The Firing Line Forums

Go Back   The Firing Line Forums > The Conference Center > General Discussion Forum

Reply
 
Thread Tools Search this Thread
Old January 7, 2014, 03:34 PM   #1
Devdev08
Member
 
Join Date: November 23, 2013
Location: Minnesota
Posts: 74
Gun range backstops

What are used for the backstops at indoor gun ranges and why do some only accept handgun caliber a and others can take anything? And I hope I put this in the right thread
Devdev08 is offline  
Old January 7, 2014, 04:00 PM   #2
4EVERM-14
Senior Member
 
Join Date: November 12, 2006
Location: Pennsy
Posts: 720
Various grades of steel are used in some backstop systems angled to deflect the projectile either down into a sand box or pitched back into a scroll device. A vertical stop will cause the bullet to stop dead but splatter lead bits in all directions. An angled stop tends reduce potential splatter and direct it into a catching media. Another popular backstop material is a ground rubber media. Ranges with this type backstop tend to allow more powerful ammunitions as the rubber media catches the bullet with little penetration and deformation. It requires regular service but reduces lead dust substantially. With OSHA bullying itself into the world of shooting ranges lead contamination has become a hot topic for range operators.
__________________
David
NRA Benefactor Member
Distinguished Rifleman #731
Presidents 100
4EVERM-14 is offline  
Old January 7, 2014, 04:17 PM   #3
FrankenMauser
Senior Member
 
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,400
Quote:
why do some only accept handgun caliber a and others can take anything?
Different backstops are built to different standards.
If the range has a backstop that's only rated for handgun rounds, whacking it with higher power cartridges will damage or destroy it.


The little steel rimfire 'spinner' targets that you can buy at big box stores are a good example. You can shoot them with rimfire cartridges all day long, and it doesn't hurt them. But, if you pull out your .45 Auto, and whack the target, it will cause significant damage (denting, bending, cracking). If you jump up to a .223 Rem, it'll punch holes right through the steel.
__________________
Don't even try it. It's even worse than the internet would lead you to believe.
FrankenMauser is offline  
Old January 7, 2014, 06:09 PM   #4
g.willikers
Senior Member
 
Join Date: September 28, 2008
Posts: 10,442
That ground up rubber, piled high and deep, really works as a backstop.
It captures the bullets, just about eliminating ricochets and splatter, and keeps the air cleaner, too.
Very good stuff.
__________________
Walt Kelly, alias Pogo, sez:
“Don't take life so serious, son, it ain't nohow permanent.”
g.willikers is offline  
Old January 8, 2014, 01:16 PM   #5
Uncle Buck
Senior Member
 
Join Date: June 21, 2009
Location: West Central Missouri
Posts: 2,592
A Little Off Target Here

G. Willikers mentioned the ground up rubber.

For my backstop I have found that cutting the tread off of tires and screwing it to a piece of 3/4 inch plywood works wonders at stopping a bullet from a handgun. Right now I only have two layers of tread and it stops most handgun bullets.
__________________
Inside Every Bright Idea Is The 50% Probability Of A Disaster Waiting To Happen.
Uncle Buck is offline  
Old January 8, 2014, 04:54 PM   #6
g.willikers
Senior Member
 
Join Date: September 28, 2008
Posts: 10,442
Yeah, tires are amazing.
We were shooting at stuff on the ground, in front of an old tire, with .44 mag revolvers.
The bullets were skipping off the ground and hitting the tires, like they were supposed to.
But they didn't penetrate, just got stuck in the tread.
At the local club, they used to use stacks of tires for side berms, to divide the range into separate ones.
They worked good for many years like that.
__________________
Walt Kelly, alias Pogo, sez:
“Don't take life so serious, son, it ain't nohow permanent.”
g.willikers is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:20 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.07922 seconds with 10 queries