|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
February 13, 2013, 07:15 PM | #1 |
Senior Member
Join Date: January 11, 2011
Location: Jupiter, florida
Posts: 233
|
cowboy loads with jacketed bullet?
I tried doing a search but could not find any results. This is in regards to loading 44 remington magnum cowboyloads. Can i use a jacketed bullet such as a 240gr nosler jsp on a 44 mag loaded with ff triple 7 and a CCI 300 primer and still be safe using it in a ruger super redhawk and marlin 1894? i have alot of this stuff laying around and i dont have the funds to get cast bullets or real BP.
|
February 13, 2013, 09:30 PM | #2 |
Senior Member
Join Date: December 26, 2008
Location: Greenville, SC
Posts: 591
|
Define "cowboy". If you are going to shoot in a SASS match, the rules require lead bullets only-no jacketed, plated or gaschecked bullets. Ricochet hazard on the steel targets we shoot in cowboy matches.
|
February 13, 2013, 09:46 PM | #3 |
Senior Member
Join Date: January 11, 2011
Location: Jupiter, florida
Posts: 233
|
low recoil and extra smoke. not really gonna use it for competition. just want some plinkining.
|
February 14, 2013, 08:05 AM | #4 |
Junior member
Join Date: February 10, 2009
Posts: 974
|
44 special was loaded pre ww1 with black powder and a metal jacketed bullet. but to be honest, you have a decent bullet that does well at normal 44 magnum velocity in regards to accuracy and expansion.
blackpowder will be a lot dirty, and youll most likely stop doing it after a few cylinders. |
February 14, 2013, 08:15 AM | #5 |
Senior Member
Join Date: July 31, 2000
Location: Middle Peninsula, VA
Posts: 1,588
|
It should be safe but it will not be low recoil. A full case of black powder is pretty stout.
|
February 14, 2013, 09:05 AM | #6 |
Senior Member
Join Date: February 28, 2008
Location: Michigan
Posts: 2,619
|
Just rmember if you load some T7, pyrodex or blackpowder, you WILL have a soap and water clean-up after the shooting session.
The soap and water is for everything guns and the case's. Regular bore solvents do not disslove the salts left behind after firing those powders. |
February 14, 2013, 03:12 PM | #7 |
Senior Member
Join Date: January 11, 2011
Location: Jupiter, florida
Posts: 233
|
Do I need to lube the bullet and do I need a heavy crimp?
|
February 14, 2013, 03:49 PM | #8 |
Senior Member
Join Date: July 28, 2007
Location: Ohio
Posts: 11,756
|
I shouldn't stick my nose in to a Black Powder (or substitute) thread but there's an alarm bell in the opening post and I don't think it's a bad idea to add some thoughts.
Coming *ONLY* from my smokeless powder perspective, if you are looking at published cowboy action load data (which, in my experience, is only EVER going to list cast or soft swaged lead bullets) and you attempt to simply insert a jacketed bullet in place of the lead one, you are asking for trouble. The published (smokeless!) load data that is specifically served up as "Cowboy Action" loads are very, VERY low in velocity and assumes a far-easier to launch lead bullet. Using this data with a jacketed slug will put you at great risk of sticking a jacketed bullet in the bore of your firearm. Sticking a jacketed slug in a bore really sucks. But it could be MUCH worse: if you pull the trigger on the next one when you've already got one stuck. Then you have major, major problems and at the very least...most likely a ruined firearm. In my opinion (again, I don't know anything about non-smokeless), your best bet in this situation is to find someone local and swap him this powder rather than looking for ways to "make it work." Someone wants the stuff and can likely trade you something that you will need.
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss. |
February 14, 2013, 04:30 PM | #9 |
Senior Member
Join Date: January 11, 2011
Location: Jupiter, florida
Posts: 233
|
And can you over compress the powder?
|
February 14, 2013, 04:48 PM | #10 | |
Senior Member
Join Date: June 6, 2007
Location: E. Oregon
Posts: 563
|
Quote:
|
|
February 14, 2013, 05:09 PM | #11 |
Senior Member
Join Date: January 11, 2011
Location: Jupiter, florida
Posts: 233
|
i guess ill wait till i can find or afford the powder and bullets
|
Thread Tools | Search this Thread |
|
|