|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
April 17, 2012, 03:20 PM | #1 |
Senior Member
Join Date: May 29, 2002
Location: Illinois :(
Posts: 550
|
I almost hate to post this but : crimp question.
I know this thread will immediately diverge from the intent, but here's my question.
- I reload 44 magnum for a desert eagle. Hence I do -not- want to roll crimp the round. This causes noticeable feeding issues and is just a bad idea for a huge automatic like this. - I looked at getting a real 44 magnum taper crimp die. But the description is thoroughly baffling "The Lee Taper Crimp Die is hardened steel designed to overcome crimp problems caused by poor die design. These dies offer little or no advantage when used with 1986 or newer Lee dies as the crimp angle is already a modified taper crimp. Jacketed bullets must have a crimp groove (cannelure)." Ok, so the factory crimp die I have already roll crimps so I don't know how they can say it offers "little or no advantage" - I don't want a roll crimp, I want a taper crimp like the die name would seem to imply. Second, why would a taper crimp die say "jacketed bullets must have a crimp groove" ??? This is just baffling to me. I just want to taper crimp the rounds, not roll crimp. Why is finding the equipment for this so dang confusing. |
April 17, 2012, 03:31 PM | #2 |
Senior Member
Join Date: September 28, 2008
Posts: 10,442
|
Redding makes taper crimp dies for revolvers, including the .44M.
__________________
Walt Kelly, alias Pogo, sez: “Don't take life so serious, son, it ain't nohow permanent.” |
April 17, 2012, 03:46 PM | #3 |
Senior Member
Join Date: May 29, 2002
Location: Illinois :(
Posts: 550
|
Right, but I would still like to know what's up with the cryptic description of the Lee Taper Crimp Die. The word Taper is specifically in the name of the product, so.....it is a mystery.
|
April 17, 2012, 04:05 PM | #4 |
Senior Member
Join Date: November 9, 2005
Location: Ohio, Appalachia's foothills.
Posts: 3,779
|
Hornady also makes one.
I've made the switch to taper crimping all my revolver cartridges. Edit: Without a crimp groove, the jacket would get very diformed, or possibly severed. Sent from my HTC Wildfire S A510e using Tapatalk 2 |
April 17, 2012, 04:24 PM | #5 |
Senior Member
Join Date: May 29, 2002
Location: Illinois :(
Posts: 550
|
>Edit: Without a crimp groove, the jacket would get very diformed, or possibly severed.
Ok, so this sort of thing seems to happen whenever a crimp thread comes up. Sorry to pick on you But - I don't get why this matters at all. We are talking about a TAPER crimp here. I have never had a 45 acp bullet with a cannelure, and I always taper crimp. So why in a million years would a taper crimp die require a cannelure for 44 magnum. There really seems to be a severe terminology problem when it comes to crimps within the reloading community. |
April 17, 2012, 04:39 PM | #6 |
Senior Member
Join Date: November 9, 2005
Location: Ohio, Appalachia's foothills.
Posts: 3,779
|
Exactly. 45acp isn't really a crimp. Flare removal would be the correct term.
A true taper on a 45ACP would cause big problems since the round headspaces on the mouth rim. Sent from my HTC Wildfire S A510e using Tapatalk 2 |
April 17, 2012, 05:59 PM | #7 |
Senior Member
Join Date: June 9, 2010
Location: NEPA
Posts: 909
|
All revolver dies are made with a rolled crimp. Your Lee instructions are generic and the reference to tapered crimp does not apply to the 44Mag.
What type of feed problems is the crimp giving you? It shouldn't unless you are trying to crimp while seating the bullet. This might spread the case a little. If you crimp as a separate operation you should not have any feed issues. |
April 17, 2012, 06:43 PM | #8 |
Senior Member
Join Date: January 28, 2012
Location: Puget Sound
Posts: 293
|
Do factory 44 Mag rounds cause the same problem as your reloads? As far as I know, they are roll crimped. If they feed well, then the problem might be something other than your roll crimp.
__________________
Scharfschuetzer US Army Distinguished Rifleman Washington State Distinguished Rifleman NRA Police Distinguished Expert |
April 17, 2012, 06:58 PM | #9 |
Senior Member
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,930
|
Ok a little thing to try here. Take the FCD you have. Screw it down till it touches the shell holder at the top of the stroke. Back the screw in the top off as far out as it will go. This will give you a taper crimp. Taper crimp is fancy way of saying it will remove the case flare so that it will chamber in a factory spec chamber. The screw in the top of the FCD will set the amount of crimp for after the post sizing. For my .38 spcl I seat with no crimp removing most of the case flare. Next I run through the FCD enough to remove the rest of the flare. I back the screw in the top off all of the way.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you. |
April 18, 2012, 06:43 AM | #10 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
You can adjust the superior Redding Profile Crimp Die to only provide a taper crimp.
__________________
. "all my ammo is mostly retired factory ammo" |
April 18, 2012, 11:56 AM | #11 |
Senior Member
Join Date: July 6, 2000
Location: BLACK HILLS
Posts: 1,322
|
You Sir, are incorrect in ALL your statements and thoughts concerning a roll crimp vs taper crimp in that autoloading pistol.
IF you do not know HOW to adjust a roll crimp 44MAG die say so and maybe, MAYBE, we can help you here. EVERY one of those pistols is test fired at the factory with 44MAG ammunition with a very TIGHT roll crimp properly applied in the correct position, and for all the correct reasons. And so it goes... |
April 19, 2012, 04:42 PM | #12 |
Senior Member
Join Date: January 14, 2011
Location: on the north side of DFW
Posts: 970
|
I was thinking the .44 mag ammo used in the DE pistols was roll crimped, as well.
Shouldn't be an issue... although I'm certainly not an expert in DE pistols.
__________________
I always felt that if I got to the point where I thought it was time to bury my firearms, it was actually time to pick them up.. |
April 19, 2012, 06:15 PM | #13 |
Senior Member
Join Date: November 9, 2005
Location: Ohio, Appalachia's foothills.
Posts: 3,779
|
My guess is he is not applying enough crimp and the case mouth is hanging up on something as it cycles forward.
Sent from my HTC Wildfire S A510e using Tapatalk 2 |
April 19, 2012, 06:40 PM | #14 | |
Senior Member
Join Date: May 12, 2002
Location: MO
Posts: 5,457
|
Quote:
I got on a heavy-bullet, hot load kick a few years ago and the gun I was shooting the most was a 4" Model 29-2. No, this is not a good idea. But I did it anyhow and my heaviest 300 grain loads would walk out some by the 4th or 5th round fired. Neck tension was excellent with the new Starline brass I was using. I was running a heavy roll crimp and I eventually started taper crimping them, too, right over the roll. This eliminated the problem in that particular gun. I'm not saying this is great or even recommending anyone else do it- just passing on my experience with it. I can't think of any reason, other than that particular manufacturer's recommendation, why you couldn't run a taper crimp on a non-cannelured bullet. I taper crimp my auto pistol loads into a cast bullet about half the thickness of the case mouth, and if they were inaccurate I would have discontinued the practice long ago. I crimp the few jacketed bullets I load pretty firm too; you can feel the bump on the press handle when it sets. Again, no accuracy problems and certainly no problems with setback despite repeated trips up the feedramp.
__________________
People were smarter before the Internet, or imbeciles were harder to notice. |
|
April 19, 2012, 07:16 PM | #15 |
Senior Member
Join Date: September 28, 2008
Posts: 10,442
|
Mebbe' it's more of a problem with the belling of the case mouth.
Try only belling the cases just enough to allow the bullets to start. Then try the roll crimp die again. If the cases are belled out too much, the roll crimp die might not be able to do its job well. The belling might be springing back just enough to cause the feeding problems. Just a thought.
__________________
Walt Kelly, alias Pogo, sez: “Don't take life so serious, son, it ain't nohow permanent.” |
April 21, 2012, 10:30 AM | #16 |
Senior Member
Join Date: February 16, 2008
Location: Michigan, Upper Pennsula
Posts: 396
|
This is from the lee web site....
"A carbide sizer inside the Carbide Factory Crimp die post-sizes the cartridge while it is crimped so every round will positively chamber freely with factory like dependability. The adjusting screw quickly and easily sets the desired amount of crimp. It is impossible to buckle the case as with a conventional bullet seating die. Trim length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered. Revolver dies roll crimp with no limit as to the amount. A perfect taper crimp is applied to auto-loader rounds. The crimper cannot be misadjusted to make a case mouth too small to properly head-space. A firm crimp is essential for dependable and accurate ammunition. It eliminates the problems of poor ignition of slow burning magnum powders. If you don't see your caliber listed, check out our custom services page. from the Lee web site....." The second paragraph refers to there revolvers dies. I reload for the 44 mag revolver and my rounds get taper crimp. but that is the die i ordered.
__________________
CarpriverShOOter Finch, I don't like guns. Reese, Me either but if someone has to have guns I'd rather it be me. (Person of Interest). No trees were destroyed in the posting of the this message |
|
|