|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
June 25, 2012, 04:39 PM | #1 |
Junior Member
Join Date: June 25, 2012
Posts: 1
|
Gold filling for BPS engraved model?
Thinking about filling the engraved receiver on my 12 BPS with Forster Products 'gold' filling kit. Does anyone have any experience doing this on their weapons?
|
June 25, 2012, 06:15 PM | #2 |
Senior Member
Join Date: August 23, 2008
Location: SoCal
Posts: 6,442
|
Greetings my12bps, and welcome aboard.
I knew a couple of guys who got some gold paint stuff (I don't know the brand) to put in the engraving of their Citories. The stuff looked awful from the beginning and didn't get any better with age. IIRC, the problem was the stuff always seemed to have a ragged look the the edges. Where the original engraving had a clean edge the paint didn't follow it very well. Nobody is going to think your gun has gold filled engraving, they'll know it's just cheap paint. |
June 25, 2012, 06:38 PM | #3 |
Senior Member
Join Date: September 19, 2008
Posts: 4,678
|
The "kit" isn't needed - just a small bottle of Gold paint from a Train/Airplane Hobby Shop, a few tissues/Kleenex, a wooden toothpick, and some lacquer thinner.
Work on only one area/surface at a time. 1) Degrease the roll-stamped "engraving" with laq thinner on a rag or tissue paper by flowing it on & rubbing lightly, then let the area air dry. (Drying occurs in a few mins) 2) Mix the Gold paint thoroughly by shaking the bottle vigorously for a minute or two, then dip one end of the toothpick into the paint to pick up a blob of paint, to fill the stamping/engraving fully. (don't worry about overfill/overrun at this point) 3) Let the paint start to "dry" for only a few minutes, before starting to LIGHTLY wipe off the overfill. 4) LIGHTLY dampen a tissue with laq thinner, and with the damp tissue wrapped around a fingertip, start to lightly wipe the gold paint off the top surface areas in/around the stamping/engraving. If you press too hard, or wipe in the same direction as a groove/line, the soft tissue will get down into the stamping/engraving & remove the Gold paint from where you want it to stay. There's plenty of time, to make a pass or two. When everything you want filled is done, let the Gold paint dry overnite before applying anything to the painted area. (Sometimes you can carefully oil the surrounding areas with a tissue wrapped around a fingertip, dipped in a bit of oil, & being careful not to oil the paint) The Gold paint will gradually wear off if it's constantly touched, hit with cleaning fluids and/or oil. Anyone who likes the look can easily enjoy it at low cost, and just as easily remove it if they change their mind, or decide to sell the gun to someone who doesn't like the look.. . |
June 26, 2012, 10:09 PM | #4 |
Senior Member
Join Date: March 2, 2010
Location: Alabama
Posts: 868
|
Interesting.....
I have several Brownings that the "gold" plating on the trigger is worn off. Will the gold paint work on triggers, or being that they get touched a lot, not stay?
J |
June 27, 2012, 12:22 AM | #5 |
Senior Member
Join Date: April 7, 2006
Posts: 10,981
|
Gold plating and gold paint look entirely different.
There is a paint stick that you just rub over your lettering and it fills it. Brownell's probably sells them. |
June 27, 2012, 09:10 AM | #6 |
Senior Member
Join Date: April 12, 2010
Location: Lake Martin, AL
Posts: 3,311
|
My recommendation would be gold gilt. It can be an expensive process due to the cost of the gold leafing, but the amount of gold leafing you would need is insignificant.
The basic process is to clean the surface, apply a thin surface of glue (only inside engraved surface or lettering), rub in the gold leaf (apply gold leaf to gun engraving and wax paper on other side, where your burninshing tool or rubbing finger is at, and rub it in), and finally apply a sealer to keep it protected. Below is a picture of an antique French clock I restored using the process. Notice wth hunter with his gun and the rabbit. The most difficult part of my project was preparing the surface for gilting. Doing the roll marks or engraving on a gun should be a snap. Depending upon the amount of detail, you might even want to apply a wax to the non-engraved suface to keep the gold inside the lines so to speak. It is easy to correct a mistake, a slip, or even remove if you do not like the look. Last edited by lamarw; June 27, 2012 at 09:32 AM. |
June 27, 2012, 09:40 AM | #7 | |
Senior Member
Join Date: September 19, 2008
Posts: 4,678
|
Quote:
I would simply polish off the remaining "Gold" to give the triggers an even Silver appearance. . |
|
June 27, 2012, 08:43 PM | #8 |
Senior Member
Join Date: April 7, 2006
Posts: 10,981
|
The plating on Browning triggers is 24K gold. Gold plating is soft, and doesn't wear well.
|
June 27, 2012, 10:15 PM | #9 |
Senior Member
Join Date: August 23, 2008
Location: SoCal
Posts: 6,442
|
I always thought having your gold trigger plating worn through was a sign of experience to be gladly achieved.
|
|
|