|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
March 16, 1999, 06:04 PM | #1 |
Senior Member
Join Date: March 5, 1999
Location: Arbuckle, CA, usa
Posts: 1,269
|
I'm looking for two different powders to load up some 357's. A real fast one that will finish it's burn in 2 1/2" of barrel and a slower one that will fill a 8". does anyone have any recomendations? I'm also looking for a good source for the powder and primers. Best prices I've come up with so far is $50 per 5000 on the primers and $14 per pound on powder. Thanks, Richard P.S. Golden rule of reloaders.... It don't save you any money... It just allows you to shoot more for what you spend... |
March 17, 1999, 07:21 AM | #2 |
Senior Member
Join Date: January 23, 1999
Location: Southern Iowa
Posts: 211
|
Bullseye is about as fast a powder as I can find in my load book I don't think you gave a bullet weight so I can't give you powder weights.
As for the longer barrel Unique, 2400, Blue Dot, and H110 spring to mind. Blue Dot, and H110 burn cleaner than the other two. Unique tends to give you the most loads per pound. Unique also can be used in just about any hand gun or Shotgun load there is, and even some reduced power rifle loads. And I've heard that 2400 is very consistant. (but very dirty) Hope this helps a bit. |
March 18, 1999, 03:19 PM | #3 |
Senior Member
Join Date: November 3, 1998
Location: Alamo, CA
Posts: 424
|
bookie; your prices sound very good. Buy enough primers and powder so that you can stick with the same lots (once you select a powder and primer that you like).
The American Rifleman did a study on velocity and bbl. lengths some years ago. They concluded that the powders that will produce the highest velocities in longer bbls. produce the highest velocities in shorter bbls. I know that this doesn't seem reasonable, but it was the case. Further, if you use a faster powder for maximum loads, you are risking a great deal. The pressure obtained tends to be more affected by the typical variables; powder lot, primer brand and lot, brass brand and lot, bullet brand and lot, handgun used, temperature, etc. It is easy to obtain overpressure trying to make maximum loads with fast powders. I had a near death experience when in my 20's; there was this guy shooting his M 29 .44 Mag, and couldn't hit the target. I tried it out, and got all the shots in the black, but noticed the loads were really hot. He then told me how much Bullseye he was using, and I am sure I blanched. I hurriedly put my stuff away and got out of there. I use 2400 or H-110 in my 3" SP-101, and have had good results. Likewise in my M 66 6" bbl. Be extremely wary of using primer condition in an attempt to judge pressures. I was shooting some hot, but not max loads in my .357 (essentially the old Elmer Keith .38 Spl load which was really MUCH too hot). The recoil, and extraction seemed in line with the expected pressure. I looked at the (new) primers, WSPM's, and was horrified to see cratering, flow into the firing pin hole, and flattening. I went back to the identical loads I had loaded and fired, except with my usual Rem 5 1/2 small pistol Mag primers. These primers, as I had noted before, showed absolutely NO signs of over pressure; in fact, they looked like .38 Spl mid range loads! All things considered, I think that the pressure was the same in the two different loads, but the primer cup was softer on the WSPM's. Had I been trying to judge pressure with the Rem's, I would have been badly misled. So, be careful. Hope this helps, Walt |
March 18, 1999, 09:12 PM | #4 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
Try AA9. It has the right characteristics for 'hot' 357 loads.
|
March 20, 1999, 10:21 AM | #5 |
Member
Join Date: March 7, 1999
Location: Rome, NY, USA
Posts: 16
|
I agree , Bullseye is a good powder.. it burns fairly clean and is quite popular
amoungst the competitive shooters.. As far as prices go.. I have seen Bullseye and Unique on sale at Natchez for 44.96 for 4 lbs of powder.. Additionally, remember that the hottest load isn't always the most accurate.. |
March 20, 1999, 05:27 PM | #6 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
If you MUST use only one powder you can't do much better than Universal Clays. It's like Unique except MUCH cleaner (and meters more accurately in some measures).
|
March 20, 1999, 08:30 PM | #7 |
Member
Join Date: February 18, 1999
Location: thomaston,ga USA
Posts: 17
|
I agree with weshoot,Universal is tough to beat.You want get top velocity,but top velocity doesn't always equate to accuracy
|
March 20, 1999, 10:32 PM | #8 |
Senior Member
Join Date: December 6, 1998
Location: mytown,mi,usa
Posts: 162
|
I have started to like imr4227 for all my magnum revolvers. Yes it does not give the highest velocity but the muzzle flash is much reduced. I am willing to shoot 1350 instead of 1450 if I do not have the flash I get with h110 or win 296.
ps. I shoot better with less flash/blast |
|
|