.
__________________
Dennis Dezendorf

http://pawpawshouse.blogspot.com
PawPaw is offline  
Old March 1, 2012, 05:17 PM   #9
sam colt
Member
 
Join Date: February 11, 2012
Location: nc
Posts: 93
you've got to remember Gold Cups come with a 14lb recoil spring.
sam colt is offline  
Old March 2, 2012, 01:24 AM   #10
chris in va
Senior Member
 
Join Date: December 26, 2004
Location: Louisville KY
Posts: 13,805
I use 4.7gr of Universal with my 45 LRN in IDPA. The brass practically falls at my feet and I can see the bullet in flight on a sunny day.
chris in va is offline  
Old March 2, 2012, 03:52 PM   #11
Don P
Senior Member
 
Join Date: December 17, 2005
Location: Swamp dweller
Posts: 6,187
Personally I do not load for any given discipline. I load them so the gun functions and from chronoing loads I meet or exceed power factor
__________________
NRA Life Member, NRA Chief Range Safety Officer, NRA Certified Pistol Instructor,, USPSA & Steel Challange NROI Range Officer,
ICORE Range Officer,
,MAG 40 Graduate
As you are, I once was, As I am, You will be.
Don P is offline  
Old March 2, 2012, 05:02 PM   #12
Steviewonder1
Senior Member
 
Join Date: February 16, 2009
Location: John's Creek, Georgia
Posts: 328
In my G-35 I load 200Gr Copper Wash (Lead Underneath) over 5.1 Gr of Unique. Makes major for IPSC and functions the gun very well. YMMV as this works and has been tested only in my gun.
Steviewonder1 is offline  
Old March 6, 2012, 11:07 AM   #13
Rockdriller
Member
 
Join Date: April 29, 2011
Posts: 21
Thanks for all the tips guys. The Firing Line has always been the best source of info. I loaded up 500 230gr lead round nose in mixed brass with cci primers and 4.5 of bullseye. I was told this is six stages of 35 plates in each and they have to fall off the holders.
Practice has been a lot of fun. Its too bad so mmany anti-gunners hace no idea how FN awesome it feels to blast a wall of steel. Oh well more range time for us!!!!!!
Rockdriller is offline  
Old March 10, 2012, 04:48 PM   #14
PawPaw
Senior Member
 
Join Date: December 24, 2010
Location: Central Louisiana
Posts: 3,137
Quote:
Originally Posted by kraigwy
I use 3.8 gr. of Bullseye pushing a 225 gr cast RN bullet.
I loaded a box of those and took them to the range today. My wife is practicing for her CCW class and I took those along in the off chance that I got to shoot my 1911. After she was finished, I hung a target and ran it out to the 5 yard line.

Nice. Not as much recoil, very controllable, functioned my Kimber just fine. Accurate? Oh, yeah, I can see that this is going to be my go-to load for plinking and target shooting with the .45 ACP. Thanks, Kraig!
__________________
Dennis Dezendorf

http://pawpawshouse.blogspot.com
PawPaw is offline  
Old March 11, 2012, 09:40 PM   #15
Nnobby45
Senior Member
 
Join Date: November 20, 2004
Posts: 3,150
When .45ACP was king of IPSC, 5.7 or 5.8 gr. of W231 made "major" caliber with the 200 gr. SWC. Light loads would use from 5.0 to 5.2 gr. Maybe less if you change the recoil spring.

Bullseye and W231 were the two most popular powders, I believe.
Jeff Cooper had a favorite load using IMR 700X.

My preference is 200 SWC with 5.6 gr. W231. Enough recoil so you know you're shooting a .45 and easy to shoot all day long if you want.

For 230 plated or jacketed, I prefer 5.7 gr. of W231. This load approximates the velocity of WWB, at about 770 fps from a 5" bbl. Easy to shoot, but not whimpy. My steel plate shooting is on my own Evil Roy Portable Tgts. Not formal competition. A good hardball equivilent might be 5.8 or 5.9 gr. W231 with 230 gr. Jacketed hardball. When I use Winchester JHP, they develop more pressure and I reduce the load to about 5.6 or 5.7 gr.
Nnobby45 is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:59 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.10619 seconds with 10 queries