T7 Redding

SeanB · January 23, 2006, 04:42 AM

Gentlemen. Recently I purchased a T7 turret to accomodate some extra
reloading. Already have a T6 Redding turret press and it has been faultless.
After mounting the T7 it would not accept a shellholder. I tried 4 different
manufacturers including Redding with no success.

Anyone have a similar issue.
Thanks
Sean

Thirties · January 23, 2006, 10:54 AM

Sean, did you push it in hard?

MADISON · January 24, 2006, 11:54 AM

First contact Redding and see what they say do.
I have a Lyman T-Mag press the shell holder would not fit on to. I took a file and went over the top of the ram. I took it down until A SHELL HOLDER would fit. I left things very stiff, so the shell holder would not fall off the ram.

SeanB · January 25, 2006, 04:26 AM

Without going over the top I did try reasonable force

Didnt want to attack the ram with a file as this will void warranty.
Just interested to hear if anyone had a similar problem.
thanks
Sean

Duke45 · January 29, 2006, 05:50 PM

I also have two redding turret presses and have no problems with the shellholders. The t-7 dose take a good amoumt of presure to seat the shellholder in the ram. Call the factory and see if they have a solution.Duke45

RERICK · January 29, 2006, 07:50 PM

Mine just pops right with ease.I too would contact Redding or maybe even who you bought it from they should take care of you.

SeanB · January 31, 2006, 03:54 AM

Sent it back for warranty repairs......best solution
thanks guys
SB

at2000 · January 31, 2006, 01:19 PM

I just bought one and the shellholders (made by RCBS) popped right in.

January 23, 2006, 04:42 AM	#1
SeanB Member Join Date: May 28, 2004 Location: Australia Posts: 50	T7 Redding Gentlemen. Recently I purchased a T7 turret to accomodate some extra reloading. Already have a T6 Redding turret press and it has been faultless. After mounting the T7 it would not accept a shellholder. I tried 4 different manufacturers including Redding with no success. Anyone have a similar issue. Thanks Sean __________________ Clean up your own mess

January 24, 2006, 11:54 AM	#3
MADISON Senior Member Join Date: January 1, 2000 Location: Roanoke, Virginia Posts: 2,678	T7 Redding shell holder First contact Redding and see what they say do. I have a Lyman T-Mag press the shell holder would not fit on to. I took a file and went over the top of the ram. I took it down until A SHELL HOLDER would fit. I left things very stiff, so the shell holder would not fall off the ram.

January 25, 2006, 04:26 AM	#4
SeanB Member Join Date: May 28, 2004 Location: Australia Posts: 50	Without going over the top I did try reasonable force Didnt want to attack the ram with a file as this will void warranty. Just interested to hear if anyone had a similar problem. thanks Sean __________________ Clean up your own mess

January 29, 2006, 05:50 PM	#5
Duke45 Junior Member Join Date: February 24, 2005 Posts: 3	t-7 I also have two redding turret presses and have no problems with the shellholders. The t-7 dose take a good amoumt of presure to seat the shellholder in the ram. Call the factory and see if they have a solution.Duke45

January 31, 2006, 03:54 AM	#7
SeanB Member Join Date: May 28, 2004 Location: Australia Posts: 50	Sent it back for warranty repairs......best solution thanks guys SB __________________ Clean up your own mess

January 23, 2006, 10:54 AM	#2
Thirties Senior Member Join Date: April 29, 2001 Location: Where the Red Sox meet the Black Bears Posts: 561	Sean, did you push it in hard?

January 29, 2006, 07:50 PM	#6
RERICK Junior member Join Date: July 9, 2005 Posts: 369	Mine just pops right with ease.I too would contact Redding or maybe even who you bought it from they should take care of you.

January 31, 2006, 01:19 PM	#8
at2000 Senior Member Join Date: February 29, 2000 Posts: 133	I just bought one and the shellholders (made by RCBS) popped right in.