|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
July 28, 2011, 12:53 PM | #1 |
Member
Join Date: July 28, 2011
Location: Churchs Ferry, ND
Posts: 70
|
New to reloading guidence needed
im new to reloading and to this forum and want to start reloading .223's for my AR15 and looking for a set up that will work best for target/coyote shooting/hunting. ive done some reading in my lymans 49th addition and a few ppl on line say they like the H335 or varget powder.
here is my set up DPMS 20" bull barrel with a 1-9" twist this will be my 1st time reloading and i bought a lee 3stage turret press with double disk kit. i have the gun sighted in with 55gr bullets right now. any more input would be appreciated. Last edited by ryans01z28; July 28, 2011 at 01:22 PM. |
July 28, 2011, 01:38 PM | #2 |
Senior Member
Join Date: December 30, 2009
Location: Maryland
Posts: 124
|
Well your in the right place and asking good questions.
The first thing some of the group would suggest is to read all the stickies, this is all the info that will get you started.
Now You should read all of the reloading manual, and the others that are suggested. Here's my input to your new project. Assuming you already have the materials you need, this is powder, primers, brass, bullets. And the correct dies for your Lee turrett. Decap and resize. the brass, even if new brass, I'd go ahead and resize. You will figure that out all by your self. You will need to lube the cases, so they don't get stuck in the die. Then you clean the lube off, several methods used. Another thing to learn. reprime, either on the press or by a hand tool. add your powder load. You best have a scale to check your powder drops. seat your bullet. To the recommended COAL. crimp your bullet. Recommended for an autoloader. Only crimp to keep the bullets from moving around. You can get a zillion responses for this topic, try the KISS principle. Read the book. Now I drop my resized cases in a chamber guage and then again after loading a few to check my settings, this is a good tool, less than 20$. Get one. record your load, in a notebook, Notebooks don't need batteries, and never remove a page from this notebook. try out your loads and see how they do. Good luck and stay safe. Duane USN/ret Reloading with Blu/Red/Grn/Ora |
July 28, 2011, 01:46 PM | #3 |
Member
Join Date: July 28, 2011
Location: Churchs Ferry, ND
Posts: 70
|
My question did not say how do I reload 223s but what powder did ppl found to be the best match for target and coyote hunting, and as stated in my 1st post I have a lyman 49th addition that I've been reading. I have no power no bullets no nothing right now. I'm waiting for my press with dies to arive and the only other thing I have is a tumbler other than that I'm in the dark still
Just to make it a little easer 4some ppl what recipe are you using with a 55grain bullet? Is it a boat tail bullet exct. exct. Last edited by ryans01z28; July 28, 2011 at 02:10 PM. |
July 28, 2011, 02:09 PM | #4 |
Senior Member
Join Date: December 24, 2010
Location: Central Louisiana
Posts: 3,137
|
There are lots of good powders for .223, you just have to find one that suits you. I like IMR 4895, but I've been using it for several decades and every rifle caliber I have has at least one 4895 recipe. But, there are lots of other powders that work just as well, or better than mine. Depending on your rifle.
You see, handloading is really dependent on your rifle. What your rifle likes. The only way you're going to know that is by testing. There are literally a dozen or more good powders for the .223, and people are loathe to give recipes because there are so many potential variations. The biggest question is: which powders can you find locally to use? Look in your manual and find the .223 recipe page. Then, find the recipes with 55 grain bullets, then make note of the powders that give the best velocity. Then, look around and see if you can find those powders locally. That's the powder you will use for testing. |
July 28, 2011, 02:09 PM | #5 |
Junior member
Join Date: May 16, 2009
Location: Central Texas
Posts: 1,343
|
What powder does your lyman suggest?
|
July 28, 2011, 02:21 PM | #6 |
Member
Join Date: July 28, 2011
Location: Churchs Ferry, ND
Posts: 70
|
The best powder lyman suggested was varget at number 1 but had about 15 other powders also. I heard H322 was good but wasn't on lymans list. I found H322 at this sporting store that's going out of business for $19 +tax per pound but didn't buy it till I knew 4sure I could use it
|
July 28, 2011, 02:42 PM | #7 |
Senior Member
Join Date: February 21, 2002
Location: Transplanted from Montana
Posts: 2,311
|
ryans01z28
First and foremost WELCOME TO TFL! There are many powders which will give excellent accuracy in the 223. Your weapon will have it’s own likes and dislikes. And may like entirely different powder/bullet combinations than an identical rifle. Bottom line - - - you will just have to test several. The twist of your barrel will dictate the use of certain weight bullets. You should know what your twist rate is before going further. My recommendations for a 55 gr bullet would be to try Varget and TAC as starters. If neither works well, try BL-C2 and either IMR 4895 or H4895. I have not tried the newer powders Benchmark or IMR 8208 XBR . Below is a listing of a few factors I have come across which affect accuracy. Other folks have published articles and books on these categories. Primer: strength, brisance - is a measure of the rapidity with which an explosive develops its maximum pressure Barrel: length; tightness of bore; height of the lands; distance of bullet to lands; temperature of barrel; Lock Strength: the force which is applied to the primer by various strength firing mechanisms; Bullet: bearing surface of bullet, alloy of bullet; shape of bullet; distance off rifling; Brass: new/used elasticity; manufacturer, volume; crimp; Powder: new, aged, old, batch powder was from; Weather: ambient air temp., barometric pressure, humidity Elevation: above sea level Other: I am sure I have not listed all Good Shooting!
__________________
I pledge allegiance to the Flag - - -, and to the Republic for which it stands….Our Forefathers were brilliant for giving us a Republic, not a democracy! Do you know the difference??? and WHY?http://www.wallbuilders.com/LIBissue...les.asp?id=111 |
July 28, 2011, 03:54 PM | #8 |
Senior Member
Join Date: April 23, 2008
Location: Medina, Ohio
Posts: 273
|
This has worked for me for many years in AR's and Mini=14's:
LC brass CCI SR primers H335 (follow load manual recommendations) Hornady 55 gr JSP (can use their FMJ as well) I do not crimp YMMV
__________________
God Bless America US Army, NRA Endowment TSRA Life, SASS |
July 28, 2011, 09:54 PM | #9 |
Senior Member
Join Date: February 21, 2002
Location: Transplanted from Montana
Posts: 2,311
|
ryans01z28
Instead of editing your original post, it is less confusing for readers if you add a new post answering the questions. Since you have a 9 twist, you should consider a heavier bullet. The 9 twist is ideal for 65 thru 75 grain bullets. Some weapons will stabilize the 55 and produce OK groups. However, when loaded to it’s potential with the heavier bullet, you will get noticeably better groups, especially at/beyond 200 yards, especially in a wind. My choice would be the Sierra 69 HPBT. Good Shooting!
__________________
I pledge allegiance to the Flag - - -, and to the Republic for which it stands….Our Forefathers were brilliant for giving us a Republic, not a democracy! Do you know the difference??? and WHY?http://www.wallbuilders.com/LIBissue...les.asp?id=111 |
July 28, 2011, 11:07 PM | #10 |
Member
Join Date: July 28, 2011
Location: Churchs Ferry, ND
Posts: 70
|
i see, well maybe ill try a 65 gain bullet. i was shooting my 55 grain out to 300yds with consistent groups all were within 1/2" to 1" of each other which i thought was pretty good. i was wondering still if it would be good to pick up some of the H322 since it was discounted to $19+ tax. im heading back to my other home this wknd and want to pick it up if they still have it. can i use the H322 with a 55 or 65 grain bullet and get good performance?
|
July 28, 2011, 11:14 PM | #11 |
Junior member
Join Date: November 12, 2000
Location: Colorado Springs, Colorado
Posts: 9,494
|
Actually, reloading for your AR15 is a little more cut and dried than for other calibers. For instance, there's only two primers you should be using and positively do not use others. You want to use Rem 7-1/2's or the CCI Mil-Spec primer (#41?).
Powders I've had good results with IMR-4064 BLC-2 IMR-4895 H-335 RL-15 |
July 28, 2011, 11:17 PM | #12 |
Member
Join Date: July 28, 2011
Location: Churchs Ferry, ND
Posts: 70
|
i have CCI primer number 400 small rifle primers, that was what the guy at the store said and thats what it said on his chart so hope that is write
|
July 28, 2011, 11:39 PM | #13 |
Junior member
Join Date: November 12, 2000
Location: Colorado Springs, Colorado
Posts: 9,494
|
I don't think that's them. The Mil-Spec primers have a thicker cup for the Mil-Spec rifles and if you use regular small rifle primers you risk piercing a primer.
|
July 28, 2011, 11:56 PM | #14 |
Member
Join Date: July 28, 2011
Location: Churchs Ferry, ND
Posts: 70
|
you gota be ****tin me... i looked at the chart my self and it said i need these primers. i bought 1000 of the things i hope your wrong cuz idk what im going to do with them if there wrong
|
July 29, 2011, 12:16 AM | #15 |
Senior Member
Join Date: July 5, 2007
Location: Pacific NW
Posts: 1,310
|
This chapter from an older Sierra reloading manual has the answers to a lot of your questions, and more information on top of that -
http://www.exteriorballistics.com/re...sgunreload.cfm I believe the danger from using too sensitive a primer is slam-fires rather than pierced primers. Pierced primers will damage your gun, but slam-fires have the potential to damage you, especially if it is out of battery. I also suggest you pay particular attention to full-length resizing. Good luck.
__________________
.30-06 Springfield: 100 yrs + and still going strong |
July 29, 2011, 12:50 AM | #16 |
Senior Member
Join Date: February 21, 2002
Location: Transplanted from Montana
Posts: 2,311
|
H332 will work in bullet weights from 40 to 80 grains. However, in several hundred 223 threads over the years, I do not recall anyone saying that their best accuracy was with that powder.
If you do not use the hard cup primers, sooner or later you will get a slam fire. CCI's are harder cup than most primers, but the CCI #41 are NATO Spec. And a general rule of thumb is to use magnum primers (CCI 450) with ball (spherical) powders.
__________________
I pledge allegiance to the Flag - - -, and to the Republic for which it stands….Our Forefathers were brilliant for giving us a Republic, not a democracy! Do you know the difference??? and WHY?http://www.wallbuilders.com/LIBissue...les.asp?id=111 Last edited by Shoney; July 29, 2011 at 12:55 AM. |
July 29, 2011, 09:22 AM | #17 |
Member
Join Date: July 28, 2011
Location: Churchs Ferry, ND
Posts: 70
|
So thoes are indeed the wrong primers 4shure is what your saying? I'm going to go back to that store this wkend and look at that chart to see what these primers are for because it showed these primers for 223s I'm 99% sure not sayin I don't believe u
|
July 29, 2011, 05:28 PM | #18 |
Member
Join Date: July 28, 2011
Location: Churchs Ferry, ND
Posts: 70
|
Well I just talked to a local guy that makes guns and I asked him what he thought about the primers and he said he would use the cci#400 in a heart beat. I also talked to him about powders and he of coarse said there's lots to chose from so I think I'm going to try the H322 since I have seen some testing done on that along with the H335.(Not heat sensitive)
|
July 29, 2011, 06:03 PM | #19 |
Senior Member
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,930
|
Ok I will help a bit. I have a 1 in 9 Savage bolt action that I load for. I also load for a several different AR rifles for friends.
Primer: (Have used CCI 400, Rem 7 and a half, an Winchester.) Make sure they are seated slightly below flush. Cases: Mixed Headstamps. Powder: Hodgdon H335 Bullet 55 grain Hornady V Max, and 55 grain Winchester FMJBT. All worked well with 25.0 grains of powder. (Note all rifles were tested with lighter loads prior to check for function, and pressure signs.) This load in my Savage Model 12 LRPV has not failed to drop coyotes out to 400 yards. (Farthest shot was 415 yards measured with a lazer range finder.)
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you. |
July 29, 2011, 06:06 PM | #20 |
Member
Join Date: July 28, 2011
Location: Churchs Ferry, ND
Posts: 70
|
That is the same recipe I was going to go with EXACTLY for my AR
|
July 29, 2011, 06:15 PM | #21 |
Senior Member
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,930
|
I would recomend a note of caution. Load some starting at 23.8 grains then go up in .3 grain increments to 25.0 to assure it is the load that particular rifle works well with.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you. |
July 29, 2011, 06:18 PM | #22 |
Member
Join Date: July 28, 2011
Location: Churchs Ferry, ND
Posts: 70
|
Yeah ur right on that. I wasn't going to go and load them that much right away
|
July 29, 2011, 11:23 PM | #23 |
Member
Join Date: July 28, 2011
Location: Churchs Ferry, ND
Posts: 70
|
Ohh I was going to ask, is there a way to set the primer tool up so it seats it just past flush?
|
July 30, 2011, 12:08 AM | #24 |
Junior member
Join Date: May 16, 2009
Location: Central Texas
Posts: 1,343
|
YOU HAVE SO MANY QUESTIONS AND NOT ENOUGH ANSWERS, You should read read and read some more. Know exactly how to reload before asking every Tom, Dick and Harry and still not knowing for sure how and what to do for sure!!!! Get your reloading manual, it should tell you everything you need to know
|
July 30, 2011, 12:10 AM | #25 | ||
Senior Member
Join Date: May 25, 1999
Location: Too close to Houston
Posts: 4,196
|
Quote:
My AR loads these days use Wolf SRM primers. I bought them because they have a harder cup than their SR primers and they weren't marketing the .223 primers at the time. Quote:
__________________
Proud member of the NRA and Texas State Rifle Association. Registered and active voter. |
||
Thread Tools | Search this Thread |
|
|