Will Uberti parts work on my Euroarms Remington new model army

blkpdrkid · March 31, 2013, 12:31 PM

I baught a Euroarms Remington New Model army revolver and am having a difficult time finding extra cylinders. some one sayed parts from Euroarms and Uberti part will interchange. does any one know if there is any truth to this

Doc Hoy · March 31, 2013, 02:15 PM

You are best advised to call a parts house to verify compatability.

VTI, Dixie Gunworks, Winchester Sutler, or Deer Creek (Waldron Indiana)

I would talk to them on the phone. You may want to be prepared to tell them precisely how long your cylinder is.

jlb43 · March 31, 2013, 04:56 PM

Pietta BP cylinder was too long for my Euroarms. When I sent gun to Taylor's for a conversion cylinder they used a R&D made for a Pietta. Go figure.

Doc's advice should be heeded. Find a parts house, give precise dimensions, and ask their help.

Hawg · March 31, 2013, 05:08 PM

Nobody's parts are going to be drop in. You may find some that can be fitted with a little work.

**4V50 Gary** · March 31, 2013, 05:39 PM

Agree with Hawg. Plan to do some fitting and be grateful if it needs it. That way you can make sure it works right the first time.

Hellgate · April 1, 2013, 12:19 PM

I had a Euroarms Remmie that had a horribly machined cylinder that locked up the gun after two shots due to extreme shaving of lead from poor allignment of the chambers with the barrel. A spare Uberti cylinder dropped right in and functioned well. The only difference was the gap was about .009" rather than my desired .003-.007".

DPris · April 1, 2013, 08:17 PM

Call VTI & discuss.
Denis

blkpdrkid · April 6, 2013, 03:56 PM

ok thank you all your advice has been very helpful

March 31, 2013, 12:31 PM	#1
blkpdrkid Junior Member Join Date: March 29, 2013 Posts: 2	Will Uberti parts work on my Euroarms Remington new model army I baught a Euroarms Remington New Model army revolver and am having a difficult time finding extra cylinders. some one sayed parts from Euroarms and Uberti part will interchange. does any one know if there is any truth to this

March 31, 2013, 02:15 PM	#2
Doc Hoy Senior Member Join Date: October 24, 2008 Location: Naples, Fl Posts: 5,440	Euroarms is Armi San Paolo. You are best advised to call a parts house to verify compatability. VTI, Dixie Gunworks, Winchester Sutler, or Deer Creek (Waldron Indiana) I would talk to them on the phone. You may want to be prepared to tell them precisely how long your cylinder is. __________________ Seek truth. Relax. Take a breath.

March 31, 2013, 04:56 PM	#3
jlb43 Senior Member Join Date: March 26, 2010 Location: North Georgia Posts: 128	Pietta BP cylinder was too long for my Euroarms. When I sent gun to Taylor's for a conversion cylinder they used a R&D made for a Pietta. Go figure. Doc's advice should be heeded. Find a parts house, give precise dimensions, and ask their help. __________________ "Peace is that brief glorious moment in history when everybody stands around reloading" - Thomas Jefferson . --

March 31, 2013, 05:39 PM	#5
4V50 Gary Staff Join Date: November 2, 1998 Location: Colorado Posts: 21,829	Agree with Hawg. Plan to do some fitting and be grateful if it needs it. That way you can make sure it works right the first time. __________________ Vigilantibus et non dormientibus jura subveniunt. *Molon Labe!*

April 1, 2013, 12:19 PM	#6
Hellgate Senior Member Join Date: November 18, 2010 Location: Orygun Posts: 869	I had a Euroarms Remmie that had a horribly machined cylinder that locked up the gun after two shots due to extreme shaving of lead from poor allignment of the chambers with the barrel. A spare Uberti cylinder dropped right in and functioned well. The only difference was the gap was about .009" rather than my desired .003-.007". __________________ With over 15 perCUSSIN' revolvers, I've been called the Imelda Marcos of cap & ball. SASS#3302 (Life), SASS Regulator, NRA (Life), Dirty Gamey Bastards #129 Wolverton Mtn. Peacekeepers (WA), former Orygun Cowboy (Ranger, Posse from Hell)

March 31, 2013, 05:08 PM	#4
Hawg Senior Member Join Date: September 8, 2007 Location: Mississippi Posts: 16,188	Nobody's parts are going to be drop in. You may find some that can be fitted with a little work.

April 1, 2013, 08:17 PM	#7
DPris Member Emeritus Join Date: August 19, 2004 Posts: 7,133	Call VTI & discuss. Denis

April 6, 2013, 03:56 PM	#8
blkpdrkid Junior Member Join Date: March 29, 2013 Posts: 2	ok thank you all your advice has been very helpful

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search