|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
August 2, 2002, 08:40 PM | #1 |
Senior Member
Join Date: August 15, 2000
Location: Sugar Land, Tx
Posts: 1,507
|
Need help: .45 Colt Hot n' Mild
Digging this one back up because I just found an immaculate stainless blackhawk for $250.
Did a search and couldn't find exactly what i need. Weshoot...or anybody that wants to answer... I'm probably gonna use Bullseye. Gonna shoot straight wheelweights out of a (hopefully) .452 cal 255 gr. mold. I know that the Ruger's are a little oversized. In the past, I haven't sized my bullets; just dropped them in a bucket of water and loaded 'em up. Anyway, I need a hot bear killer, milk-jug-full-of-water exploder (big medicine) and a softer (thinking 850-900 fps) plinking load. I'm not married to Bullseye, and any pet load is welcome. Try to include whether or not you use magnum primers. That's the info that's been mostly missing in previous posts on this subject. Also, haven't bought the mold yet, so any recommendations there would be good also. All my other molds are Lee, and they work fine for me. Thanks, everybody.
__________________
Ronnie- Proud Veteran, Neocon, Warmongering, Baby-Pincher |
August 2, 2002, 09:24 PM | #2 |
Senior Member
Join Date: August 8, 2001
Posts: 519
|
Probrably gonna want to switch powders, I've never heard of Bullseye giving good magnum level loads in the 45 colt.
I like Unique for the general thumping, and am playing with 2400 right now for magum loads, don't have final results yet, however. I am a big fan of Lees 255 gr mold, shoots well out of my Vaquero, my Italian, and my winchester all with the tumble lube alox. Good luck
__________________
The Forty-Four spoke and it sent lead and smoke And seventeen inches of flame. -Marty Robbins JM |
August 2, 2002, 11:15 PM | #3 |
Senior Member
Join Date: March 16, 1999
Location: So. CA Mountains
Posts: 540
|
I'm shooting a Lee version of the WFN 255. I use a load from the very bottom of the "Ruger & TC only!" list, 13.0 grains of Blue Dot, lit with a WWLP. I cast with wheelweights and a touch of lino, size to .454 and molyplate, them lube with Lyman's moly bullet lube.
It doesn't stress my 25-5, and gives me about 950 fps from the four-inch tube. Good accuracy. Some recoil, but pretty pleasant to shoot. With your Ruger, you could up the charge by a couple grains -- in cautious increments, and checking a manual to obtain maximums!! -- Or, you could cut back to around 10.0 or 11.0 gr. and have a very soft plinking load. IMHO, Blue Dot is a really good propellant for the .45 Long Colt... Tom
__________________
There are damn few situations so screwed up that adding government to them will not make 'em worse... The best homeland security is an armed & informed citizenery! Molon Labe! |
August 2, 2002, 11:33 PM | #4 |
Member
Join Date: May 19, 2002
Posts: 99
|
WW case
CCI 350 primer 21.5 grns. WW 296 300 grn. LFP slug Hard roll crimp Good for 1200+ fps out of a 5" barrel. An elk/bear killer of the first magnitude. Healthy recoil to say the least but manageable with a little practice. dfm |
August 3, 2002, 12:13 AM | #5 |
Junior Member
Join Date: June 1, 2002
Location: S.W. VA
Posts: 12
|
Light (cowboy) load
Lyman 255gn SWC, 4.7gn IMR 700X, CCI 300, 680 fps Heavy Load Lyman 255gn SWC, [POWDER WEIGHT REMOVED BY MODERATOR EDIT] 2400, CCI 350, 1304 fps Data derived with a 71/2 Blackhawk, Lyman 445244 ( I think thats the right #) cast of wheelweights, water quenched, Sized .454. Both loads very accurate in my revolver. Sorry--Well above published maximums without cautionary notes. - - - Johnny Guest Handloading & Reloading Forum Moderator
__________________
Rob Helms Last edited by Johnny Guest; August 3, 2002 at 04:51 AM. |
August 3, 2002, 06:43 AM | #6 |
Member
Join Date: February 2, 2001
Location: Beaufort County NC
Posts: 51
|
I posted the below on another forum some time back in June in answer to a question similar to yours;
"I just spent the afternoon (96 degrees! chronographing 10 different loads in two 45 Colt Rugers. I shoot lead bullets in my 5 1/2" barrelled NM Blackhawk and jacketed bullets in my 5 1/2" barrelled Redhawk. I have modified my Blackhawk to help with heavier loads. It has a Vaquero grip-frame (which is steel instead of aluminum). I also had the throats opened up to .4525, which reduces leading with hotter lead reloads and slightly reduces the pressure of a given load. The fellow I purchased it from had added a white line "V" type rear sight and a gold bead front sight - which helped with point of impact on heavy bullets. In the Blackhawk I got the following velocities (Chrony at 8' from the muzzle, all 250 grain lead bullets except the SWC which was 255 grains of lead and the Federal Classic at 225 grains of lead); Win Factory Cowboy loads - 682 fps avg 3-D Factory CAS loads - 688 fps avg 7.0 grains of HP38, CCI300 - 789 fps avg D-C Ammo (local commercial loader) - 805 fps avg 6.0 grains of TiteGroup, CCI300 - 819 fps avg Federal Classic Factory (225 lead) - 850 fps avg 18.5 grains of 2400, WLP 255 grain SWC - 1108 fps avg In the Redhawk I Chronied 3 loads (all jacketed); Win Factory 225 grn Silvertip-HP, 801 fps avg Corbon Factory 200 grain HP, 1177 fps avg 25.0 grains of H110, Hornady 250 XTP-HP, FED MAG primer, 1326 fps avg. On the last load (the Redhawk/Horn 250 XTP load) Hodgdon #27, page 138, lists it as 25.7 start - 26.5 max for Ruger and T/C ONLY! It is a "two handed" load - it would probably knock you in the head if you shot it weak-handed. It is my hunting load for black bear. The last Blackhawk load, the 255 SWC using 18.5 grains of 2400 is a perfect load and balanced to that Blackhawk. Had a fun day, with two great guns and a great caliber - have fun with it yourself!" NG Bruce |
August 3, 2002, 01:42 PM | #7 |
Senior Member
Join Date: April 24, 2000
Location: Northern Indiana
Posts: 519
|
The usual reply...
if you wanna shoot "heavy", go to http://www.sixgunner.com and read "Dissolving the Myth" by Linebaugh. I used his info and my RUGER/CONTENDER ONLY load is 24.0 of H-110 or WW-296 with a Keith style 255 LSWC and CCI Mag pistol primers. You'll know when this goes off. I've shot 1 1/2" groups at 20 yards and I'm not a great pistol shot.
For "general" use, RUGER ONLY, I use 10.8 of AA5, 255 LSWC and CCI or Winchester primers. This is only slightly hotter than the "old pressure" loads listed by the Accurate Arms manual and way low for their listing for the Ruger, but they shoot great, and don't beat you to death. Neat thing is that the two above loads shoot real close to the same POA in my Bisley. I have no idea why as the first load is obviously way hotter. I've used Red Dot, Bulleye, and Unique and they're all a lot dirtier. The "new" powders (AA5, Universal clays, Titegroup, etc) seem to burn cleaner. Unique looks like black powder when you shoot. |
August 4, 2002, 09:05 AM | #8 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
OKAY (but for safety's sake.....)
Medium load: any case, CCI350 (or Federal, too, but magnum primers NOT required, nor recommended --but I have my reasons), 255g LSWC (Penn Bullets offers a nice one), Redding Profile Crimp die (recommend heavy crimp unless going under 900fps), and some Universal Clays.
Can also try HS6 or W231, and any primer you prefer. Plenty of data for these powders, so you can be safe, accurate, and reliable IN YOUR GUN. Heavy loads: W296, magnum primers, heavy crimp, Starline cases, 300g-n-up bullets. Contact direct for further discussion; 45 Colt can go bad quick
__________________
. "all my ammo is mostly retired factory ammo" |
August 4, 2002, 08:08 PM | #9 |
Senior Member
Join Date: December 9, 1999
Posts: 4,131
|
DO NOT USE MY LOAD UNLESS YOU'RE A COMPLETE IDIOT. MY LOADS ARE ONLY SAFE IN MY GUN, AND THEN ONLY WHEN THE PLANETS ARE IN ALIGNMENT!!!
325 LBT-LFN (or in your case the WFN that you may purchase from Cast Performance) Starline case Mag primer Start at 21 grains of W296 don't top out over 24 for your sake. Anywhere in there will anchor a bear if you can. Redding profile crimp (thanks, Tim) You whould wish for the Bisley grip frame...you WILL wish for it after you touch that load off.
__________________
Favor the X. Steve Smith NRA Life Member |
August 4, 2002, 08:21 PM | #10 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
RIGHT ON, RIGHT ON STEVE!
I been hollered at before................
Welcome.
__________________
. "all my ammo is mostly retired factory ammo" |
August 5, 2002, 04:18 PM | #11 |
Member
Join Date: May 15, 2001
Posts: 34
|
Penn SWC's
Hi Tim -
What is unique about Penn's SWC's? I've shot up a bunch of their Hammerheads but I've always assumed their SWC's were of the generic magma design...like 99% of all commercial cast swc's? God Bless. |
August 5, 2002, 07:18 PM | #12 |
Senior Member
Join Date: December 9, 1999
Posts: 4,131
|
BTW, Thumper, since you have the Blackhawk "plowshare" grips, you'll find that the gun will limit your top-end loads more than pressure. When your hand feels like it is almost going to break, you're there.
The Bisley frame is much easier to shoot heavy loads with, and is easy to put on your gun. Brownell's sells them.
__________________
Favor the X. Steve Smith NRA Life Member |
August 5, 2002, 07:30 PM | #13 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
PENN
Their bullets are really nice.
Most impressed. Redhawk easier still..........
__________________
. "all my ammo is mostly retired factory ammo" |
August 5, 2002, 09:39 PM | #14 |
Senior Member
Join Date: August 15, 2000
Location: Sugar Land, Tx
Posts: 1,507
|
Good advice all, boys. Thanks.
I think I bought the wrong dadgum mold, though. It's the Lee R.E.A.L. 250 gr. .452 mold. Thing is, I think it's strictly for blackpowder. Hasn't gotten here yet, so I'm not sure. No excuse, but the Midway online catalogue was a little vague. Oh well, it's only 17 bucks.
__________________
Ronnie- Proud Veteran, Neocon, Warmongering, Baby-Pincher |
August 5, 2002, 10:50 PM | #15 |
Senior Member
Join Date: May 11, 2002
Location: high up in the rockies
Posts: 2,289
|
Thumper,
For a general purpose load, there's always the old standby. A Lyman mold 255 Kieth SWC, cast in wheelweights, (or a Rainier plated 250 grainer) Standard large pistol primer, and 8.0 Gr Unique. BTW, I do load HEAVY .45 Colt loads, and I don't find it necessary to use magnum primers at all. I don't use magnum primers in .357 or .44 max loads either. Using standard primers requires a small amount of additional powder to achieve max velocity, but in my experience, the loads are more accurate with the stanbdard primers. YMMV
__________________
If you think a mighty military force is expensive, wait 'til you see what a weak one costs. |
August 8, 2002, 03:25 PM | #16 |
Senior Member
Join Date: April 14, 2002
Posts: 299
|
Sreve
This should set your hair on fire: Cast the 300 gr RCBS rifle bullet out of wheel wts. It will weigh 325 gr. Size it to .454 now do this: Powder weight removed by moderator--Well above published maximums. H110, RCBS 325 GR, FED 155, R-P cases, use a heavy crimp This chrono at 1320 in my 4 5/8" Vaquero 45 LC. Before you ask I do shoot the .454 bullet in the .452 barrel. I also use double gas checks one on the back of the bullet and one cup down over the powder. The one cup down will scrape any lead out ot the barrel as the round is fired. This is a serious load and should be approached very cautiously. Last edited by Johnny Guest; August 11, 2002 at 05:09 PM. |
August 12, 2002, 09:12 AM | #17 |
Senior Member
Join Date: April 14, 2002
Posts: 299
|
MODERATOR
Sorry, I will post no more loads over max. |
August 12, 2002, 09:19 AM | #18 |
Senior Member
Join Date: December 9, 1999
Posts: 4,131
|
Duck, FWIW, I've used the same load, minus the double gas checks (I don't get leading with my bullets and lube). I just don't advertise that load.
__________________
Favor the X. Steve Smith NRA Life Member |
August 12, 2002, 09:31 AM | #19 |
Moderator in Memoriam
Join Date: August 28, 1999
Location: North Texas
Posts: 4,123
|
Over Max loads - - -
Once again, duck of death, I have no problem with people posting experimental data on this forum, so long as proper cautions are posted with them. This should take the form of BOLD PRINT or at least ALL CAPS notice, something like,
CAUTION: The included hand load information exceeds currently-published MAXIMUM LOADS. It is provided for reference only. USE AT YOUR OWN RISK! Neither TFL ownership nor staff assume any liability for damage or injury to persons or gear resulting from use of this information. Yeah, this is a minor hassle, but a cut-and-paste of the above should provide at least a minimal protection from law suits - - Showing that the writer at least made the effort to protect the user from himself. I have several pet loads that extend well beyond published data, but I assume responsibility only for those which I myself assemble, and which are fired in MY guns. Any other use of that information is just for reference. Very best regards, Johnny Guest H&R Forum moderator |
August 14, 2002, 08:45 PM | #20 |
Senior Member
Join Date: April 9, 2002
Location: Idaho
Posts: 597
|
Been using 10 grains of accurate #5 and 250 grain RNFP Lazer cast bullets. Seems quite accruate through my Rugers and Smiths and Winchester. Pleasant to shoot not hand busters.
|
August 16, 2002, 09:28 PM | #21 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
Blackhorse
Does your AA5 load leave a gritty residue?
__________________
. "all my ammo is mostly retired factory ammo" |
August 16, 2002, 10:02 PM | #22 |
Senior Member
Join Date: April 9, 2002
Location: Idaho
Posts: 597
|
Weshoot2, sometimes yes it does, the only thing I have been able to attribute it to is that I don't get all the media out when I pour the casings into the case feeder, because I don't seem to have that problem when I load on my single stage and feed the casings one at a time.
|
August 17, 2002, 01:48 AM | #23 |
Senior Member
Join Date: May 15, 2002
Location: Michigan
Posts: 1,429
|
I use 11.5 grains of blue dot with a 250 grain precision cast lead flat nose in a bird's head grip sheriff's model, and it is easily shootable in one hand.
The book says 900 FPS with regular primers, but I use magnum primers with blue dot, no matter what, so I don't really know. Plus the super-short barrel. It's accurate as all get out, that I know. |
August 18, 2002, 09:43 AM | #24 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
Blackhorse
When you use the single-stage you are getting a different primer seat and crimp; this accounts for your cleaner loads.
Mebbe.
__________________
. "all my ammo is mostly retired factory ammo" |
|
|