April 4, 2012, 07:39 PM | #1 |
Junior member
Join Date: April 4, 2012
Posts: 17
|
Remington 721 30.06
I was wondering, how do I go about replacing my bolt on my Remington 721 30.06?
|
April 4, 2012, 07:51 PM | #2 |
Senior Member
Join Date: February 10, 2010
Posts: 720
|
By replacing your bolt, to you mean to obtain a new one, or to re-insert it in the rifle?
|
April 4, 2012, 08:41 PM | #3 |
Member
Join Date: April 4, 2012
Posts: 17
|
He needs a new one. or at least a reputable source for replacement parts
|
April 4, 2012, 09:13 PM | #4 |
Junior member
Join Date: April 4, 2012
Posts: 17
|
Personally I have heard you can use a 700 model and it works just fine figured I would ask around. And stainless is right, I need the whole thing. Mine still works, the extractor is denting the rim on the back of the casings.
|
April 4, 2012, 10:09 PM | #5 |
Senior Member
Join Date: February 10, 2010
Posts: 720
|
you may be able to order one here, but they appear to be sold out right now:
http://www.gunpartscorp.com/catalog/...560&catid=4335 Otherwise I would contact remington to see about returning the rifle to them for repair. I am unsure about using a remington 700 bolt in a 721. It would be best in my view to contact remington direct and see what they advise. |
April 4, 2012, 10:18 PM | #6 |
Junior member
Join Date: April 4, 2012
Posts: 17
|
Thank you, i appreciate you insight on my problem. I love this gun, it was assembled in 1950 and to this day at 30 yards will remove the bulls eye from the target.
|
April 5, 2012, 12:25 AM | #7 |
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,832
|
Why not have the extractor replaced or adjusted?
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
April 5, 2012, 01:05 AM | #8 |
Junior member
Join Date: April 4, 2012
Posts: 17
|
I was told they don't make the part anymore? Can you tell me how to have it replaced?
|
April 5, 2012, 08:29 AM | #9 |
Senior Member
Join Date: April 8, 2009
Location: Batchelor, La.
Posts: 579
|
You've got extractor problems, take the thing to a competent 'smith and have it repaired. Replacing the bolt involves checking the headspace which may not be correct. Correction will involve either deepening the chamber or setting the barrel back and correcting the chamber. Either way you need a gunsmith and potentially spending a lot more money than just getting the extractor repaired. Here endeth the lesson. Goatwhiskers the Elder
|
April 5, 2012, 10:20 AM | #10 |
Senior Member
Join Date: March 5, 2009
Location: NY
Posts: 317
|
First determine if your extractor is retained by either 1 rivet type fastener or is it a newer style snap in w/no rivet and fairly easy to replace. In either case contact Rem. customer service and try to buy one (a gunshop might have to buy it for you). I don't believe it to be a restricted part. The bolt body is restricted. I would not send the whole gun back as there is a good chance they would keep it sending you a voucher as PARTIAL payment for a new rifle. The problem being that the 721 is obsolete and they (Rem.) want it out of circulation. This is what they did to my dad when he sent his 721 back to be rebarreled. I would try to buy the parts. Where are you located?
|
April 5, 2012, 10:34 AM | #11 |
Senior Member
Join Date: March 5, 2009
Location: NY
Posts: 317
|
I read your post again and got to the part about denting the rim. The extractor fits into a recess machined into the bolt. If there is enough crap BEHIND the extractor (in the cutout) it may not be allowing the extractor to move out of the way of the rim as the cartridge is chambered. Clean with an old tooth brush really good. With the bolt out of the rifle fit a case under the lip of the extractor and pivot it into the bolt. The extractor should move out of the way a tad allowing the case to seat against the bolt face. Just a thought.
|
April 5, 2012, 10:50 AM | #12 |
Junior member
Join Date: April 4, 2012
Posts: 17
|
I'm located in Davison, MI. The rifle is clean front to back, even the bolt. This is why I'm concerned. You can see the extractor is worn. I take real good care of this rifle, out of my three guns it is my favorite.
|
April 5, 2012, 12:07 PM | #13 |
Senior Member
Join Date: March 5, 2009
Location: NY
Posts: 317
|
I'm not saying the rifle isn't clean. You cannot see the recess into which the extractor fits and that is why I suggested a very thorough cleaning and pushing on the extractor to see if it would move into the recess. Attached are pictures of the old (L) style and the new (R) style extractors. Can you tell what you have? On the old style the rivet head would be visible on the inside wall adjacent to the bolt face. Can you take a good close up of your bolt face?
Last edited by tango1niner; April 18, 2018 at 10:05 AM. |
April 5, 2012, 12:45 PM | #14 |
Junior member
Join Date: April 4, 2012
Posts: 17
|
I don't think either one of those are like mine. Give me a minute and I'll pull my and send you a picture of it.
Last edited by OneForAll; April 5, 2012 at 12:58 PM. |
April 5, 2012, 01:12 PM | #15 |
Junior member
Join Date: April 4, 2012
Posts: 17
|
I think I figured it out, I didn't remove the extractor, and mine doesn't have a rivet holding it in. It's under spring tension and if I remove it it's not suppose to be put back in. I moved it around though and can noticeably feel a build up behind it. I 'm going to clean it real good and but another extractor from Brownells. I'll remove the old one then.
|
April 5, 2012, 04:05 PM | #16 |
Junior member
Join Date: April 4, 2012
Posts: 17
|
The first picture you posted the one on the right now all I need is to know where to get one?
|
April 5, 2012, 04:40 PM | #17 |
Junior member
Join Date: April 4, 2012
Posts: 17
|
I called Remington customer service inquiring about a new extractor and representative I spoke with told me "we don't carry anything for the 721 model, there is not compatible extractors, and that they won't even touch the gun", wow wonderful service.
|
April 5, 2012, 04:57 PM | #18 |
Member
Join Date: April 4, 2012
Posts: 17
|
That's the last straw for me. I wont buy anything remmington, not even ammo.
I reload, and the primers are often undersized too. |
April 5, 2012, 05:40 PM | #19 |
Senior Member
Join Date: September 16, 2009
Location: I live in the foot of the Green Mountains of Vermont
Posts: 1,602
|
Get Real !!
Come on guys , production of the model 721 stopped in 1961 for Christs sake . That was 51 years ago , how long do you expect Remington to stock parts for obsolete guns ? There are extractors out there , you just have to find them , instead of whining like little girls ! I have three in my inventory at the present time .
|
April 5, 2012, 05:53 PM | #20 |
Member
Join Date: April 4, 2012
Posts: 17
|
Compared to the customer service and warranty at Springfeild Armory, Remington looks like a fly by night Chinese internet company.
|
April 5, 2012, 05:58 PM | #21 |
Junior member
Join Date: April 4, 2012
Posts: 17
|
I didn't say much about Remington themselves, I didn't like the tone I was given when I spoke to the representative over the phone.
|
April 5, 2012, 11:18 PM | #22 |
Member
Join Date: March 5, 2012
Location: Idaho
Posts: 50
|
I ended up with dad's 721 after his passing. The thing that really worried me was the trigger/safety after doing some reading up on them. Had the trigger assy replaced and a zillion years of gunk cleaned out of it. And yes the bolt does have some wear, but has never let me down.
__________________
A vote is like a rifle; its usefulness depends upon the character of the user. Theodore Roosevelt |
April 5, 2012, 11:41 PM | #23 |
Member
Join Date: April 4, 2012
Posts: 17
|
Its a nice gun, OneForAll did a great job bringing it back up to standard. It had the wrong stock on it, now it is all black, with a new optic, and bipod. The thing looks great. Im not sure it was cleaned thoroughly until he got it.
Its just too bad that a company that can put together such a nice rifle doesnt do as good with its customers as it should. As far as discontinued parts go, in this day and age of computer aided design and manufacturing, there is no reason that a company, espacially a large one like remmington cant punch some numbers in a cad cam machine, and make a new extractor in a few minutes for a customer like this. |
April 6, 2012, 12:14 AM | #24 |
Junior member
Join Date: April 4, 2012
Posts: 17
|
I have done everything that I could possibly do to put this gun in its best working condition. I am hoping to come across a bolt extractor that does not cost $50.
|
April 6, 2012, 06:31 AM | #25 |
Senior Member
Join Date: July 18, 2010
Location: Independence Missouri
Posts: 4,585
|
Somewhere in the basement of that Remington factory probably sits a bag of those sucker's that a geezer like me had the foresight to put a few back, just in case,,,,, Sounds like Remington folk have become bit sirly, and lazy.!
That why Savage and Weatherby and Howa and Winchester and Marlin and.....should I keep going? outsell them. It sucks dude but your going to have to keep an eye out at gunshow or the like to get another one.
__________________
Keep your Axe sharp and your powder dry. |
|
|