|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
February 12, 2013, 08:45 PM | #1 |
Senior Member
Join Date: December 8, 2012
Location: Clearwater, FL
Posts: 237
|
Tumbler Media Replacement
I am using crushed walnut shells as my media in my tumbler with no additives. Local reloading store said additives are not needed unless you are look to have your brass look band new. My question is how do I know when I should change the media? So far I have ran over 3000 rounds through the tumbler.
|
February 12, 2013, 10:10 PM | #2 |
Senior Member
Join Date: January 25, 2009
Location: Liberty Twp, OH
Posts: 283
|
If you buy it in bulk 25 lb boxes you are ready to switch out in my opinion. First, try 2 tbl spoons of mineral spirits and 2 tbl spoons of Nu Finish in it. Run it empty for 15 minutes to distribute the liquid (with two used fabric softener sheets cut in quarters- optional. Pull them and replace with new used sheets every other batch.) This will shock you as to how the polish helps shorten tumble time and the mineral spirits/sheets cut down on dust.
|
February 12, 2013, 10:18 PM | #3 |
Senior Member
Join Date: June 30, 2009
Location: dallas
Posts: 773
|
Its all personal choice on how clean and shiny you want it to be but 3000 is just a start, its got a long way to go. I clean about 300 a week and change media maybe in 6 to 8 months. You probably will notice it takes longer but it is still usable. If it just doesn't seem to be doing a good job then go ahead and change it.
|
February 12, 2013, 10:19 PM | #4 | |
Member
Join Date: August 1, 2012
Location: Florida
Posts: 98
|
Quote:
|
|
February 12, 2013, 10:39 PM | #5 |
Senior Member
Join Date: January 25, 2009
Location: Liberty Twp, OH
Posts: 283
|
+1 on HF bulk walnut media. The only way to go. I think my whole tumbling set up with: HF tumbler; a 25lb box of walnut media; and mineral spirits cost me $75 at HF a few years ago. I then went to the dollar general store next door and bought a bottle of Nu Finish and two 4 qt colanders for less than $5.
Pull a 20% coupon from the paper and get the media real cheap. |
February 12, 2013, 11:30 PM | #6 |
Senior Member
Join Date: October 28, 2007
Location: Upper Indiana
Posts: 609
|
One more time
http://www.drillspot.com/products/52...bs_blast_media Corn Cob shipped right to your door, 40 lbs for approx $35 bucks, plus 40 lbs of corn cob is a heck of lot more material that 40 lbs of walnut, that you spend gas to get. As far as the tumbler, I tired the Harbor Freight one, burned the motor out in the first week, got a replacement and did the same thing, tried one more time and burned the third motor up, got my money back. Suggest one goes to Cabela's and buy their #400 tumbler, same price range and made right here in America not supporting the RED chinese "friends". Granted the berry tumbler sold by Cabela's motor is made in china but it only because no company here makes one to their specs. Mines been running now for over 10 years now with no problems. Oh, one more thing, Cabela's gives you a lifetime satisification warranty. Course if you're one who wishes to support labor other than our own when the product is in the same price range, by all means shop for the chinese junk.
__________________
U.S. Army Veteran NRA Certified Range Officer |
February 12, 2013, 11:45 PM | #7 |
Senior Member
Join Date: January 9, 2013
Posts: 131
|
I don't know which makes me feel guiltier. Buying a HF tumbler or that it works. Berry's tumbler is made out of unobtanium. Most of the ****e at Cabelas is made in China. hmmmm. Now where did I leave that rope?
|
February 13, 2013, 02:27 AM | #8 | ||
Senior Member
Join Date: November 10, 2010
Posts: 1,149
|
Quote:
Quote:
|
||
February 13, 2013, 08:06 AM | #9 |
Junior Member
Join Date: April 29, 2012
Posts: 13
|
I bought a used RCBS tumbler years ago and ran it with the walnut hull media that came in it until about a month ago when I changed it out with corn cob media that I got a deal on. The old media still worked OK, just was taking a long time and had a lot of dust in it. I can't tell much difference with the corn cob media...both seem to work fine.
|
February 13, 2013, 08:23 AM | #10 |
Senior Member
Join Date: April 4, 2012
Location: South Jersey
Posts: 2,217
|
What are you doing with the cartridges after they come out of the tumbler?
Wash them, air hose or just shake them in colander till the dust falls off then load/
__________________
Concentrated power is not rendered harmless by the good intentions of those who create it. Milton Freidman "If you find yourself in a fair fight,,, Your tactics suck"- Unknown |
February 13, 2013, 11:30 PM | #11 | |
Senior Member
Join Date: October 28, 2007
Location: Upper Indiana
Posts: 609
|
Quote:
__________________
U.S. Army Veteran NRA Certified Range Officer |
|
February 14, 2013, 12:03 AM | #12 |
Senior Member
Join Date: May 29, 2008
Location: now living in alabama
Posts: 2,433
|
I havnt had a problem with Frankfort Arsenal's tumbler. Hornady and RCBS make good ones also. As for media, I prefer corn cob. When the media starts to change color I replace it with fresh.
__________________
No such thing as a stupid question. What is stupid is not asking it. |
February 14, 2013, 02:09 PM | #13 |
Senior Member
Join Date: January 28, 2013
Location: Land of 10,000 taxes
Posts: 211
|
Purchased the cheapest Frankfort Arsenal's tumbler kit 3+ years ago. Still working great and would recommend it. Corn cob meadia that came with kit broke down relatively quick. Replaced with Walnut and still using it. My only complaint was the dust so I tried the used softener sheet trick. Works great..... I try to use a full sheet every other load, dependent on available supply. I do run brass for a short while in corn cob after walnut to removed any left over dust that usally show up on the inside of the case.
|
February 16, 2013, 02:46 PM | #14 |
Senior Member
Join Date: June 15, 2009
Location: Minnesota CZ fan
Posts: 902
|
I use walnut for cleaning and corn for polishing. I change it when it either gets really dusty or quits doing it's job. Pretty black b4 it quits for walnut but not too dark when CC gets too dusty.
|
February 16, 2013, 04:05 PM | #15 |
Senior Member
Join Date: December 5, 2009
Posts: 1,411
|
A dryer sheet in the bottom really helps keep down the dust and lets you use the media longer. When it takes a long time to clean the brass it is time to replace it. You can add stuff like Dillon brass polish to speed the cleaning process up. NuFinish will help as well, Nufinish also will apply a very thin polymer type polish to keep the brass from tarnishing for quite a while. It doesn't hurt the ammo or gun either.
It may not be in the interest of someone selling media to tell a customer how to make it last longer or quicker. When you add things like polish to the media you need to do it when it doesn't have any brass in it. Run the tumbler at least 15 minutes (30 is better) before you add brass. Last edited by Misssissippi Dave; February 16, 2013 at 04:14 PM. |
February 16, 2013, 08:14 PM | #16 |
Senior Member
Join Date: January 16, 2010
Location: If you have to ask...
Posts: 2,860
|
No idea how long walnut media will last, current batch is several years old. I just clean it and add new polish now and then. I have a new bag of media around so someday I might just change it out before I forget where I put it.
__________________
Life Member NRA, TSRA Smokeless powder is a passing fad! -Steve Garbe I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call Lonesome Dove My favorite recipes start out with a handful of used wheelweights. Last edited by TXGunNut; February 16, 2013 at 08:27 PM. |
|
|